By far the simplest and most effective way to install. This is the best video on the topic!! I’m not at all comfortable with the “hinge and adhesive” method. Just seems to leave too many opportunities for error. The way he did it allows you to place it, step back and adjust if you need to. What is there to dislike about that? I got some big decals going on my Dodge and this is the only video that gives me confidence to do it myself and to absolute perfection. Blow dryer will work too in case you don’t have a heat gun.
@michaelfrick3687
2 жыл бұрын
Watched multiple examples on how to do it...your's was the best. As others have stated, having the decal wet allows for you to make the final fussy adjustments, if needed. Thank you.
@nickszewczyk6673
3 жыл бұрын
Wow! Thank you. Just bought decals for my Gladiator and was worried that I would screw up the installation. This video helped a ton!
@islandcowboy
Жыл бұрын
Hey! Thanks so much for the video! It helped me apply a fairly large decal onto my camper! Your method worked like a charm!
@thomasbradleyrealestateage9208
3 жыл бұрын
This helped a lot. Thank you Jeff!
@jasonsmith6508
2 жыл бұрын
Thanks for this. Just about to tackle my motorcycle and this is the best, quickest and most helpful video I’ve seen. Thanks again 👍
@ctzalman
Жыл бұрын
thank you for the tutorial. i tried the dry/hinge method and royally screwed up.. had a few air bubbles and even a small crease. this method was much easier and turned out 100% perfect.
@truthhurts228
2 жыл бұрын
Great video bro! You make it look easy! Thank you!
@jimschleitwiler6480
2 жыл бұрын
Great video. Best by far. Thanks for your help, Jeff.
@thedottyones5237
3 жыл бұрын
Thank you for sharing, this is the best decal-installation video
@pamil1923
3 жыл бұрын
Good job Jeff, Thank you.
@paulto2694
4 жыл бұрын
you do good job jeff, Thanks
@paulsharp6559
2 жыл бұрын
Thanks, really nice work.👍
@billystewart9366
5 жыл бұрын
Hey, it worked well, thanks!
@carlosllama9979
2 ай бұрын
Outstanding just like a pro thank you
@KLFaber
4 жыл бұрын
THAT'S EASY! I can do that. Thanks.
@Ryanthedrummer101
11 ай бұрын
I never knew you could use soapy water to install decals! I have a 36 inch I’m wanting to put on my back glass. Thank you!
@FearGod333_
2 жыл бұрын
Thank you. God bless you.
@gee1363
2 ай бұрын
Nice Jeff! Is it the same process for a large decal? Would like to install a decal that is four times the size. One that is for a Tacoma Trd Pro.
@ThePeepschamp40
3 ай бұрын
If u don't have a heat gun. How long do u have to wait before removing the transfer paper?
@HoneyBearLife
5 жыл бұрын
Good video. Just raise the volume next time
@julies3504
4 жыл бұрын
I like the idea of using the heat gun, or in my case a hair dryer, to make sure the decal is nice and dry. Thanks.
@mississippiprincess3421
3 жыл бұрын
Did the hair dryer work?
@julies3504
3 жыл бұрын
Yes.
@carlosvazquez8962
Жыл бұрын
That was a oem decal right? I'm about to install oem decals on tundra with your method
@elol6357
2 жыл бұрын
Thank you
@whitetrashandhellbound6905
2 ай бұрын
I have never done this with water/soap combo. I'm not a pro and have some fairly crooked decals on my ATV lol so, maybe the Wet Application is the way to go 🤟🇨🇦
@theredbeardreport
2 жыл бұрын
Appreciate you
@alfredoflorendo533
3 жыл бұрын
good job
@toastedcheesesandwiches
4 ай бұрын
I have some large lettering that goes the entire length of the car to install and am torn between using the wet or dry method. Half the videos say wet, half say dry.
@juansolis9409
5 жыл бұрын
you made it look great and easy, good job, sound not so good.
@jorgeanacleto6827
2 жыл бұрын
What is the solution being used ???
@justice4all32
10 ай бұрын
What the soap to water dilution?
@pedrofuentescruz7528
2 жыл бұрын
Wait so can you just add water and soap ??
@PottersWork
5 жыл бұрын
What kind of soap works best in the water? I’ve also heard to use windex...is that ok to use? Thanks!
