Every video I've seen on KZitem about these recessed lights always used attic access. I'm glad you addressed a real problem instead of going the easy way. What I most liked was the crown molding Idea. You're probably the most blunt and honest electrician on this platform. "To do this, you're probability going to have to make a bunch of holes. Better to do a couple of patches than take a chance on wrecking the house." FINALLY! And you seem like someone who has been teaching people (or confused DIYers) for quite a few years.
@sanjivoberoi5361
4 ай бұрын
So far every other video I have seen missed the point that novices like me need detailed instructions with options. Thank you for a great instructional and useful video.
@localone1597
7 ай бұрын
Thanks so much for your video. Its about time someone shows a tougher insulation. Everyone else shows either attic access or will not show the full install when there's a hard ceiling and no access above. Thank you!
@kgj08
5 күн бұрын
Beautiful video.. absolutely fantastic. I've watched about 5 of these so far and this is by far the best one and answers lots of questions unanswered by the others. THANK YOU!
@andrewshoultz9844
Жыл бұрын
Thanks for the video. I just did a job for my father and used 1.5 flexible PVC pipe in one light hole and used a snake through the PVC pipe to get directly through to the other light hole and then pull the wire back to the starting hole. Worked for me.
@abdulamaly7108
12 күн бұрын
That’s nice! I planned to do that in my kitchen, thank you for demonstrating and very educational.
@alfaun
Жыл бұрын
Thank you for this video and it’s visuals. This is the first video that I have found that specifically addresses my situation. I’ve wanted to install this type of lights in my ground floor kitchen, located in a two story townhouse with the ceiling directly adhered to the joists. This video clearly explained the process necessary to accomplish this project. Keep up the good work and hope to see more videos in the future.
@WorkinwithWolkon
Жыл бұрын
Glad I could help!
@parkerkouse837
Жыл бұрын
I used a flex bit😂 I died when you said you better have home insurance😂 I got really lucky and the project turned out great, loved this video though you really are the only one who has a made a video with truly no attic access
@Geeleo2282
Жыл бұрын
Thank you! You just saved my life! Seems like every video had an attic above. I have a 2-story home and am doing this on the first level in my kitchen. Your demonstration was perfect as I have ceiling joists dividing my pot light holes. Your video has reassured me that I can move forward.
@noyzizi
Жыл бұрын
I've watched countless videos like this before attempting my project and this is by far and away the best and last video I'm watching before I start. Thank you
@WorkinwithWolkon
Жыл бұрын
Thanks, good luck!
@laszlovass7326
Жыл бұрын
I was thinking about doing this upgrade in one of my rentals. Then the tenants 4 year old flooded the upstairs bath and the parents failed to notify me for 7 hours, soaking the ceiling and carpet. It's now easier with the drywall ruined and removed. Thanks tenant. I also appreciate the lack of money to repair their 10k in damages. I am really enjoying doing this upgrade to lighting for them with the 2k in deposit. Only costing me 8 k.
@inkman002
Жыл бұрын
Wow, that sucks.
@that_random_dad
Жыл бұрын
This video was so helpful! I installed 5 pot lights today using your system to be sure no pipes or wires were damaged. Thank you!
@docdoctme
2 ай бұрын
I love your detailed instructions along with the visuals. Thank you for sharing your talent.
@jmorehed
Жыл бұрын
I’ve been watching so many videos and this one is by far the best one. Thank you! Thank you! Thank you!!! God bless you!
@MP-wb5yd
Жыл бұрын
Clearest tutorial on the subject by far
@Dr00_
Жыл бұрын
You can do a video on installing a bathroom exhaust fan. I believe you will explain the process proficiently. Additionally, I enjoy how you offer possible situations that one might encounter.
@WorkinwithWolkon
Жыл бұрын
Thanks I shall do this eventually!
@unkulunkulu8842
Жыл бұрын
By far the best recessed lighting installation video on KZitem. Appreciate you taking the time to set this up -- helped me out a ton!
@fulanacubana
6 ай бұрын
Thank you so much for this information. Best video I've come across so far on how yo
@valerielarue3586
6 ай бұрын
Great video with very clear instructions. Thank you!!
