Hi , before fitting my Heed bars , l watched your video and that helped me alot , especially having someone hold the bars when fitting them ! Well Done ! Thanks . Steve .
@kentrota5988
Жыл бұрын
Hi, just wanted to say thanks for the video. Installed the Heed bars today on my 2020 1050 XT and your video came in handy even though I had the instructions. Also no spacers needed if you have factory lowers👍
@iberiano01
2 жыл бұрын
Good jobs and thanks for sharing.
@achilleas995
2 жыл бұрын
Hi and thanks a lot for the video. I have the same motorbike. I have also add the same engine guard but i was needed extra force for installing it. Anyway once again thanks for sharing!!!
@m.k.6082
Жыл бұрын
Thanks so much for this Video! Helped me to get this done! 👍
@doc650adventures
2 жыл бұрын
Great video! I just purchased a 2022 V-Strom 1050XT Adventure with the lower crash bars and the Heed Upper bars might be the solution I am looking for. You have had them for awhile now, do you still like them and have they caused any issues? Thanks again for a great video! Cheers!
@kers2008
2 жыл бұрын
Thanks 😀 I still have them on, but they give a lot of extra wind noise on the highway. I hvae considered to remove them when I'm using the bike on a daily basis and just mount them again when going on long road trips.
@2wheeledwillie395
2 жыл бұрын
Hi, great video 👍 noticed that you have a belly pan fitted.. Did you fit that yourself and is it a suzuki one? Cheers
@kers2008
2 жыл бұрын
Thanks :-) The engine protection plate is from Hepco & Becker and I fitted it myself www.hepco-becker.de/en/engine-protection-plate-aluminium-for-original-engine-guard-for-suzuki-v-strom-1050-xt-2020.html
@CaptLawrence
Жыл бұрын
This is great thanks a million dude
@Rumpelstiltskin999
11 ай бұрын
I instaled them but i have some vibration (not to much).Going to put today ruber washer to reduce vibration .i have questions ,did you must remove them when you change sparks and air filter?
@chrismatthews1961
2 жыл бұрын
Hi. Great vid. I plan on fitting some to my 1050. What torque settings did you use to tighten the engine bolts?? Thanks👍👍
@nickharker6299
2 жыл бұрын
Hi I have just fitted a set of these to my 1050xt and like you I used the bolts that came with the herd kit but the original spacers as Also have the lower engine guard bars. Have you had any issues since doing this ? I’m finding I have a little more engine vibration? Could the longer bolts maybe alter the engine alignment if not used with spacers supplied by heed? I may take one out and measure it against the original bolt measure how much longer it is. If I then take away the depth of the heed mounting point, my thought is that it should then give the same thread depth as original bolt? Or am I over thinking it?
@jimdoolan2277
2 жыл бұрын
Great video my man love to get a set for my v Strom xt 1050 wonder if i can get them shipped to new Zealand 🇳🇿 Great bike love my one just hit 70000 kms on my one 😀 👍
@taol3944
Жыл бұрын
nice video, but when it comes to the air filter changes, do we have to dismantle everything? We need to remove the fairing and petrol tank to get access to air filter on this on right ?
@CaptLawrence
Жыл бұрын
Yes you are correct this makes basic maintenance a huge pain in the butt. However makes offroad riding alot more fun because you can be dumb without too many consequences
@vincenzoscarpello2476
2 жыл бұрын
Sorry, I don't understand from the video: when you inserted the spacers, did you remove the exsisting ones, or not? And did you inserte the spacers on both the right and left, on both sides?
@kers2008
2 жыл бұрын
I used the existing ones because I have the lower crash bar from Suzuki. The spacers should be used on both sides.
@vincenzoscarpello2476
2 жыл бұрын
Another clarification, please: to be able to move the suzuki crashbar supplied, in addition to the two upper nuts, have you also loosened the central pin, or does it not touch?
@kers2008
2 жыл бұрын
no I didn't touch that. All that is replaced, loosened or tightened are shown in the video
@vincenzoscarpello2476
2 жыл бұрын
@@kers2008 thank you!
@dirkstrunk8587
2 жыл бұрын
Hi, I would like to mount the crash bars as well. However, one thing is not clear to me when mounting. Do you loosen both front screws of the engine mount at the same time? (rigth and left side) In the instructions from Heed is warned against this.
@kers2008
2 жыл бұрын
I can’t remember but I’m pretty sure I did the left side first. Just follow the instructions from Heed then you should be safe. Mine came without the instructions, so I emailed them and got it later
@dirkstrunk8587
2 жыл бұрын
@@kers2008 Thanks for the quick reply and your support
@christianxzowner2958
2 жыл бұрын
I bought my bike with the lower acc bar on it it don't know who is the brand of origine since im from Canada in the Atlantiques
@vincenzoscarpello2476
2 жыл бұрын
Have you replaced the long screw with an even longer one?
@kers2008
2 жыл бұрын
It’s replaced with the one from Heed that came with the crash bars. But I used the original spacers
@vincenzoscarpello2476
2 жыл бұрын
@@kers2008 Thank you, but I'd like to know: is the Heed screw longer than the original one?
@kers2008
2 жыл бұрын
@@vincenzoscarpello2476 yes it is
@vincenzoscarpello2476
2 жыл бұрын
@@kers2008 thanks a lot!
@amirulhilmi1976
2 жыл бұрын
Can anyone share the link to buy this
@kers2008
2 жыл бұрын
You can buy it here: heedshop.eu/en_US/p/Crash-bars-for-Suzuki-V-Strom-1050/593
Пікірлер: 32