Throw the ball joints in the frig overnight and a light bulb on the knuckle for an hour and the parts will fall in - good stuff from a mill valley 03 TJ and 93 XJ owner
@mrsdoylespinniedoyle1956
Жыл бұрын
Thanks for the video. I wasn't sure whether to do top or bottom first (or if it matters) but it's nice to see it being done by an expert. Here's hoping that refitting is easier than removal was.....
@ponypwr
Жыл бұрын
Best instructional dana 30 video ive found! Thanks brother!
@briandurham3273
3 жыл бұрын
Usually watch your videos. You explain everything in depth very well. Bringing my 93 YJ back alive out here on the coast of Oregon. Getting it ready for hunting season and it’s my daily driver. Some day like to meet ya to go wheeling. Anyways thanks man it helps a lot.
@JeepSolid
3 жыл бұрын
Awesome! Thank you. I hope to arrange a meet up sometime soon..
@askme2669
2 ай бұрын
just ignore the sleeve that comes with the lower ball joint just like the snap ring if you cleaned rust from bottom seat of ball joint you will get snap ring on armature
@rogerheath4348
3 жыл бұрын
Thank you so much for this video. I have been fighting that snap ring and was wondering if I had done it incorrectly, or if the ball joint I purchased was incorrect. I didn't realize that those not slipping back on is a common issue.
@borntobewild846
29 күн бұрын
Had a question. Would it be a good idea to put some anti-sieze on the ball joints as you're pressing them in?
@Wayne_Nero
Жыл бұрын
Great video! I realized i needed a bigger hammer!! Also what is that white thing on your axel shaft?? Some kinda bushing?? I don’t have one and I am looking for the part in the service manual
@antlese
4 жыл бұрын
You make it look easy.
@TheGoshood
3 жыл бұрын
great video. most helpful.
@pujo28
Жыл бұрын
What r your thought on removing & replacing ball joints with an air hammer?
@seanhuggins4086
3 жыл бұрын
Very well done, thank you
@JoeRed
3 жыл бұрын
Just wanted to say thanks, I fought with swapping my ball joints a few hours before I found your videos.
@JeepSolid
3 жыл бұрын
Glad it helped!
@MuzzleFlashTV
2 жыл бұрын
Did you have any plastic pieces on the axle shafts? I’m hearing those are needed to align the shaft splines with the differential splines.
@BroncoSolid
4 жыл бұрын
This feels familiar
@JeepSolid
4 жыл бұрын
Haha! Yep
@pujo28
Жыл бұрын
What are your thought on TRQ brand which is 1AAuto’s brand? I have a TJ and have to replace all the steering and suspension components. Thanks
@utuber2940
4 жыл бұрын
I see you like cats...I just subscribed..😀
@froggerman44
3 жыл бұрын
If u use a splined ball joint, can a smooth ball joint be put in its place?
@thomasgreen7113
3 жыл бұрын
Did you have trouble pressing in the upper ball joint because of the angle of the upper knuckle? I destroyed the boot on my first one.
@dominicsardina4324
3 жыл бұрын
Hello there I watch all you videos and they are so helpful I’m told I need an offset upper ball joint To get the wheel alignment correct because my YJ drifts to the right and they need more adjustment to correct the drift, my concern is when you pull the axle out does the 4wd vacuum coupling have any issue when you pull the axle out or putting it back in, please reply with your expert advise, thanks
@gordongman3423
4 жыл бұрын
Job well done..
@JeepSolid
4 жыл бұрын
Thanks Gordon
@albertonevarez7392
3 жыл бұрын
Torque of the wheel hub nut please
@dissociativecat7495
4 жыл бұрын
tootsies the real boss
@JeepSolid
4 жыл бұрын
Haha! Yep
@dissociativecat7495
4 жыл бұрын
@@JeepSolid hope you're staying safe, you got PPE at work ? No shortages I hope
@JeepSolid
4 жыл бұрын
Thanks. I am 👍🏼
@-_-John-_-
11 ай бұрын
✅
@maintenance96
4 жыл бұрын
Anti-seize!!! Can preach enough to others to use anti-seize on the hub bearing and bolts.
@leskobrandon538
4 жыл бұрын
De ja Vue?
@JeepSolid
4 жыл бұрын
Yes sir, it is. I didn't cover the issue people have with the grease fitting very well when I did it last. So, I'm taking the old one down and re releasing it with better info 👍🏽
@LimonEllie
4 жыл бұрын
Next time make sure you lineup the Cotter pin hole from front to back of the Jeep
@bobbemoras9334
4 жыл бұрын
Snap ring on lower doesn't fit. 1 side is angled where the ball joint is pressed.
@rogerheath4348
3 жыл бұрын
I'm here watching this video for the exact same issue. Not sure what I'm doing wrong hoping that this video teaches me.
@Fossildobber
4 жыл бұрын
What is the white thing on the axle outside of the knuckle?
@thomasgreen7113
3 жыл бұрын
Axle shaft oil slinger. Quadratec carry this part.
@thomasgreen7113
3 жыл бұрын
Crown Automotive 83500201 Outer Axle Shaft Oil Slinger for 87-95 Jeep Wrangler YJ, 84-01 Cherokee XJ & 93-98 Grand Cherokee ZJ with Dana 30 Front Axle
@thomasgreen7113
3 жыл бұрын
Sorry this is the one you asked about.
@thomasgreen7113
3 жыл бұрын
Crown Automotive 4797769 Axle Shaft Inner Slinger for 90-95 Jeep Wrangler YJ, 90-96 Cherokee XJ & 93-96 Grand Cherokee ZJ with Dana 30 Front Axle - Plastic Material
Пікірлер: 43