@SraTacoMal
Жыл бұрын
Can we take a moment to appreciate the "You better have home insurance"?
@zachfischer3148
Жыл бұрын
I ended up getting lucky putting in 10 pot lights in my living room with no attic access. The home was built with open trusses so made fishing the wire very easy and was able to pull power from an old uncentered ceiling fan for the pot lights and the old entry light was used to center a ceiling fan. Love the video and gives a great visualization for not having open trusses
@rpvs
10 ай бұрын
This is the best diy video I have seen. Extremely well done, thank you!
@joeweatlu5169
9 ай бұрын
I did a very similar job in my kitchen using 6" wafer lights. Similar to yours, there was an existing fixture in the center, and installed 4 wafer lights in the same positions as yours. The J-box in the center had three cables connected to it. Rather than putting in a blank plate, I made the existing connections in another junction box, which I just placed above the ceiling along with the driver for an additional wafer light where the original fixture was. This way the junction box is still accessible and code compliant, and no need for a blank plate. Nothing wrong with having an extra light in the center.
@tutuuo
8 ай бұрын
An actual video. Thanks man. All of the other videos are pre done.
@alex-650
Жыл бұрын
Excellent practical coverage of various real world obstacles and solutions for wiring. A welcome relief from most other folks who un-helpfully focus on the pretty lights and silly unboxing.
@kchen032
Жыл бұрын
The visualization of the joints above the ceiling is very helpful for a novice like me. Thanks! Can I just run the wire across the top of joists so no need to drill holes on them?
@jimwest1629
4 ай бұрын
GREAT JOB! I love this video. I love DIY projects and recessed lighting has always been a bit of a mystery for me. You made it look easy. Now off to the store to buy lights… but first… I will be calling my insurance company to see if I have enough coverage.
@bobarino
Жыл бұрын
Thank you for this video. THE best video on this subject I have found. Very good explanation of every step and what to expect for my upcoming recessed led lighting project. THANK You for all your hard work!
@anonimoporsiempre6033
Жыл бұрын
Thank you very much for taking the time to show us how to get it done. I really appreciante. January-13-2023 9:01am. 🍑🇺🇸👍🏼👍🏼🤝
@Blaeqon
Жыл бұрын
The visualization this amazing and so helpful! Thank you!
@rnsgames599
4 ай бұрын
I applaud you, immaculate video my guy💯
@hospitaladministrator3359
Жыл бұрын
Underrated video. Good instruction. Thank you
@ajmorales3595
Жыл бұрын
Thanks for the demonstration. You cleared many doubts.
@relaxingrealityescape5336
10 ай бұрын
So with attic access there’s no need to drill right? You can just run over the rafters?
@wadest1163
6 ай бұрын
Very good video. I'm trying to do this on a first floor with plaster and lathe, no space between. I think I'm going to pull your floor up.
@JohnNeville617
Жыл бұрын
This video was super helpful to visualize the process! I am not actually installing lighting but I was going to hire an electrician to run some cat6 and this is making me much more comfortable with the idea of doing it myself.
@rhkips
Жыл бұрын
Vaulted/cathedral ceilings, 2x8 joists with 24" on center spacing, and blown-in insulation... Time to make a mess! LOL Awesome video, thank you! I think I'll either need to make extra holes, or get a really long spade bit. :)
@sais9221
Жыл бұрын
Thanks! I love your format. I plan to do this in our living room and kitchen in near future. Subbed
@jflo7674
2 жыл бұрын
Talented and handsome young man. ☺
@adammocaby2636
2 жыл бұрын
Thank you for these tips you've been giving. Really happy to see you uploading more.
@danilo352
Жыл бұрын
Hint: hold your drill up for 5-10 seconds after making each hole. The dust will settle into the dust catcher and you’ll be amazed how little cleaning needs to be done at the end!
@cartor7962
Жыл бұрын
Excellent visuals and teaching!
@fshussain_gaming8063
Жыл бұрын
Thanks so much for this video. It is so detailed with such clear visibility.
@WorkinwithWolkon
Жыл бұрын
Glad it was helpful!
