Thank You sooo muchhhh. Only video that worked for me!!!
@EDISON_SCIENCE_CORNER
10 күн бұрын
💚💚
@premiumitservice755
8 ай бұрын
this is how i plan to call my debtors this year , i'll put it on loop
@EDISON_SCIENCE_CORNER
8 ай бұрын
Yeah
@luisgomez5837
8 ай бұрын
Excelente video pero tengo una duda. ¿El RX y TX se pueden conectar directo a los pines D0 y D1 del Arduino Uno?
@EDISON_SCIENCE_CORNER
8 ай бұрын
Better to ask in English.?
@yashpurohit7043
Ай бұрын
Can we do the same thing in vehicles for children safety and gives notification in the parents mobile phone with a audio message??
@EDISON_SCIENCE_CORNER
Ай бұрын
Yes possible
@yashpurohit7043
Ай бұрын
@@EDISON_SCIENCE_CORNER how we can do this pls help me
@yashpurohit7043
Ай бұрын
It's a very imp
@antonito47
10 күн бұрын
Hey, I did exactly everything you did. But it didn´t work. It shows me the at and ok. but when i press the switch it doesnt work. I used a new sim card from KOLBI ICE costa rica. Which SIM am I supposed to use. What am I supposed to do to make it work? Please help!!
@antonito47
10 күн бұрын
Is it neccesary to install the library?
@EDISON_SCIENCE_CORNER
10 күн бұрын
No need to install any library
@EDISON_SCIENCE_CORNER
10 күн бұрын
Please check whether your sim card supports 2G NETWORK
@antonito47
10 күн бұрын
@@EDISON_SCIENCE_CORNER Yeah it supports 2G network
@antonito47
9 күн бұрын
Hi, If I need to use a 5V extra supply where should I connect the 5v to the VIN pin or the 5v pin of the arduino?
@EDISON_SCIENCE_CORNER
7 күн бұрын
Hii
@cyberbeast1789
8 ай бұрын
Good day sir, i just followed your instrustion and the code but i only got AT response from Serial Monitor. What should I do? what does it mean?
@EDISON_SCIENCE_CORNER
8 ай бұрын
Connection problem. You have to check the rx, tx pins
@akashpatil9983
6 ай бұрын
Did you make it work?
@sathyanarayan9079
9 ай бұрын
can i connect a vi or airtel which can support 2g nework? or Some SIM cards and mobile carriers automatically switch between 4G and 2G networks based on the network availability and signal strength. However, the switching capability is often controlled by the mobile carrier, and the module should be able to handle the switch seamlessly
@EDISON_SCIENCE_CORNER
9 ай бұрын
You can use any sim which supports 2g
@Mayank_Chaudhary22
4 ай бұрын
Does Vcc and Gnd of GSMmodule and Vcc and Gnd of JP2 connector are different ??? Please reply fast it will be very helpful for me ...
@EDISON_SCIENCE_CORNER
4 ай бұрын
Yes yes Both are different . You have to connect both to vcc and ground
@rajkumarr157
7 ай бұрын
I have a doubt , I have been planned to built a project that have a sensor and output connected to blynk cloud Also i want to add this call features to that arduino . I have a arduino code for that sensor and the code, you used in this video. How to upload both the codes in the arduino .??
@EDISON_SCIENCE_CORNER
7 ай бұрын
Merge both codes and upload 🤟
@mannycarrion7862
Ай бұрын
i don't mean this in a bad way but, i really like this guy as a teacher bkuz I usually don't understand freaking Hindus but this guy I understand him he talks very well doesn't have that mess up acent were you don't understand bkuz they also talk so fast but this guy his good I like him
@EDISON_SCIENCE_CORNER
Ай бұрын
All indians are not Hindus brother.
@mannycarrion7862
Ай бұрын
Like i said i don't or did not mean it in a bad way all i was saying is that you don't have those fuk up acents that nobody understands, but you don't and speak very clearly and sound like a very good teacher and very intelligent 😁🤓🤓🧠so it wasn't for or trying to insult you ok
@EDISON_SCIENCE_CORNER
Ай бұрын
Me also said it was a bad way. No worries . Thanks. 🤩
@Kevin-go5sg
20 күн бұрын
am just a beginner , so right its taking power from the computer , after uploading the code an adapter must be used to give the supply am i right ?
