We are going over the steps to install new aftermarket lowering springs, panhard bar, and a jounce bumper kit for a 2012 Mustang GT.
IMPORTANT: A majority of suspension bolts should be discarded and replaced when replacing parts.
References:
performancepar...
1. Intro - 0:01
2. Step 1 (Mark Lower Control Arm Level) - 0:10
3. Step 2 (Loosen Lug Nuts) - 0:21
4. Step 3 (Lift Vehicle) - 0:31
5. Step 4 (Remove Wheel & Lug Nuts) - 0:44
6. Step 5 (Support Control Arm) - 0:51
7. Step 6 (Remove Upper Mount Nuts) - 1:04
8. Step 7 (Remove Speed Sensor Support) - 1:25
9. Step 8 (Remove Brake Hose Bracket Bolt) - 1:37
10. Step 9 (Remove Stabilizer Bar Upper Nut) - 1:49
11. Step 10 (Reposition Stabilizer Bar) - 2:05
12. Step 11 (Remove Control Arm Support) - 2:16
13. Step 12 (Remove Strut Flag Nuts) - 2:29
14. Step 13 (Remove Strut Bolts) - 2:46
15. Step 14 (Remove Strut) - 3:10
16. Step 15 (Compress Strut Spring) - 3:44
17. Step 16 (Remove Upper Mount Assembly) - 4:33
18. Step 17 (Remove Strut Spring) - 4:48
19. Step 18 (Remove Spring Compressor) - 4:59
20. Step 19 (Clean Strut) - 5:24
21. Step 20 (Install Caliper/Guide Pin Bolts) - 8:07
22. Step 21 (Replace Jounce Bumper) - 6:12
23. Step 22 (Compress New Spring) - 6:41
24. Step 23 (Install Upper Mount Assembly) - 6:59
25. Step 24 (Install / Position Strut) - 8:02
26. Step 25 (Install Strut Bolts) - 8:38
27. Step 26 (Support Control Arm) - 8:53
28. Step 27 (Install Strut Flag Nuts) - 9:01
29. Step 28 (Torque Strut Nuts/Bolts) - 9:25
30. Step 29 (Install Speed Sensor Support) - 9:42
31. Step 30 (Install Brake Hose Bracket) - 9:54
32. Step 31 (Torque Brake Hose Bracket) - 10:10
33. Step 32 (Install Upper Mount Nuts) - 18:00
34. Step 33 (Torque Upper Mount Nuts) - 10:32
35. Step 34 (Reposition Stabilizer Bar) - 10:51
36. Step 35 (Install Stabilizer Bar Upper Nut) - 11:03
37. Step 36 (Torque Stabilizer Bar Upper Nut) - 11:27
38. Step 37 (Remove Control Arm Support) - 11:48
39. Step 38 (Install Wheel & Lug Nuts) - 11:56
40. Step 39 (Lift Vehicle) - 12:04
41. Step 40 (Torque Lug Nuts) - 12:12
42. Step 41 (Lift Rear End) - 12:38
43. Step 42 (Remove Rear Wheels) - 12:47
44. Step 43 (Remove Stabilizer Bar Link Bolts) - 12:53
45. Step 44 (Remove Panhard Rod Bolts) - 13:19
46. Step 45 (Remove Panhard Rod) - 13:47
47. Step 46 (Adjust Panhard Rod) - 14:07
48. Step 47 (Install Grease Fittings) - 14:33
49. Step 48 (Install Panhard Rod/Bolts) - 15:07
50. Step 49 (Torque Panhard Rod Bolts) - 15:46
51. Step 50 (Remove Shock Absorber Lower Bolts) - 15:58
52. Step 51 (Lower Rear Axle) - 16:25
53. Step 52 (Remove Rear Springs) - 16:31
54. Step 53 (Install Rear Springs) - 16:41
55. Step 54 (Remove Rear Jounce Bumpers) - 17:12
56. Step 55 (Install Rear Jounce Bumpers) - 17:29
57. Step 56 (Lift Rear End) - 17:50
58. Step 57 (Install Shock Absorber Lower Bolts) - 18:06
59. Step 58 (Torque Shock Absorber Lower Bolts) - 18:31
60. Step 59 (Install Stabilizer Bar Link Bolts) - 18:41
61. Step 60 (Torque Stabilizer Bar Link Bolts) - 19:16
62. Step 61 (Install Rear Wheels) - 19:23
63. Step 62 (Lower Vehicle) - 19:44
64. Step 63 (Torque Lug Nuts) - 19:57
65. Step 64 (Adjust Panhard Rod) - 20:20
66. Before / After Shots - 21:08
67. Test Drive - 21:25
Suspension Parts:
SR Performance Lowering Springs - www.americanmu...
Panhard Bar - www.americanmu...
Jounce Bumper Kit - www.americanmu...
Products Used:
This video contains affiliate links for which I may receive compensation.
Trim Removal Tool Set - amzn.to/3hRQA8j
Torque Wrench (20-200 in-lb) - amzn.to/3CriqBH
2-Piece Ruler Set - amzn.to/3sV28Om
Paint Marker Pens - amzn.to/3Xv8fWZ
Tools:
Torque Wrenches (Req: 15-166 ft-lb)
Spring Compressor Kit
1/2" Socket Wrench
3/8" Socket Wrench
1/4" Socket Wrench
1/2" Breaker Bar
21mm Socket
19mm Socket
10mm Socket
13mm Socket
15mm Socket
18mm Socket
8mm Wrench
17mm Wrench
25mm Wrench
27mm Wrench
Grease Gun
Semi-Permanent Threadlock
Ruler
Shop Towels
Soap and Water Solution
Wire Brush
Trim Removal Tool Set
Paint Marker Pen (Optional)
Pry Bar
Jack Stands
Jack
#LoweringSprings
Disclaimer: Content produced from Mcgurr Entertainment is for entertainment purposes only. This information is not endorsed by any agency/company (such as Ford) and is intended as an entertainment. Mcgurr Entertainment assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. All content on KZitem is provided in good faith, however we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability or completeness of any information on KZitem. Use this information at your own risk.
Негізгі бет How to Install Lowering Springs and Panhard Bar for S197 Mustangs (2005-2014)
No video
Пікірлер: 71