Hey man its me, the one who you bought the truck from, man those heads were heavy , and I'm still surprised we got that block into the truck bed haha, im really glad its finally getting the love it deserves. Always wanted to do a swap on it. I hope it all goes well with it man I really miss my truck and seeing it get some life breathed back into it just makes me wish I didn't have to sell that much morw
@latingeek867
2 жыл бұрын
Like everyone else says, this video really helps a ton, I'll be attempting to LS swap a 93 Blazer (2 door tahoe). I'll also be using the original trans since it's a 4WD, thanks again for the informative vid.
@ernestorodriguez8228
2 жыл бұрын
Nice a good in depth video to learn from point a to point b
@michaelfisher8824
9 ай бұрын
where did you send your PCM to get flashed? I bought a running LQ4 4L65 with complete harness, PCM, trans controller, pedal from running 2007 Silverado 2500. New power plant for my '87 Chevy Scottsdale
@bradmurphy9670
2 жыл бұрын
Do you by chance have a list of parts you used for the swap. Like the oil pressure sensor adapter and the temp adapter. Also the fuel line parts fuel pump and stuff like that. Going to be doing my swap on my 86 K20 soon. Would love to be able to swap as easy and quick as you did.
@bradleycrenshaw6778
2 жыл бұрын
Man this channel is soooooooooooooooooooo real world garage stuff. What a refreshing change. No loud stupid music, no filthy language.
@cwmotorsports4497
2 жыл бұрын
I thought this video was going to be such a long video but It went by so fast and has so much great information. I've done mutiple ls swaps and there are a lot of ways to do them but this is really great. Very cost effective and straight to the point without buying all the aftermarket parts that most people think they need. Great JOB.....
@piratejetgarage
2 жыл бұрын
Thanks! That is exactly what we were going for. Thanks for watching and taking the time for the kind words.
@kw2519
2 жыл бұрын
Ya, this was super helpful. Been eyeballing 80s Chevy pickups lately…
@codyrob94
11 ай бұрын
Agreed. Transmission just crapped out in my rusted 1500hd. Also happen to have an 84 k20 in the shop that needs a motor. This was way better than reading forums and getting 25 different answers for one thing. Thanks!
@cswildcat09
2 жыл бұрын
Glad I found this video in my recommended feed today, actually answered a lot of unknowns about my own 85 K10 LS swap and how to do power steering lines! Thanks for the video man
@piratejetgarage
2 жыл бұрын
Thanks for watching!
@TC_AZ
2 жыл бұрын
If you're not doing hydro-boost remove the fitting from the back of the LS power steering pump and use the original (k10) power steering pressure hose to the steering box. I just picked one up at AutoZone with a lifetime warranty, that was nearly 10 years ago haven't changed anything
@ClumsyCars
2 жыл бұрын
@@TC_AZ you can also use a 99 Silverado 5.3 pressure line, same threads as the later model squares
@garrettharris1255
2 жыл бұрын
I have a 68 gmc short bed with 3.73 rear end and a 350 turbo trans I’m putting a 6.0 ls in. And it’s been such a struggle finding any information on a full guide. But you did a awesome job! I’m a poor ole boy so you definitely showed me how to do it on a budget!!! Thanks again my friend!
@piratejetgarage
2 жыл бұрын
Thanks for the kind words. Good luck with your project, it sounds really cool.
@gerardolopez5875
2 жыл бұрын
Go with the 4L60E,,
@rustyjunkgarage1418
2 жыл бұрын
This a great video that takes the myths and BS out of an LS swap. People look at it costing big bucks when really thats not always the case. I picked up some good tips here! Glad to know the power steering lines are so easy to deal with. I have an 84 K20 that I planning on swapping.
@codyrob94
11 ай бұрын
I’ve got an 84 k20 also. Tranny in my 1500hd just crapped out so hopefully I can make something happen.
@Figure-it-out
Жыл бұрын
Definitely just gave me some more confidence. I’m looking at a C10 with the 6.2 diesel and was worried LS swapping would be a pain. After watching this I have no doubt I could get it done in a couple weekends. Thanks
@LordNotlek
3 ай бұрын
Man the 6.2 is goat
@2muchspl
2 жыл бұрын
Im starting my LS swap soon in my Nova. Ive done tons of reading,knew what to take from donor truck,what not to cut,etc....when I tell you this is the most informative step 1 to final video on KZitem please believe me!!!! I effin added you to my personal KZitem account I watch in the living room, idc if you never post another video: this was well done!!