@EDISON_SCIENCE_CORNER
20 күн бұрын
Thats fine. You can power it with any usb. But make sure it has a rating of 1A minimum
@Siblingvlogs39
4 ай бұрын
Please can You make same thing with Sim800l?? It will help a lot
@EDISON_SCIENCE_CORNER
4 ай бұрын
I tried but it failed.
@BabangidaYohanna-s8w
Жыл бұрын
I will love to try his code.. Thanks
@EDISON_SCIENCE_CORNER
Жыл бұрын
Go for it
@VijayVighnesh
11 ай бұрын
Thank you sir it is working.
@EDISON_SCIENCE_CORNER
11 ай бұрын
🤩
@studshelper9901
11 ай бұрын
you used 4g sim or 2g sim
@gentleman7060
9 ай бұрын
Its sim 900A mini module right? Can i use it with my arduino uno + gps module to send data to my firebase node?
@EDISON_SCIENCE_CORNER
9 ай бұрын
Yes possible
@gentleman7060
9 ай бұрын
@@EDISON_SCIENCE_CORNER is there any video or resource to do that?
@MrJumbledUp
9 ай бұрын
thank you so much
@EDISON_SCIENCE_CORNER
9 ай бұрын
❣️
@kfaiz92
3 ай бұрын
The module can call phone but can we call the module? Also does it ring when we call?
@EDISON_SCIENCE_CORNER
3 ай бұрын
Yes possible
@RanjithGaniga-o4c
2 ай бұрын
in serial monitor it is showing ok but call is not going pls reply fast it is help full to me
@EDISON_SCIENCE_CORNER
2 ай бұрын
Which sim
@concocktenation
2 ай бұрын
do I need load balance to work the call or send sms of the sim inserted in thr sim900a?
@EDISON_SCIENCE_CORNER
2 ай бұрын
Yes .
@ammontv8716
Жыл бұрын
What will happen if you answer the call? Are you able to talk through the cellphone onto the arduino circuit?
@EDISON_SCIENCE_CORNER
Жыл бұрын
Yes we can
@ammontv8716
Жыл бұрын
You sure? Even no microphone and audio components?
@CM_AyushDhewale
8 ай бұрын
Can we use 4g sim of vi, airtel, bsnl directly in that module, is there's services support or not.
@EDISON_SCIENCE_CORNER
8 ай бұрын
Yes you can use those sims
@deepanjalimishraa
5 ай бұрын
@@EDISON_SCIENCE_CORNERthen why did you said to use a 2g sim 2g or 4g or anything?
@EDISON_SCIENCE_CORNER
5 ай бұрын
I said to use 2g sim only. The 4g sim of vi, bsnl will support 2g also. But jio will not support
@thoulkappiyanm5148
7 ай бұрын
bro we have to use the original sim of the number or a duplicate one plss reply
@EDISON_SCIENCE_CORNER
7 ай бұрын
Both will work
@thoulkappiyanm5148
7 ай бұрын
@@EDISON_SCIENCE_CORNER TQ bro
@mauro11553
10 ай бұрын
instead of the button to make the call suffer, can it be done that the call starts every time the Arduino is powered by 12 V?
@EDISON_SCIENCE_CORNER
10 ай бұрын
Possible
@mauro11553
10 ай бұрын
@@EDISON_SCIENCE_CORNER take me your email please, i write you?
@antonito47
10 күн бұрын
Hi, my sim card is combatible to 5G 4G 3G 2G, does it work? Could it be the voltage or the curent of my arduino? What can I do, it still doesn't work. I have to send my proyect next week 😭
@EDISON_SCIENCE_CORNER
7 күн бұрын
Please check the pinned video
@payotrhyskelseyzabdielj.1357
Ай бұрын
is the MODULE have mic to talk with the phone?
