Find the right Galfer brake lines for your ride! rvz.la/3E8HoXD
@debiddo.rorensu
Жыл бұрын
I have some of this on me Folding bike and for not using it for soo long it stiffens so much
@KB-yj5xp
Жыл бұрын
When I disconnect an old line I wrap some paper towel and elastic around the end to ensure no brake fluid drips out, brake fluid will destroy your paint if you get some on it.
@Motorcycle_Mike
Жыл бұрын
Love the extra content 👍🏻 More Patrick Garvin🔧⚙️🧰
@Kevwa51
Жыл бұрын
Another pro tip would be to twist the tails off the zip ties (if applicable to your bike) rather than cutting. Unless you’ve got a really nice small pair of side cutters, you can’t cut those close enough so there’s none sticking out, and they’re super sharp after you cut them. A pair of needle nose or linesman pliers and you can twist them off, if you can get right tight to the eyelet part of the zip tie it’ll twist off just inside that part and you won’t have any barb sticking out at all. Old electrician trick to keep your zip ties from becoming razor blades.
@johnnyblue4799
Жыл бұрын
All good, but I'd clean the dirt around the banjo bolts before removing them... 6:15
@20cent
Жыл бұрын
yeah I could see the sand falling into the caliper hole
@spongeaus
Жыл бұрын
yea i was cringing at him removing the rear ones and dust fell into the hole, i died a little inside
@lvvenky9973
Жыл бұрын
Fantastic ! Your meticulous procedure and skill makes it look deceptively easy.
@witchdoctor6502
Жыл бұрын
this is looks so easy, that I would fuck it up halfway trough :D
@kawabungah20
Жыл бұрын
Thanks for a nice DIY video with lots of good tips. I learned a lot! Using a beautiful bike as the subject makes us all jealous as well as informed! My own "add-on" tip that works for me (as extra insurance): use your camera to take a photo of each disconnect/connect point in the project before you disconnect at each end of the brake line. The photos can come in handy if you forget a detail for reassembly, including line routing throughout the machine. Check your photos before you secure all your lines and button down the final touches.
@paulv22
Жыл бұрын
Good video, but replacing one line at a time would make it easier to track which is which.
@joselouro3513
Жыл бұрын
Great video. Thanks a lot :) For dual cbs system (Honda BlackBird) the ideia is the same? Regards from Lisbon, Portugal
@deepideepinder967
Жыл бұрын
I am watching this and suddenly realise that my Vincent has drum brake and cable stopping power. The reason why I am watching is that I saw a machine from possibly the 1920s which can form the braided cable for sale at Malvern Showground
@sharagan
Жыл бұрын
Great vid! Thanks :)
@ehiggins7476
Жыл бұрын
Hey Patrick do you still have the Svartpien 701? What mods have you done to it?
@xorbe2
Жыл бұрын
You may need a special tool to activate the abs pump?
@seanylewl
Жыл бұрын
how do you clear the brake fluid out if you dont have one of those fancy pumps?
@spongeaus
Жыл бұрын
you get a bike air pump or compressed air
@Oh_Yeah_Bro
Жыл бұрын
Just put the hose around the nipple and pump the brakes, crack the bolt to get the fluid flowing and repeat until you get as much out as possible
Пікірлер: 27