@piratejetgarage
2 жыл бұрын
Wow, thank you for that. Good luck with your swap!
@jonesdamisfit
2 жыл бұрын
Would you happen to have links or part numbers to all of the parts used adapters, fittings, hoses and etc
@ghostghost5042
2 жыл бұрын
I appreciate this video that you put up I have a '97 dually diesel and I'm swapping it over to LS and the video was very helpful with the project I have ahead of me thanks
@PhilsF
2 жыл бұрын
Great video... just goes to show that an LS swap can be done on a budget.
@piratejetgarage
2 жыл бұрын
Thanks for watching!
@jesseison-bowman3964
2 жыл бұрын
Great work! It's obvious that you really know Chevy's and not your first LS swap. I have a black 84 K5 Jimmy with the exact same front end as your dually. In all honesty I am very comfortable with all of the steps in your video except wiring up that fuse box. Wondering if something like a Painless or other aftermarket harness and fuse box might be more plug and play? All of the different options for power sources, etc.is very intimidating but I freely admit that electrical is my weakness by far. Thank you!
@simple_man_jkb
2 жыл бұрын
This is the most informative ls swap video I have see yet. I’m in the process of swapping a 02 z71 engine and trans into a 95 z71
@piratejetgarage
2 жыл бұрын
Thanks, good luck with your swap!
@stevepope5484
2 жыл бұрын
I'm glad I found this too. Bought an 03 yukon last week/bought 67 Malibu last January? I'd do exactly what you've done with the wiring.Hope to. Not sure about using the auto n cutting the tunnel/or going stick.old 3 or 4 spd. Having cruze would be cool/but probably far fetched. Wish the a/c could be used off the 03 too. Hec/the stereo in this rolled over worn out yukon is even Really Fine sounding! HA.
@Mr.Thermistor7228
Жыл бұрын
can we take a moment to pause and ask just WTF is actuallyy going on in that opening scene??? i cant believe myy eyes....
@piratejetgarage
Жыл бұрын
Seriously! How are you only like the second person that has even mentioned it…. I thought there would be 500 comments about it.
@ice4278
2 жыл бұрын
I have a 66 C10 that I wanted to put an LS in but most video Don't Kill enough information I want to thank you for really detailing now I might go ahead on and do it on the OBD connector you didn't say anything about position 1 and 3 you don't use them .
@SchneiderClassics
2 жыл бұрын
now you never see that, running motor going into a truck XD
@piratejetgarage
2 жыл бұрын
I’m shocked that hardly anyone has even mentioned it… lol
@the_truck_farmer
2 жыл бұрын
I like your approach to using as much From the donor truck as possible. Same way I’d do it! Call me old fashion but hp/ foot pounds aside I like the low rpm tractor torque from a SBC/bbc for a HD pickup much better than the 2500rpm peak torque of an LS. The LS is the ideal sports car or truck engine with its high rpm power band. Definitely to each their own though. Love your exhaust sound!
@davidorozcoish
2 жыл бұрын
Thank you guys, great video. You're gonna save me a ton of hours on the harness.
@joelaughlin2815
2 жыл бұрын
Would a set of headers eleminate most of the welding
@piratejetgarage
2 жыл бұрын
Absolutely, They make so many bolt in parts for these trucks. We were trying to keep this build inexpensive.
@V8Power5300
2 жыл бұрын
You can actually use PCM hammer and tunerpro to flash the ecu yourself. You just need a cheap supported obd adapter
@terrancesells3250
2 жыл бұрын
Do you have a link for it?
@stevepope5484
2 жыл бұрын
Speak on.
@815LSxSwaps
2 жыл бұрын
Nice! Got to love an ls swapped square body!
@piratejetgarage
2 жыл бұрын
Thanks!
@rogerm881
Жыл бұрын
This video made me get my swap done good shit 🔥
@failranch9542
2 жыл бұрын
If the dome light ever fails and it’s dark out, just get the check engine light to illuminate. Problem solved. Never seen such a bright CEL.
