A good idea is to use a genuine JIS Phillips screwdriver. JIS stands for Japanese Industrial Standard and it fits the screws a lot better, therefore lowering the risk of stripping the phillips head screws.
@coleexotics
Жыл бұрын
Thank you. You helped out a lot
@user-lk6cf1sx9u
9 жыл бұрын
The southern accent makes it that much more official.
@Roger_Ramjet
"Carburayter"
@nicholasventura4107
3 жыл бұрын
Honda ruskus 49cc only have 5 miles
@chewyyang4606
2 жыл бұрын
Do I need to adjust the air/fuel screw after putting these on?
@ericparisien3051
8 жыл бұрын
Thanks for this video, on a stock everything, what would be my advantage to change the slow jet from a 35 to a 38? And should I also increase the main 75 and to what, and what will it improve?
@-Just_Justin-
4 жыл бұрын
What jet sizes would you use for 7000feet in elevation for the pilot and main jet? Loved the in depth how to video
@abnerbjorn1106
8 жыл бұрын
Great video, Can you tell me if there is a passage below the main jet that might get clogged. I pulled the carb on my 07 ruckus that had sat for a year. Cleaned both jets and reassembled. It idles great, but won't go above 15 mph. When I give it gas it kicks down to idle. I've re-set the diaphragm 3 times thinking that was the problem, but no go. Thank you in advance!
@nicholasventura4107
3 жыл бұрын
I have jet carb. Notice start den it Stalled out can you help me with this problem
@markcoppola2461
3 жыл бұрын
Question: I went up to 38/80 with an intake and exhaust and gained great mid range but lost a ton of top end and it slightly Boggs ? What am I doing wrong
@jug3r295
6 жыл бұрын
If I put a yosh and a air bix eliminator, i need to jet it but just the main jet or te slow jet also? I dont understand what is the utility of the slow jet. Sorry for my bad english, im french
@Wick3dn0mad
8 жыл бұрын
Any chance Yall will have more in stock?
@morphesus820001
8 жыл бұрын
What size pilot jet and main jet when you want to run methanol? Jetting for alcohol (methanol specifically)
@TheDevilsDisco
8 жыл бұрын
Hey, I'm a dolt and couldn't easily get the pilot jet off, leaving it a bit damaged. What would be the best way to proceed to remove it?
@DogBoxDeluxe
5 жыл бұрын
would the 38 Pilot and 78 Main jet work with a stock set up? Or should you just stay 35 Pilot and 75 Main?
@becraveiro1
4 жыл бұрын
Hey, thank you for the video. Very helpful! Quick question, I am installing a new exhaust and i will most likely need to re-jet it, do i have to change the slow and the main or just the main? Also, how to I know what size I have installed? I cant seem to find it on the part itself. Thank you!
@BozidarPavlicic
8 жыл бұрын
Koje su velicine dizne nnapisi neznamo svi engleski?What are the size of nozzles nnapisi not know all the English?
@EluderRacing
6 жыл бұрын
hey great video! I was wondering what you recommend for a stock rockus. I always felt they ran a bit lean for maximum economy based on plug color. have you ever tried jetting a stock rockus and noticed a change after bigger jets where installed I not care about fuel economy. I have been thinking about adding a aftermarket exhaust I want to see if I can find something to add a little deep tone to the sound of the bike with almost stock db levels so I guess my question is a 2 parter lol.
@rejexcollects2088
4 жыл бұрын
What size main jet do you reccomend on just an intake mod?
Пікірлер: 60