🔰Corner Shelves • 🔥 Cómo Hacer REPISAS d...
✅ If you are going to do some work for PLADUR, and you are going to choose to hire a company to do it, I have created a short guide to help you analyze the budget and avoid common deceptions in the sector. Head over to www.tutorialcre... to download it.
In this video you will see how to install a PLADUR hatch.
These hatches are very comfortable for when you want to leave something hidden, but you will need access. Examples: stopcocks for water, electricity connection boxes and even, if you have enough space between the false plasterboard ceiling and the slab, you put a large one and it is good for storing things in that hole.
The hatch is made up of aluminum profiles with a 12.5 mm anti-humidity PLADUR plate, and two or more click closures. The two frames of the hatch are made up of four profiles solidly joined together by means of a special procedure. The hatch is supplied with one or more safety cables and a hooking carabiner that must be closed after each use, in order to avoid accidents. The installation of the hatch on walls or ceilings is immediate and easy.
Between the frame and the hatch there is a 1.75mm gap that contains a profiled gasket that prevents the passage of light between the frame and the hatch. The invisible click locks open the gate only by exerting pressure.
🔴Links to materials / tools that I get online
- Screwdriver = amzn.to/3r1L2tH
-Red light self-leveling laser = amzn.to/2Lw66ty
-Green light self-leveling laser = amzn.to/3nphzIr
-Set of two scissors = amzn.to/38qVg0Z
- Bit holder with depth stop = amzn.to/2L9Xmt2
-fischer Sx / UX / (Briefcase of 290 Tacos) = amzn.to/3okzVvz
Video transcript:
We are going to place a small plasterboard hatch.
With a magnet we will check where the profiles pass us, thus avoiding having to cut it.
If the hatch were large, there would be no choice but to cut a profile.
In this case we will leave a separation of 10 cm from the wall.
We will use the cap to mark a square.
We measure the frame by the outer area of the overhang. In this case we have 20cm.
Now we mark from the square that we made 20cm on each side.
We mark the lines.
In this case, to avoid dirtying, we will fasten a box on the wall, so that when cutting, the dust falls inside.
With a pointed saw we cut along the lines.
Now we place the frame. In this case, it will enter us a little bit because the ceiling lowers a little from the slab.
I usually always place the frame so that when opening the cover lowers towards the wall.
When screwing the sides, we will do it in the centers because the corners are usually reinforced and the screw does not fit well.
They usually bring some gummies that are put on the screws so that when you put your hand you do not hurt yourself.
If you are still there and you are not subscribed, run, Subscribe !!
With a little paste we give the screws and the crack that remains between the plate and the hatch.
Once dry, if needed, give the screws another coat of paste.
When drying we pass a sandpaper and ready to paint.
If you are going to do some work for PLADUR, and you are going to choose to hire a company to do it, I have created a short guide to help you analyze the budget and avoid common deceptions in the sector.
Head over to www.tutorialcre... to download it.
If you liked this video, don't forget to click I LIKE it and share it with your friends.
Do you want to find out every time I upload a new video of crafts, tricks, decorating ideas, inventions and some other interesting and fun things? Well, don't forget to subscribe to my channel :-D
Негізгі бет 🔥 How to Install PLADUR Hatch ✅ Registration for False CEILINGS and Walls (Drywall)
Пікірлер: 33