@tblocksidge
2 ай бұрын
Do you by chance have a list of parts you used for the swap. Like the oil pressure sensor adapter and the temp adapter. Also the fuel line parts fuel pump and stuff like that. Going to be doing my swap on my 79 K20 soon. My donor truck is a 2011 Silverado with a 6.0L. do you have any recommendations for this year of motor?
@RedWhiteAndBlueVideo
2 жыл бұрын
Great and Informative Video! Only up 8 days and 22k views. Seems pretty amazing and should net you many more subscribers. At first I didn’t know if I wanted to watch an hour video by someone I never watched before. Glad I did. Definitely the best LS swap video so far. I would have had to watch multiple videos by other youtubers and still not get all the info you contained in one hour. Will the harness get any more work done to it?
@piratejetgarage
2 жыл бұрын
Thanks for watching and the kind words. We appreciate both. Thats it for the harness.
@Calebburdick
3 ай бұрын
I’m swapping a 99 LQ4 6.0LS into a 76 C20, picking up a 87 tank, and 87 fuel sending unit… what did you end up doing with your vent on the fuel sending unit?
@Calebburdick
3 ай бұрын
I’m swapping a 99 LQ4 6.0LS into a 76 C20, picking up a 87 tank, and 87 fuel sending unit… what did you end up doing with your vent on the fuel sending unit?
@VegasRT500
2 жыл бұрын
That truck deserves a big block 496 engine that pumps out 600hp and 650TQ. You cant beat the big block for towing power.
@junkyarddawgfixit8970
2 жыл бұрын
Nice job and great video, just a note about the GM engine mounts, the rubber mount that bolts to the frame is the "clamshell mount" and the part that bolts to the engine is called the "elephant ear" bracket.....keep rolling
@WayneEarls
2 жыл бұрын
An time I can get rid of a boss I do.
@DieselJunkie12v
Жыл бұрын
So i have a 5.3 from a 2001 suburban that has cats and egr. Can i just shut off vats and trans controls (using a 700r4) or do i need to do everything? Vats, rear 02s, egr stuff, trans controls, and disable all dtc checks so it doesn’t throw codes?
@ghogman
6 ай бұрын
Do you guys have a list of everything you bought to do this swap? The pump, wires, tank, manifolds, gaskets ect?
@EASTSIDE-313
2 жыл бұрын
Very nice detailed to the point video. You do nice work, keep it up, nice to see . Got my sub.
@blakeniemann2344
2 жыл бұрын
Great video! This is what gives me the confidence to do an Ls swap, keep up the great work!! Thank you
@mrclean146
2 жыл бұрын
Love it. Great content. But that red...That's hot. Lol
@sonnydash4987
8 ай бұрын
Ive only subscribed to 7 channels. This is #8. Keeping it real! Great video good content.
@jhartwells
8 ай бұрын
When you trim down a bolt you run the die on. At first run it all the way to the head, trimmed on the bolt and then run the die back off. It will clean up the threads for you. Also, if you round the tip of the bolt just slightly before running the die off it makes it even better.
@greddmyles3677
Жыл бұрын
Could've just bought a 4l80 flex plate and bolt right on, no need for spacer or hole waddle or nothing
@maxjones9139
2 жыл бұрын
very well done! Thank you!
@almonjacob3496
8 ай бұрын
Sorry, I can't watch someone who wears rubber gloves while wrenching!
@roytrevino9109
7 ай бұрын
Great video, thanks,a lot of good information ,so I'm not so intimidated by the swap !
@joncabana1
8 ай бұрын
you can use a flex plate of like a 4.8 express van the flex plates are beefier and adaptor is built in and bolt holes should line right up
@oldschool337
2 жыл бұрын
Did you get the computer flashed
@giovanniceballos-y7e
28 күн бұрын
Bro, that red wire that needs to be Constantly hot. Put it close to the radiator that way, it stays hot with the heatness of the radiator
@DIYG35DALE
6 ай бұрын
26:45 I see this is an older video, but do you guys happen to have the part number you used for the tank, sender and pump?
@justinnonyabuisiness7453
8 ай бұрын
Hey I know this is an older video but I was wondering if you had a parts list of everything needed to do the ls swap
@timbarnett3898
2 жыл бұрын
My friend, Craig, an I did engine change. Craig had 350 in El Camino & 454 in suburban, so we changed motors too make El Camino a burn out car! That was when gas was cheaper!