@BigWillBx
Жыл бұрын
Excellent video, exactly what I was looking for to clarify some things for me! Thank you!
@mae2759
Жыл бұрын
Good video. I have a somewhat similar situation. One switch in the room controls an outlet on the other side of the room and there is no overhead lighting. I thought about putting pot lights in, but I'd have to tear out a ton of drywall like you showed, and the switch situation would be very dicey. Probably will just have to live with my lame switched outlet. haha. Also, in your video, if you are putting a pot light where the existing overhead light box is, you can start your wiring there and go around the room and you wouldn't have to mess with the switch. I think most people would want a light in the middle of their room, so that would make things easier than having to rip the box out.
@bennybischoff4913
Жыл бұрын
Excellent! Thank you for taking the time to create this video. Really helpful.
@SeanGilchrist
9 ай бұрын
Excellent teaching! Well done.
@RM5044
Жыл бұрын
Such a helpful video. Very detailed and easy to follow instructions.
@WorkinwithWolkon
Жыл бұрын
Glad it was helpful!
@markf6743
8 ай бұрын
Thank you for your well-thought video. :)
@mohammadabid1222
Жыл бұрын
I love the video the problem my house 1926 lath and plaster so frustrating to drill holes and repair damage. Not only that but also crack appear when I started drilling and now I am stuck
@Jack-rn2im
Жыл бұрын
How abt open the underlay from second floor?
@clintw8173
2 ай бұрын
Nice video!
@riffmeisterkl
Жыл бұрын
Luckily in Australia we use those posistrut joists that have steel trusses/chords in between two pieces of timber to form a joist - lots of empty space to fish things through.
@SraTacoMal
Жыл бұрын
Me: 👁️👄👁️ The pipes I miraculously missed by less than a centimeter when drilling a 3.5" hole in the ceiling: "'Sup baby girl"
@seaofrage
7 ай бұрын
Finally a video about the real shit haha. All the other ones ive seen have it so easy with no need to go through joists.
@SurfDetector
Жыл бұрын
The radius of the angled probe that you use in the ceiling prior to drilling your holes should be the same radius as your cutout. This sort of probe is easily made with a piece of fish tape bent at a 90 degree angle. In addition to looking for the presence of joists and ducts you should not be cutting into the strapping that your drywall is attached to.
@Captivateitmedia
Жыл бұрын
Awesome vid and very detailed. Most appreciated. :)
@alphayankee1066
Жыл бұрын
Very helpful video thanks!
@Googaliemoogalie
Жыл бұрын
My tip would be that when you drill each hole and to check if there's anything in the way, take out your phone, turn on camera with flash in video mode and stick it in there and look around and record a video to see what's up there.
@ggsholdings7225
Жыл бұрын
Really good explanation bro!
@diwu1877
20 күн бұрын
why do you need to drill holes through those 2x8 boards? I see there are gaps above, just wire through the top gap?
@TenTwennyDollaBills
7 ай бұрын
NEC 314.23(A): "Boxes, conduit bodies, and fittings shall be securely fastened in place." For a no attic install, I think it's best to put these things right next to joists and get a long bit and fasten the boxes through the hole.
@mikerck
Жыл бұрын
This was so helpful thank you!
@jonengert-v4o
24 күн бұрын
What if there is batt insulation between the drywall and roof decking?
@hcdwinter6482
Жыл бұрын
I would try the Hole saw centring device for enlarging holes in ceiling, quick and easy tool to use , Lots of video’s on KZitem 👍🏻
@bensir6778
Жыл бұрын
Im trying to put recess lighting into an old house - but I want to keep the main light as well and possibly add a dual lightswitch - one switch turns on existing light and second turns on new recess lighting. Never done anything like this before but I fixed up my car (mechanical) after watching a few videos just fine, so I think I can handle this. Could you make a video about adding a dual light switch or even how to add a new switch to a new location. like on the otherside of the hall so I have two switches for the same light
@Heatherbailey1
Жыл бұрын
I’m interested in the same thing- how to add the switch(es) if there is no preexisting switch wire to use. I’m remodeling a room that will have canned lights on one switch (probably a dimmer) and a ceiling fan on a second switch. And both need to be controlled from each side of the room.
