The orange device is a a flasher relay circuit, not a load resistor. Different bikes/cars have different form factors and pinouts. I think most are in a box like the one you have, the flasher relay on my bike has a different form factor.
@CrusaderGeneral
Жыл бұрын
bro, this is a huge deal! Ive been racking my brain.. thanks a mill
@ACProductions77
Жыл бұрын
your welcome, still have more videos to come.
@CrusaderGeneral
Жыл бұрын
@@ACProductions77 let me tell you the whole story.. I have an H2 and doing a tail tidy. I actually cut off and tossed the stock blinkers, thinking I wasnt gonna need them. Then i discovered that to get access to the relay I would need to get under the dash.. So i yesterday I ordered the OEM blinkers that cost 150 each.. and just now found your vid, now i cancelled the order. And ordered the resistors.. 8 bucks vs 300+... you saved me some money bro :)
@kingretro9105
2 жыл бұрын
So if you don’t get that relay/ resistor the fuse will eventually blow? or will you just have very fast signals?
@ACProductions77
2 жыл бұрын
you just will have a fast flashing turn signal
@Salvador-ui3pj
Жыл бұрын
I like hyperfalshing,, it says to people im going to turn immediatelly and they have to walk away
@CrusaderGeneral
Жыл бұрын
Im not clear on this bro, are you putting the resistor in line on the positive wire, do you have a wiring diagram?
@ACProductions77
Жыл бұрын
go to min marker 5:00 it will show you how to install the resistor one end on + and other end on the -
@CrusaderGeneral
Жыл бұрын
@@ACProductions77 i see it now.. this is a parallel.. wonder what will happen if its wired inline. It will have a lot more resistance, and may be too slow.. in that case, a lower resister would be needed. Im gonna get a bunch of resisters to see what works best
@ACProductions77
Жыл бұрын
@@CrusaderGeneral as long as there is enough load to slow down the the flash rate on your turn signals. But if you’re able to locate the main turn signal relay box then you can just replace that with a led one as i show in the video and with that one it’s a one and done plus you can adjust the flash rate
@Truthsearcherforever777
2 ай бұрын
What if I got 25W6R8J? Will it work. I got zx6r 07
@ACProductions77
2 ай бұрын
it may not work the bigger 50 will work better
@bosanovaboy
Жыл бұрын
Question. Do you need 4 resistors for the 2 fronts and 2 backs?
@ACProductions77
Жыл бұрын
it depends on the bike , some need one at every light & others just need one for the pair & others you can have one main one for the whole bike.
@maellerapin3998
Жыл бұрын
Bonjour J’ai fait exactement la même chose mais lorsque je mets les résistances de la même façon mon clignotant s’arrête. Savez vous pourquoi?
@ACProductions77
Жыл бұрын
avez-vous installé des clignotants à led sur votre moto ou avez-vous encore les ampoules ordinaires d'origine ?
@ACProductions77
Жыл бұрын
Si le clignotant s'est arrêté lorsque vous appuyez sur le bouton, il se peut qu'il ait besoin d'une résistance de charge beaucoup plus élevée sur ce clignotant LED, vous devrez peut-être installer une charge plus élevée ou installer 2 résistances de charge sur la même ampoule de clignotant LED.
@maellerapin3998
Жыл бұрын
@@ACProductions77 j’ai installé des clignotants à led séquentiels.
@ACProductions77
Жыл бұрын
@@maellerapin3998 ok, alors vous devrez peut-être simplement installer des résistances de charge d'ampérage plus élevé avec les clignotants
@mohddohd7056
2 жыл бұрын
How about the rear LED signals? Do they need their own resistors?
@ACProductions77
2 жыл бұрын
on some bikes you will need a resistor on each one
@FirstnameLastName-sx8ls
Жыл бұрын
How much resistance did you use in total?
@ACProductions77
Жыл бұрын
40ohms
@joemartinez21024
2 жыл бұрын
Will that solve the issue I have with mine cuz all four turn signals blink
@ACProductions77
2 жыл бұрын
for yours you will need to replace the main turn signal load resistor with a led one this will allow you to control how fast they blink on all 4, normally located under the main rider seat its a small square black box
@anthonya824
2 жыл бұрын
If you look up “metric diode kit” you’ll find some tutorials. You could also replace you turn signal relay with one designed for low current LEDs. Either of those might be your solution, or both.
@MegaFoxey1
6 ай бұрын
You've got incandescent bulbs in 😂😂😂
@wrencher218
Жыл бұрын
Those are resistors. There is no positive/negative. They aren't diodes. Or are they?
@ACProductions77
Жыл бұрын
when i got those they can came with a diagram stating one to go to + & the other to -
@wrencher218
Жыл бұрын
@@ACProductions77 Yeah, as I did more research, I've found resistors, but with diode markings.
Пікірлер: 33