@piratejetgarage
2 жыл бұрын
Sounds like a cool project, thanks for watching.
@78sergiobarias
5 ай бұрын
hello, what sender and fuel pump was used thanks does anyone have part numbers?
@dawsonhoyt505
Жыл бұрын
Do you got a list of what I’d need to an ls swap on a 1986 k20 standard
@kenkem396
9 ай бұрын
straight forward and right to the point. and no bullshit love it!!
@Cotylove2007
2 жыл бұрын
Part number for the dorman fuel line kit?
@xXdarkcloud47Xx
10 ай бұрын
Hello I was wondering if you what would I need is swap a 72 nova
@jermainebowers9650
4 ай бұрын
Who did u send your pcm off to I’m trying to get my vats off
@grantdubiel4843
2 жыл бұрын
Now if only I had a garage to do mine in lol, got a 92 k2500 going to 6.0 swap
@piratejetgarage
2 жыл бұрын
Sounds cool, good luck!
@jesuschrist2886
2 жыл бұрын
I'm not a GM person at all, but I have to say this was one hell of a swap. gives me more ambition to get my truck fixed!
@piratejetgarage
2 жыл бұрын
Thank you for watching! Good luck with your project.
@youbreakityoufixit9594
2 жыл бұрын
Excellent video! I learned a lot
@piratejetgarage
2 жыл бұрын
Thanks so much for watching.
@isaacgriffenberg6347
2 жыл бұрын
Beautiful truck! Rubber gloves with power tools could get ugly though. Be safe!
@piratejetgarage
2 жыл бұрын
Thanks for checking it out!
@troyparr7013
2 жыл бұрын
Total break down cost? Extra parts etc
@TheNewkidsrule
8 ай бұрын
Rubber gloves with a grinder & no guard 😂
@workingmansrestorations7071
Жыл бұрын
This is crazy. I cant believe it if i didnt see it
@pakistansolarsystems3648
2 жыл бұрын
Sir I have Toyota Hilux 1985 model and I am sweep engine but I have no engine can you gift for me please.
@piratejetgarage
2 жыл бұрын
Sorry, can’t help you there.
@pakistansolarsystems3648
2 жыл бұрын
Ok
@808chevykev
2 жыл бұрын
I watched this like a movie! Popcorn and all!👍👍👊✌
@piratejetgarage
2 жыл бұрын
Big thanks to you!
@outfitsgarage88
2 жыл бұрын
Great video. I'm looking to do this to my old 85 ford f350. I will be watching again.
@piratejetgarage
2 жыл бұрын
Thank you!
@sps-vf4qq
2 жыл бұрын
booo, get a chevy you bum
@TheBigblue04
6 ай бұрын
Can you tell me about how much fuel line did you need?
@Super1967ford
2 жыл бұрын
Thanks, I will be using this video this summer to do a swap, definitely makes it’s easy with a step by step
@piratejetgarage
2 жыл бұрын
Thanks so much for watching.
@jonpaulison2283
9 ай бұрын
Awesome video thank you so much ...
@honest8bob
2 жыл бұрын
A 2x4 welding table, someones got the big bucks!
@stevepope5484
2 жыл бұрын
I notice that! Haha
@205_bowties
2 жыл бұрын
Best video I have seen for ls swap squarebody thanks
@piratejetgarage
2 жыл бұрын
Thanks so much!
@brucewest616
2 жыл бұрын
Camper special ? could it b the rear axle is moved farther back to the rear for towing and wrecker applications longer wheel base but shorter to the rear wheels from bumper hitch ?
@piratejetgarage
2 жыл бұрын
Camper special was a factory package available on these trucks. I’m no expert for sure but a quick google search makes me think this might be a deluxe camper special. Extra beefy for a big slide in camper.
@oldcroneysgarage9739
2 жыл бұрын
Camper special had upgraded leaf springs, camper tie downs, and the camper special units had the camper special badges, the truck you see in the video has Cheyenne badges instead of the camper special badges for some reason 🤔
@trulyblessedziiz1030
2 жыл бұрын
I like your style 😎 👌
@kindoutdoors6755
Жыл бұрын
Not to sound dumb, but is a 5.3 votec and ls the same thing or something else that would need different parts?