@EDISON_SCIENCE_CORNER
Ай бұрын
Yes but not tested yet
@farookhossen702
4 ай бұрын
now i have a 4G sim card , now can i used this card cause this sim card also 2G , 3G. they work automatically or not work . please tell me what do i .
@EDISON_SCIENCE_CORNER
4 ай бұрын
If your sim supports 2G then you can use this module.
@pawangour9627
8 ай бұрын
sir is that suit to 4g or 5g sim which module is use for 4g or 5g sim
@EDISON_SCIENCE_CORNER
8 ай бұрын
2g SIM only
@drelectronics13
Жыл бұрын
I never bought such module cause 2 g support is not permanent,we need 4 g support ,if u have any 4 g module with small price tag it will b good
@EDISON_SCIENCE_CORNER
Жыл бұрын
No provider is going to end 2g service soon
@Parixit_Chaudhari
9 ай бұрын
Sir , which 2g sim you are using ?
@EDISON_SCIENCE_CORNER
9 ай бұрын
BSNL and VI
@eswarelectronics4205
Жыл бұрын
Bsnl connecting India mine also bsnl 😊
@EDISON_SCIENCE_CORNER
Жыл бұрын
Bsnl
@cdtf8534
10 ай бұрын
the SIM900A needs far more current then the Arduino can deliver, thats why some SMS sending dont work. The module can consume peaks of 2A during sending Use a separate power supply or better a 3.7V Li-ion cell !!!!
@EDISON_SCIENCE_CORNER
10 ай бұрын
That's correct but it got worked for me
@fablapp
Ай бұрын
the wiring does not seem to work for me. The SIM900 seems to work if it is directly connected to the arduino 5V. althought I red thatt his should be avoided... but it works. however this means that theres no power for other sensors
@EDISON_SCIENCE_CORNER
Ай бұрын
?
@fablapp
Ай бұрын
@@EDISON_SCIENCE_CORNER the trick you made withthe double connection seems not to work for me.... I tried on the breadboard and cannot get enough current.... also if I connect directly to the 5 volt I am left with nothing for the other sensor I want to hook to the arduino... I need an external power supply...
@engineerlawalhamzatademola4267
Жыл бұрын
Please I need tutorial on "how to dial ussd using sim900 and Arduino" or simply show me the documentation? 🙏🙏🙏🙏
@EDISON_SCIENCE_CORNER
Жыл бұрын
Check the videos
@ronaldmarkundag346
Ай бұрын
Please help do 2G,3G and 4G support this module?
@EDISON_SCIENCE_CORNER
Ай бұрын
It supports 2G only
@VijayKumar-xh2kz
8 ай бұрын
I was using this gsm module SIM 900A for Earth quake detector alerting process but I didn't receive the sms or call after I dumped the code
@EDISON_SCIENCE_CORNER
8 ай бұрын
Please watch the video carefully , check whether your sim supports 2g, check connections
@dharmeshyadav5741
21 күн бұрын
Can you tell me about how to do sms sending ?
@EDISON_SCIENCE_CORNER
20 күн бұрын
You need to use different command
@dharmeshyadav5741
14 күн бұрын
@@EDISON_SCIENCE_CORNERplease tell me how to do that?
@ICYFLAMES6963
10 ай бұрын
hey you said if it shows AT continuosly we have to check our connections.... I checked it but i still dont see ok plz help i have a project to make
@EDISON_SCIENCE_CORNER
10 ай бұрын
Check SIM and connections
@ICYFLAMES6963
10 ай бұрын
sir i checked it but the sim is alright @@EDISON_SCIENCE_CORNER
@akashpatil9983
6 ай бұрын
Hey did you make it work?
@ICYFLAMES6963
5 ай бұрын
Yes it worked at the end
@alfredb.a.
4 ай бұрын
i have the same problem, how did you make it work?
@xinxin9461
26 күн бұрын
my gsm module is kind of blinking faster than yours is it normal??
@EDISON_SCIENCE_CORNER
26 күн бұрын
Use my whatsapp and send
@xinxin9461
26 күн бұрын
@@EDISON_SCIENCE_CORNERi think it has to do with the 9v 2amp stuff
@chifonlesley3011
Жыл бұрын
Please how can u check if gsm is connected to Arduino uno using hardware serial port
@EDISON_SCIENCE_CORNER
Жыл бұрын
I explained it in the video have you watched the video.?
