Thanks your video got me to do something similar, but you could have use the first 2 right pins on the 6 pin block right underneath the contact sensor to connect your switch wires and change J1 to on and J2 ( 4 jumpers to the right of where you got power from ) to off to program the switch to an On / Off function.
@indrin401
3 жыл бұрын
Hi, did you also have to change the "Gate Input Toggle Select",ie. 1110*# ?
@HomeDIY5Nat12Ken13Go9
3 жыл бұрын
Thank you for the feedback. I did not make any other changes except for the ones in the video.
@antbran1916
2 жыл бұрын
I was thinking the same thing. The unit comes with this function.
@mathsacademy9484
4 жыл бұрын
That is brilliant thinking. Continuous improvement at its best. NO MORE USING MAGNET BUT USE A REMOTE AT A DISTANCE. Thank you so much.
@HomeDIY5Nat12Ken13Go9
4 жыл бұрын
Cool, thanks
@quasiemkherekar3930
3 жыл бұрын
No need to solder wires on the contact there is a input for a remote receiver it is the switch input then you remove jumper 2.3 and 4
@albertomiguelmiguel-uh2ow
Жыл бұрын
Gosto muito dos teus vídeos mas agradeceria que mostra como configurar desde o início passo a passo, colocando os jamper na central
@Mister_Majesty
3 жыл бұрын
My Druid Energizer is showing Druid 13 on display, fence alarm is past event and fence mode is off. It was on Good earlier today but now is showing Druid 13. What do I need to do?
@ernestonaruclaudio
3 жыл бұрын
Quero um vídeo que ensinam como configurar
@btecnologia9818
2 жыл бұрын
My energizer Wizord 2I is flashing alarm permanently. How to troubleshoot or remove the fault?
@HomeDIY5Nat12Ken13Go9
2 жыл бұрын
Good day, please consult your local electrician. I cannot technically assist you on this issue. I'm sorry.
@garethnkem1091
3 жыл бұрын
Please how can I mk this connection for a wizard 4 energizer my?
@HomeDIY5Nat12Ken13Go9
3 жыл бұрын
Unfortunately, I do not know how it looks like. All the best in getting assistance.
@quasiemkherekar3930
3 жыл бұрын
Wire your receiver to the switch input and remove jumper 2,3 and 4
@izanpretorius81
3 жыл бұрын
Could have used a better soundtrack... but thanks for the idea
@NRC073
Жыл бұрын
As clear as a brick wall....
@cookingqueen
4 жыл бұрын
Use of a magnet is so backward especially this time of AI.
@HomeDIY5Nat12Ken13Go9
4 жыл бұрын
Thank you
@robertdacosta3499
3 жыл бұрын
Hope you not an installer , that is so incorrect the way it's installed , not sure how you got the CoC for that . Using the switch connection on the PCB and removing j2 would be the ideal solution and what it was also intended for . 🤔🤔😕
@HomeDIY5Nat12Ken13Go9
3 жыл бұрын
Please share the correct way of installation.
@konraddorfling
3 жыл бұрын
@@HomeDIY5Nat12Ken13Go9 left of the strobe light terminals is a multi-purpose terminal (yours is bridged out in the video) that can be used for a Gate, Remote On/Off, Panic or Lo & Hi Voltage switch. The function can be changed using the jumpers 1 & 2 further left on the PCB. Check the installer's manual for the jumper combinations, but in short, remove J2 and keep J1 jumper in place as Robert said.
@indrin401
3 жыл бұрын
@@konraddorfling - from the video clip - is J2 considered to already be in a off state and you just have to move J1 down? Issue I'm having is pressing the remote goes ON-GATE-OFF-GATE-ON, not sure if the J2 should be completely removed or do I need to use a keypad to change "Gate Input Toggle Select",ie. 1110*# ?
Пікірлер: 23