Note that at 8:10 when he “found” tdc, he didn’t have the cam sprocket bolted to the cam shaft, so it just turned the sprocket not the shaft.
@TBoltUSA
5 жыл бұрын
Awesome video, bud! Very thorough.
@SphynxKing
7 жыл бұрын
Awesome DIY Tech...I'll be referencing this when I replace my rings,you did a great job,Well Done man...Props and thx for taking the time to record,post,and share
@ethansmith244
6 жыл бұрын
Just found your channel... subscribed
@toddnewman2680
2 жыл бұрын
Great video! We have a 05 KLX110 and my son wants more power, esp bottom end. Is a big bore kit worth it or should we just go with a Pirahna 140 for $2300? Thanks
@killerkork
8 жыл бұрын
u-folw filter is pretty good !
@anthonywiley6649
5 жыл бұрын
Check out my two stroke exhaust on my klx125 sounds so sick !!
@casebabase
5 жыл бұрын
So if I put a 178cc Big bore on my 110 will I have to put on a new head or can I use the stock head
@blazeonsticks8767
5 жыл бұрын
ThatMXchannel 22 stock head (should) work.
@warpoet6977
4 жыл бұрын
Did you go for it ? Did it work ? cuz I’m lookin at the same thing
@fuglypanda8228
6 жыл бұрын
hey where did you get the instructions
@crazyskullcrusha
6 жыл бұрын
I didn't have any instructions. I bought the kit off of a friend and he didn't have instructions for it.
@Logannorth1988
4 жыл бұрын
I'm about to purchase this kit for my boys bike...his is a 2018 does it need the cam? I dont think it does I'm just checking to make sure...thanks!
@crazyskullcrusha
4 жыл бұрын
Take a look at TboltUSA website. I think you can find the answer there.
@itzkronik9003
7 жыл бұрын
I'm the 300th sub
@crazyskullcrusha
6 жыл бұрын
Thanks for subscribing!!!!
@r8motorsports113
7 жыл бұрын
Same for drz
@moosemilk8956
7 жыл бұрын
I'm assuming you can just rejet the existing carb, not buy a new one?
@crazyskullcrusha
7 жыл бұрын
Moose Milk I'm not sure on that question. I installed a 26mm Mikuni when I installed the big bore kit. Stock carb is an 18mm Keihn. I had to jet my 26mm Mikuni a bit as well. It is possible that the stocker carb would work with jetting but I have no experience with that.
@kulayowilliams1177
3 жыл бұрын
Will this work with a 2012 KLX 140L?
@joedirt72
3 жыл бұрын
No
@charlieglowacki7340
7 жыл бұрын
Where did you get your bbr swing arm.
@crazyskullcrusha
7 жыл бұрын
Charlie Glowacki I don't have a BBR swing arm. Mine is stock.
@r8motorsports113
7 жыл бұрын
Did the casing have to be midified
@crazyskullcrusha
7 жыл бұрын
DGAFM DGAFM Nope.
@maxrokusek4470
7 жыл бұрын
Would anyone recommend putting a 178cc big bore on a KLX 110 becuase I know there is not a lot of those kits out and I was wondering if I should just go with that or a 143cc
@pinnhead13
7 жыл бұрын
TB 143 kit is more than enough power for most
@crazyskullcrusha
7 жыл бұрын
Eric Spano I have to agree. I weigh 200 LBS and my KLX pulls me around with ease. First gear is almost unusable. Now a 178 kit with taller gearing could be a lot of fun but the problem is that the bike isn't designed for that kind of power. Might end up breaking other components such as the transmission.
@dylanwestbrooks8016
6 жыл бұрын
crazyskullcrusha what about the clutch is it stock or what
@dylanwestbrooks8016
6 жыл бұрын
Do I need a clutch or will it be fine
@crazyskullcrusha
6 жыл бұрын
Dylan Westbrooks You don't need a clutch. Your bike should already be equipped with one.
Пікірлер: 35