@foley123456789
4 ай бұрын
Where do I get a dust bowl like this please I've looked everywhere lol 😆 all I find is plastic spring ones and there rubbish
@robertsroberts4327
8 ай бұрын
Awesome
@ASolangeM
Жыл бұрын
OMG can you make a video like this for replacing the fluorescent lights in a drop ceiling with some nice smart recessed lights?!
@jasonpereira1637
Жыл бұрын
Very helpful will subscribe
@youtubesucks5007
10 ай бұрын
If there isn't insulation, you can use a small USB camera to look in the bay to make sure you're not drilling into anything with only a small hole to patch.
@keithworrell47
10 ай бұрын
What a great video
@nkraemer
Жыл бұрын
Thank you.
@robb3346
5 ай бұрын
How do I connect the red wire from the existing light/fan?
@Mo-P
Жыл бұрын
I wish I would've seen this before I bought a flexbit! Thankfully I haven't used it yet!!
@WorkinwithWolkon
Жыл бұрын
You can use it but you just have to be extremely cautious and understand the risk. If there’s a bathroom above the ceiling you’re working in then definitely don’t do it. Also it’s very easy to have the bit come out somewhere it shouldn’t lol
@Mo-P
Жыл бұрын
@@WorkinwithWolkon I appreciate that! I have terrible luck and even though there's no bathroom, I would definitely hit something! I have to scrape the popcorn off the ceiling anyway, so adding a few holes won't kill me (there's no asbestos) 😁. Also, thank you for making a video that actually explains what to do without access. Every other one I've found is "we have no access..... but there's a gap that we can run the wire through, so it should be easy."
@brabus343
6 ай бұрын
I wanna see a magic way to pass the wire through studs having a 4inch hole, that's why iam here 😅
@mowburnt
Жыл бұрын
Great video, really helpful but look after those lungs and eyes with some ppe
@squirts1
Жыл бұрын
I'm not sure hiding wires behind crown moulding is legal. Also, as far as being able to see into the next "joist space" all you need to do is drill through one joist, then stick an inspection camera into the hole and look around. You can get endoscopes for like 30$... Furthermore... It's actually very easy to tell if you've contacted something that isn't the wood you are trying to drill through with cable bits (long flexible drill bits). In addition to that, it's generally pretty easy to get a good idea of where your plumbing and air ducts are without cutting holes.
@WorkinwithWolkon
Жыл бұрын
It’s legal where I am to use crown moulding but obviously local code can differ. You need to remember this video is made for DIYers. They probably aren’t going to want to buy an endoscope. I use flexibits all the time for the exact reasons you mentioned but a DIYer will 100% drill through something they shouldn’t have lol
@squirts1
Жыл бұрын
@@WorkinwithWolkon a 30-60$ inspection camera pays for itself in time and money very quickly for diy projects. Probably in this project alone. No need to patch a hole, buy paint and drywall repair supplies, etc.
@ibaan
9 ай бұрын
Great video and helps me a lot. Quick question on the hexagon ceiling box opening. Can you patch that opening or get some cover for it?
@muhammadashfaq4419
Жыл бұрын
Installation of led SMD light with 1 way switch installation
@EliasRodriguez123
Жыл бұрын
Great video
@ayrdrie9118
Жыл бұрын
So is that "to code" to have exposed wires running parallel to the ceiling joists? I thought wires couldn't be exposed incase someone was ever to drill through the ceiling and puncture it. I understand you could staple it to the ceiling joist but maybe it would be difficult to do it you don't have attic access. I mean if I do this to my home and stay forever I would know not to ever puncture my ceiling in those areas but if I sold the home the next owner would not. So long story short, is it to code?
@steve9503
Жыл бұрын
I want to install four pot lights in the kitchen with no attic access and found your video invaluable. I can use the existing fixture as the feed to the new pot lights since it's already switched. As you explained, the octagon box where the old fixture was located can be used as a junction box. After making the connections to the pot lights does this "junction box" have to be accessible? I'd like to cover it up completely by repairing the drywall. I don't want to have some sort of cover plate in the center of the ceiling where the old fixture was.