@bharadhanpadmam2526
Ай бұрын
How much power supply we should give to this please replay me
@EDISON_SCIENCE_CORNER
Ай бұрын
5w
@EDISON_SCIENCE_CORNER
Ай бұрын
5v 1a
@stephan_coker
7 ай бұрын
Can you provide the coding to send SMS with the use of a push botton?
@EDISON_SCIENCE_CORNER
7 ай бұрын
Yes will do
@dharmeshyadav5741
21 күн бұрын
@@EDISON_SCIENCE_CORNERplease give me
@vishalgfx131
11 ай бұрын
Bread bord is not Compalsary Only if we use switch
@EDISON_SCIENCE_CORNER
11 ай бұрын
Yeah
@zoroark9733
10 ай бұрын
is there any way i can make the sim900a work in the US?
@EDISON_SCIENCE_CORNER
10 ай бұрын
You can use
@francisjosesucgang4499
4 ай бұрын
Is it possible for 4g?
@EDISON_SCIENCE_CORNER
4 ай бұрын
No
@anxious_cxx
Ай бұрын
Does I use sim 800 l module
@EDISON_SCIENCE_CORNER
Ай бұрын
You can
@melongaming2056
Жыл бұрын
Can we do the module without button?
@EDISON_SCIENCE_CORNER
Жыл бұрын
Means
@DarPlayz..2097
Жыл бұрын
HI, bro i connected all properly and done code also but i am not recieving call and in the GSM board nwt is blinking continusly help me pls psl psl
@EDISON_SCIENCE_CORNER
Жыл бұрын
Will your sim support 2g
@HansHilotin
10 ай бұрын
Why it's nkt working? It's not calling me😭😭😭
@EDISON_SCIENCE_CORNER
10 ай бұрын
Check sim
@HansHilotin
10 ай бұрын
@@EDISON_SCIENCE_CORNER yes it has load, when we try to run it it says calling but we are not recieving a call
@EDISON_SCIENCE_CORNER
10 ай бұрын
Which sim , does it support 2g
@HansHilotin
10 ай бұрын
@@EDISON_SCIENCE_CORNER maybe? Because our sim is a 5g
@cricket-edit.
3 ай бұрын
Change the number
@do55_afg12
5 ай бұрын
The AT command not showing for me could you help me
@EDISON_SCIENCE_CORNER
5 ай бұрын
Have you selected the correct baud rate.?
@samadhangaikwad587
2 ай бұрын
Sir muze aise he chayae par phone call ke jaghe par message jana chai a 3 parson ko
@EDISON_SCIENCE_CORNER
2 ай бұрын
English please
@mc_nudo
4 ай бұрын
with this module you can call cellphones, you can also do it with the smaller ones? like sim800L?
@EDISON_SCIENCE_CORNER
4 ай бұрын
Yes possible
@zuhebsadiqha
Жыл бұрын
I have bsnl sim still it is not sending sms ? Is it having settings ?
@EDISON_SCIENCE_CORNER
Жыл бұрын
Which code you used
@muhdakmal150
5 ай бұрын
what library that i need to download?
@EDISON_SCIENCE_CORNER
5 ай бұрын
No Library needed
@kartikvisvanathan3129
Жыл бұрын
Sir is 4G sim valid for gsm module
@EDISON_SCIENCE_CORNER
Жыл бұрын
No this is a 2g module
@benfoxplayz8661
11 ай бұрын
@@EDISON_SCIENCE_CORNERBut the sim you used is 4G bruh
@EDISON_SCIENCE_CORNER
11 ай бұрын
I said no
@neilcristopherocampo4660
5 ай бұрын
Why our project isnt working?
@EDISON_SCIENCE_CORNER
5 ай бұрын
Check description and send message to my WhatsApp
@neilcristopherocampo4660
5 ай бұрын
We got no call?