@MrJayo73
Жыл бұрын
It's the same platform vortec (truck) will have iron block in most cases and the ls (car) will have aluminum. Intakes are different but interchangeable
@prestonnielson6120
2 жыл бұрын
I thought this was a great video thanks for doing it !
@piratejetgarage
2 жыл бұрын
Thanks for watching!
@jparker7parker883
11 ай бұрын
What dorman fuel line kit is that
@CavanalK5
2 жыл бұрын
Very impressive. Obviously a guy could take some extra time and clean up and perdy up wiring and so on, and I know that wasn’t the goal of the build you did. This really helps illustrate the how to of it and shows how simple it can really be. I take my hat off to you for making and posting this. I’ve been researching this swap for years on my ‘88 K5. I just need to start gathering parts and dive off into it. Thank you for posting and i’m subscribed, awaiting for great content. take care 🤙🏼
@piratejetgarage
2 жыл бұрын
Thanks for the kind words!
@stevepope5484
2 жыл бұрын
I liked the wiring? Bolt the fuse block neatly/nobody ever see the back. Why push all the pins out? It looks as neat as it did from GM? Perfect
@danmcelroy6584
2 жыл бұрын
That sure made swapping engines look easy. Sure don’t have to rip out all the wiring like I heard. Maybe now I can put my little 08 4.8 with trans and transfer case in a Jeep Cherokee easier. Thanks for sharing! Sweet looking and sounding truck! 👍👍
@piratejetgarage
2 жыл бұрын
That sounds interesting! Good luck with your project. Thanks for watching.
@danmcelroy6584
2 жыл бұрын
@@piratejetgarage it’s more a dream at the moment. But it is what I want. Just a little pep in ponies and lifted and stiffened up so it don’t pop the windshield. I have the 08 engine. It’s in my truck and the frame is going bad..Thank you again.
@CitizenX88
2 жыл бұрын
Bevel any bolts you cut and you won't ever have threading problems .
@stevepope5484
2 жыл бұрын
Washers.?
@CitizenX88
2 жыл бұрын
@@stevepope5484 what about them ? They go on just fine . Beveling your bolts doesn't mess with washers it doesn't mess with the diameter of the bolt or the shoulder . Almost all botls get washers and I bevel all bolts that I cut .
@V8Power5300
Жыл бұрын
This is very similar to how i did my 88 Cadillac Brougham. I pretty much used the same style engine mounts. Stock radiator, 4l60e swapped in and single 3" exhaust. I used PCMHammer and TunerPro to remove VTAS and tune myself. All you need is a 40$ ODB2 dongle. A/C used R4 compressor conversion mounts
@artfordlowery490
2 жыл бұрын
Awesom gmc truck 🚚 VERY GOOD 👍 mechanics job 👏 👌 thanks for sharing your experience and knowledge 👍 with us 🇺🇸
@nickstewart3725
2 жыл бұрын
I got a 94 Chevorlet Suburban K1500 4x4 and I plan on LS or LT swapping the truck...the ol' 350 TBI just don't have the power I want...great video to watch right here and well explained!
@michaelfisher8824
Жыл бұрын
Super helpful! At the very beginning of doing LS swap into my 87 Scottsdale 3/4 ton HD 4x4. Using LQ4 with 4L80e. LMC truck has nice LS swap wire harness.
@fir3gun
2 жыл бұрын
is no one gunna talk about the beginning?? LOL
@piratejetgarage
2 жыл бұрын
lol
@luisbatista1103
2 жыл бұрын
Great video...new sub 👏👏👏👍🇨🇦
@piratejetgarage
2 жыл бұрын
Thanks!
@chrisholderness2504
2 жыл бұрын
I am about to swap my 1987 R10 Silverado with a 5.3L out of a 2003 GMC Yukon. How do I go about tricking the computer once I remove the emissions? Thanks in advance for any details you can share.
@sylumgand
2 жыл бұрын
OK 3 seconds in, gotta watch now.
@piratejetgarage
2 жыл бұрын
Lol thanks for checking it out!