@WorkinwithWolkon
Жыл бұрын
Unfortunately the junction box will need to be accessible if you want to meet code. In my area a lot of the time we will shove the box into the ceiling and put a pot light below as the box is considered accessible by means of pulling the potlight down Of course this may not work with the layout that you want but it is an option
@syedqurbanzada3657
10 ай бұрын
You can definitely see it by putting your phone up there and take a picture 😂
@broganboydmusic7561
Жыл бұрын
I dont have an existing light to use as my switch line. I’ve successfully drilled through all the joists and have all the lights connected. I just need to somehow get the Romex through the corner of the wall and ceiling and feed it down the wall to my switch box. The wall is behind shelves as well….sooo my brain cant solve it. Someone please help.
@davidlaw2595
Жыл бұрын
Where did the original light fixture wires go? Where the leds get it’s power? From the original wires where the light bulb is?
@grousgrek6560
Жыл бұрын
That was a great detailed video ! What size was that drill bit you used through the joists ?
@WorkinwithWolkon
Жыл бұрын
Thanks! 3/4” probably
@misssilentstorm4281
Жыл бұрын
What do you do if that main hole in the middle is a ceiling fan and you want to reinstall it after you’ve installed your recessed lighting? Will the ceiling fan have a junction box? And do I just wire from that box to one of the holes, and so on?
@misssilentstorm4281
Жыл бұрын
Also - very helpful video!!
@sanketpatel209
Жыл бұрын
What to do if there is duct lines going or water hose ?
@chuethao385
Жыл бұрын
you should stick a inspection camera up there to see if there's any pipe up there a lot of DIY never follow codes you wouldn't want to cut a hole and suddenly cut a water pipe and using flex auger is easier your journeyman and foreman don't like it if you have too many holes on ceiling especially one that fits a fist size
@glibsonoran
Жыл бұрын
Would a right angle drill with maybe a shorter bit work for drilling the joists?
@WorkinwithWolkon
Жыл бұрын
Absolutely!
@UsakiaMC
Жыл бұрын
Maybe a stupid question, but if you can feel around all of the joists, if you can get above the joist, why wouldn't you just run the wire above the joist if you can reach over all of them rather than drilling through the joist?
@WorkinwithWolkon
Жыл бұрын
You would absolutely run your wires over top the joists if it was an attic or drop ceiling. This video was made specifically for when that isn’t the case, as in there’s a subfloor on top of the joists so you can’t go over. I probably should have put something on top for demonstration purposes to convey that better.
@Unknownedp1
Жыл бұрын
All KZitem video I saw was how to install them. I know that. My question is how u give them power. Like what’s the power source
@WorkinwithWolkon
Жыл бұрын
That’s shown in the video
@VworksArt
Жыл бұрын
Is there any reason that you can't use the center junction as a light as well?
@WorkinwithWolkon
Жыл бұрын
You absolutely can
@VworksArt
Жыл бұрын
@@WorkinwithWolkon much appreciated. Ideally I want to use the center light as a junction to branch to the others, binding them to the switch so thats perfect. Thanks for the information!
@supermotosize
5 ай бұрын
Right angle drill...
@sarahcunningham8
Жыл бұрын
I don't know if you get a commission on the links but the retrofit is now unavailable if you want to change it out😊
@mustanggt500doh6
10 ай бұрын
Why not just run the wire over the joist when fishing it so you don’t have to drill?
@thisguy5835
6 ай бұрын
This is a demonstration for if there is no access above the joist. If it’s a 2 story home sometimes the just is flush to the second level and to the sheet rock for first level ceiling with no space between so the only possible way is to drill
@raulbarasa5855
Жыл бұрын
Full send 😂
@Kun373
Жыл бұрын
u should wear a glasses
@SraTacoMal
Жыл бұрын
How ⌨️ to ⌨️ patch ⌨️ popcorn ⌨️ ceilings
@ONWOTE
2 жыл бұрын
hello, any chance for us to work together? we would like to sponsor you a set of security camera system to you to install and review. i had emailed you the details of business proposal, hope can hear from you an move forward.
Пікірлер: 131