@EDISON_SCIENCE_CORNER
5 ай бұрын
Which sim and 4G
@eswarelectronics4205
Жыл бұрын
Please add a speaker and mic option
@EDISON_SCIENCE_CORNER
Жыл бұрын
Yes
@Gentlestudy
10 ай бұрын
How I get 2g sim
@EDISON_SCIENCE_CORNER
10 ай бұрын
Vi, Airtel, BSNL sims support 2g
@Gentlestudy
10 ай бұрын
@@EDISON_SCIENCE_CORNER 4g card ? Of these company
@gonemad940
11 ай бұрын
The light is in module is on but it not calling in serial port the error is showing pls help i need your help
@EDISON_SCIENCE_CORNER
11 ай бұрын
Two LEDs there . One is a power LED and another is a status LED. Status LED should blink in every 3 seconds.
@gonemad940
11 ай бұрын
Ya the status led blinked every3 second
@gonemad940
11 ай бұрын
But it didn't make call
@gonemad940
11 ай бұрын
Output is not coming in serials port
@EDISON_SCIENCE_CORNER
11 ай бұрын
Change the tx rx pins
@thoulkappiyanm5148
3 ай бұрын
Bro this error is occurring what can I do bro avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xa3 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xa3
@EDISON_SCIENCE_CORNER
3 ай бұрын
Which arduino board
@thoulkappiyanm5148
3 ай бұрын
@@EDISON_SCIENCE_CORNER rectified bro thank you for the reply
@SantoshSharma-nh2sj
11 күн бұрын
Bro make sure in you arguing board d1 and d0 pin I'd disconnected
@venkateswararasupalli7719
Жыл бұрын
bro can we use 4G sim for this experiment
@EDISON_SCIENCE_CORNER
Жыл бұрын
You can buy it should support 2g
@InDynamics
Жыл бұрын
Bro please tell a 4g module with low price
@InDynamics
Жыл бұрын
By when can I expect your reply?
@EDISON_SCIENCE_CORNER
Жыл бұрын
Not available
@venkateswararasupalli7719
Жыл бұрын
If we use 4g sim what will happen
@EDISON_SCIENCE_CORNER
Жыл бұрын
This is a 2g module
@Tx_6969
Жыл бұрын
Sir please help me.. I can't find the softwareserial.h Library 😢
@EDISON_SCIENCE_CORNER
Жыл бұрын
Search in Google
@Tx_6969
Жыл бұрын
@@EDISON_SCIENCE_CORNER Thanks I found it😊. Really nice video bro
@Tx_6969
Жыл бұрын
Sir this code is not working 😢
@EDISON_SCIENCE_CORNER
Жыл бұрын
What error.?
@invisor7986
9 ай бұрын
Why my gsm become🥵 after i connect to usb com
@invisor7986
9 ай бұрын
Plss help
@invisor7986
9 ай бұрын
And it's doesn't blinking at all
@EDISON_SCIENCE_CORNER
9 ай бұрын
May be damaged GSM
@venkateswararasupalli7719
Жыл бұрын
please provide code in comment box we are unable to download
@EDISON_SCIENCE_CORNER
Жыл бұрын
Chech the video description
@anilkumar-cd1pp
9 ай бұрын
Sim900 support 4g sim
@EDISON_SCIENCE_CORNER
9 ай бұрын
No
@samoletbumazni951
Жыл бұрын
🥰🫶
@ICYFLAMES6963
10 ай бұрын
plz help
@EDISON_SCIENCE_CORNER
10 ай бұрын
😊
@ashikartcell6528
Ай бұрын
I tried but failed.I Can't get any message or phone call.I am from Bangladesh
@EDISON_SCIENCE_CORNER
Ай бұрын
This one is only for calls. Please check the connections and show me whats in the serial port.
@studshelper9901
11 ай бұрын
will this support 4g sim
@EDISON_SCIENCE_CORNER
11 ай бұрын
No
@studshelper9901
11 ай бұрын
@@EDISON_SCIENCE_CORNER
@warrenjoedeguzmam5505
Жыл бұрын
what the problem if ERROR keep showing in the serial monitor?
Пікірлер: 191