@j.j.clingman4083
2 жыл бұрын
Hey pirates garage I just ran across your videos because I have a 1981GMC 1Ton 4x4 and I’ve been trying to figure out on what motor to put into it as soon as The motor that is in it now goes bad!! It’s just a 350 witch the truck was a fire truck at a fire station and baught brand new by the fire station also!! It has under a 100,000 original miles on the entire truck period!! It has the SM465 manual 4 speed tranny witch is by far my favorite trannies in older trucks!!! I’d like to ask if you could and would do a new updated video on what a person needs for hooking an LS motor up to the SM465??? Like what bell housing a person needs what fly wheel and clutch setup and even what a person can use for the linkage for shifting the tranny?? I no you can run a hydraulic setup or the regular linkages that were used originally from the square body style trucks!! I guess I’m very new to the LS stuff but I am definitely thinking I’d definitely like to try swapping a LS in a square body truck but definitely would like a little more info first before starting!!! Also we’re a person can buy those motor mount plates for swapping in a LS into a square body truck??? I definitely like those plates but not exactly sure where to buy a set from?? Also what is the best way for doing all the wiring for the swap??? Use the entire wiring harness out of the vehicle that the LS motor came from or just buy a wiring harness from someone that has made the harness smaller and just what is actually used for the swap and where a person can get a aftermarket wiring harness like that?? Any help would definitely be greatly appreciated really I’m serious!! They don’t look all that hard to swap looking at things now but just nowing where a person can get some of the different things from would definitely help me out a bunch!! The motor that is in this truck now just has a bunch of oil leaks but everything is got to be one of the tightest driving older trucks that I have ever driven for sure!!! I would definitely definitely appreciate it if you would do an updated video on some or all the different things I mentioned earlier in this and I also no that I’m definitely not the only one out there that would like to no also!!! I have guys asking me all the time if I no and I really just haven’t messed with any LS over the past 25 to 30 years that I have been messing around with the older trucks but I definitely am wanting to give it a try if you are willing to help with some of the info I may need??? Thanks again buddy and I really appreciate it!! Remember keep up all the hard work buddy!!! Loved the several different videos of yours that I have watched so far!!!!
@RcFlashlight
2 жыл бұрын
YO I have a truck exactly like this one! Never thought I would ever find another truck that looks like it! If I ever wanted to do an LS swap on it, just watch this vid.
@bighurkgkb4l745
Жыл бұрын
He got straight to it 💪🏾💪🏾🦾🦾
@galenyoung8349
Жыл бұрын
Can you use the the column & key(s) & NOT have to flash the, computer? Or, you just (no matter what) HAVE TO have the computer, flashed.
@MrJayo73
Жыл бұрын
You have to delete VATS
@galenyoung8349
Жыл бұрын
@@MrJayo73 you can bypass the, vats. The egr & the other bs, not so much. There's a tutorial on youtube that shows how to intercept the vats & totally DELETE that, system.
@mblake0420
2 жыл бұрын
Distilled water has mineral deficiency and will rob metal of its minerals and eat it, ask me how I know! Use premix, used to think it was stupid but it's all I use now.
@tonguedarts
2 жыл бұрын
Excellent video, thanks for sharing. Could you post the brand and part number of the fuel sending unit you used? The outlets are alot longer on yours than the Delphi branded '87 sender I recently installed on my truck, which would be nice.
@GagesGameChannel
2 жыл бұрын
Hello I’ve been looking for a long time. Trying to find out what pilot bearing id need and what flywheel to mount a older 5.3 to a 73 k10 4x4 sm 465
@OGSnipes2022
Жыл бұрын
You should put a Ls 8.1 in it
@luisordaz8616
2 жыл бұрын
Good video 💯 I been seen other videos but you explain pretty much everything thank you Wondering where are you located I’m interested in doing that on my 87 squarebody, but probably still too much for myself I’m in the chicago area.
@rustybottoms8859
2 жыл бұрын
Watched your K20 video and this one is a great wealth of information as well. Thanks so much for sharing.
@brandonknight7240
2 жыл бұрын
I doubt that whistle noise was coming from the intake gasket thats highly unlikely, probably coming from that cheap throttle body pipe setup
@Comm0ut
Жыл бұрын
Great video! I've a crew cab with a Century wheel lift that direly needs an LS 6.0/4L80e.
Пікірлер: 286