@blastoi5e
4 жыл бұрын
never use windex
@PottersWork
4 жыл бұрын
@@blastoi5e, good to know, I watched another guy on here use it, but wasn't sure
@blastoi5e
4 жыл бұрын
@@PottersWork it destroys the adhesive i would honestly just buy a small bottle of rapidtac from amazon, i sometimes just use some water and dish soap about 60/40. tbh just using the hinge method and cleaning the service with some alcohol before hand would be a lot easier. and theres no need for a heatgun etc. just some masking tape and a decent squeegee.
@PottersWork
4 жыл бұрын
blastoi5e, thanks for the info and advice, it’s appreciated! I’ll pick up some rapidtac on amazon for sure.
@davidzyber7009
Жыл бұрын
@@PottersWork guy used soapy water in an empty Windex bottle👍
@_Moto215
3 жыл бұрын
Was that soapy water or just water that you sprayed? Thanks.
@jeffthebodypro7897
3 жыл бұрын
Soapy always
@keenokimancheta6973
6 ай бұрын
What just he spray? is that only water?
@speedstars9074
2 жыл бұрын
Is the heat gun step really necessary? I have a blow dryer but no way of taking it to the car lol
@BeardedGuitar
Жыл бұрын
I just did it yesterday without the heat gun and it worked perfectly...it was 85 or so degrees out which helped the peeling of the old decal as well...I just squeegeed a little bit extra and let the sun sit on it for a couple of minutes then started peeling and it worked perfectly.
@harishirsath
3 жыл бұрын
How sale this stickers
@isaacpalacios6901
4 жыл бұрын
Where did you buy the sticker?
@okstever
4 жыл бұрын
You can find a ton on etsy
@ajw6715
2 жыл бұрын
Is it water you use in the spray bottle?
@toastedcheesesandwiches
4 ай бұрын
Looks a bit soapy.
@shannano9414
3 жыл бұрын
Will this work on glass?
@jeffthebodypro7897
3 жыл бұрын
Yes
@mississippiprincess3421
3 жыл бұрын
Could I use a hair blow dryer 🤔
@farrelldavidcollins6189
Жыл бұрын
Cool but it’s crooked
@RookieStyles
3 жыл бұрын
"How to record videos with audio...the easy way"
@jeffthebodypro7897
3 жыл бұрын
Lol I’m at work
@managementmedia1190
3 жыл бұрын
Common sense method
@jaeaustin7362
2 жыл бұрын
Looks crooked 👀
@outpacer_ca
2 жыл бұрын
I own a sign shop and this is not the way the pros do it ! We never work wet, unless you're mounting a giant 4x8 print to an acrylic sign. moisture, no matter what, reduces the longevity of the graphic. most wet installation graphics will have a 2 year lifespan compared to 5 years if done dry. ofcourse, that depends on the media used.
@jeffthebodypro7897
2 жыл бұрын
Lol the directions from Toyota say apply wet
@bigfootswatching9986
Жыл бұрын
@@jeffthebodypro7897 I"m a Pro too.......do what work's best for you and not worry about what other's have to say. lol
@justice4all32
10 ай бұрын
And your video for dry installation for this application is? I would like to watch it.
@brucebernal65
2 жыл бұрын
Can't hear shit
@jefflovinfishin621
Жыл бұрын
Not remotely close to how a pro would do it lol. This is how an amateur would do it.
@jimjames6287
3 жыл бұрын
Sound was non-existent, so I didn't even make it past 10 seconds. Sad, too, since it looked like a good video otherwise.
@blastoi5e
4 жыл бұрын
absolute asinine way of putting on a simple decal.
@kennethross4117
3 жыл бұрын
Why asinine cause you didnt think of it first fucking asswipe
@blastoi5e
3 жыл бұрын
@@kennethross4117 There is no reason to apply a decal that small with a wet application. its going to take longer for it to adhere to the surface than if you just hinged it at the top and laid it down.
@garyjelsma8820
3 жыл бұрын
@@blastoi5e This is the correct method. If you want to take a shortcut, feel free. No need to be rude. This guy obviously does this at work.
@blastoi5e
3 жыл бұрын
@@garyjelsma8820 adding rapid tac for a small decal like that is worse than not using it at all lol. literally no reason to do it this way
Пікірлер: 72