I would sure like to be able to get the measurements for this tree!
@donaldmaclean6238
5 ай бұрын
I built one. I made my stock 1 in thk with Parnell 20deg. Cuts on side. Large rectangle on bottom I made 14 in Long on top side. End angles are 20 deg as well. Made 14,12,10,8,6,4. Rectangles. 2 of each. Top I cut at 20 deg to make the point.
@emmanuellevargas7021
5 ай бұрын
it is a beautiful x-tree , it wokld be nice if he posted at least the angle of cutting ,and the high of the this trees .. nonetheless if we draw a x-tree on a big piece of cardboard the we want it ...from them we can get get the angle .....
@sneakyhippo8663
4 ай бұрын
The angle that was shown is the only one used throughout the whole build for the top. 20° 4-2x4s were used. That completes the top. As far as the Stand, that is something you could make with your own design.
@duane8363
4 ай бұрын
Hardshell woodworking. Has full build and instructions on how too.
@RamoneZuniga
5 ай бұрын
I would like to get plans for this build ❤
@bradyoung7292
4 ай бұрын
Very Nice! I just built this myself, and here's what I was able to figure out between the video, other comments below and my actual build (U.S. / Imperial units and lumber dims): Used 1x2 for everything except vertical base (1x6) and top cone (2x2). Ripped 20deg sides on 1x2's with table saw, removing as little material as possible. bottom of tree is 16-3/4" wide (16" pieces) followed by two each 14", 12", 10", 8", 6", 4", 3" and than top cone - came out a bit wider and shorter than this video, but the 70deg sides line up near perfectly to the top. Hardest cuts are ends of 1x2's, need a compound miter saw set at 20deg on the base and 7.5deg on the bevel. Flip 1x2's after each cut (watch video closely) and lumber direction matters - you'll have to experiment. Again, very cool and thanks to I wooden for posting this!
@iwooden2507
4 ай бұрын
good luck my friend
@laurentpfister2388
4 ай бұрын
Bravo et MAGNIFIQUE 👍👌
@edcarbone241
4 ай бұрын
Beautiful Work!! And I like your 3 combo saw!!
@iwooden2507
4 ай бұрын
Oh it's very good. 👍
@AllenOxendine
5 ай бұрын
Cool project, thanks for sharing
@iwooden2507
5 ай бұрын
Thank for watching
@dandagaiola4750
4 ай бұрын
Excelente trabalho ficou muito legal que Deus continue abençoando você e toda sua família amém 👪 👪 👪 👪
@iwooden2507
4 ай бұрын
Thank you so much
@quietspacearts
5 ай бұрын
love what you made here, maybe to stop wood falling to ground have a chair or hobby hors to rest the end of wood once almost through the saw that way you not have to bend yourself or damage the wood x keep on making x Vanessa
@iwooden2507
5 ай бұрын
Thank for comment!
@NarsiMan88
5 ай бұрын
Nice ❤❤❤
@elizabeteoffredi1642
4 ай бұрын
Arrasou ! Lindo demais ! Parabéns !
@danmoreton1788
4 ай бұрын
Outstanding!
@davidfleming1395
5 ай бұрын
Well done son merry Christmas nice video from Wales UK 😊
@iwooden2507
5 ай бұрын
Thank you so much 😊
@pathardage1880
5 ай бұрын
Outstanding. Very innovative. Thank you.
@iwooden2507
5 ай бұрын
thank you so much
@iwooden2507
5 ай бұрын
God bless you
@rajrooplal7595
5 ай бұрын
Fantastic, I love it
@iwooden2507
5 ай бұрын
Thank you so much
@sneakyhippo8663
4 ай бұрын
This is awesome and has potential for so much more. Thank you for a wonderful video and the inspiration! You did good work my friend!
@iwooden2507
4 ай бұрын
Thank for comment
@lidianelida9629
4 ай бұрын
Excelente trabajo, felicitaciones!!
@iwooden2507
4 ай бұрын
Thank for watching
@lindsaylavallee5012
5 ай бұрын
Well done … it’s beautiful !!
@iwooden2507
5 ай бұрын
Thank my friend
@alexreid4131
5 ай бұрын
Nice work! What finish are you applying at the end?
@BrianF.1969
4 ай бұрын
Very nice! I will be building a couple of these soon. Thanks for the video.
@iwooden2507
4 ай бұрын
thank for watching
@iwooden2507
4 ай бұрын
Good luck my friend
@noeldeweese4975
5 ай бұрын
Very nice build. Very original.
@iwooden2507
5 ай бұрын
Thank for watching
@lancelowery3081
5 ай бұрын
This is beautiful and i would love to build it! Where can i get the plans?
@dorothylehman4164
5 ай бұрын
Great job it's beautiful you did a wonderful job
@iwooden2507
5 ай бұрын
thank you so much 😊
@colinfreel1312
5 ай бұрын
Is your mitre blade tipped? At what angle? Love the build.
@wizpopr
4 ай бұрын
It would be great to know what the measurements are when cutting the pieces on the miter saw. And how many of each to cut.
@Pe.Pe.
5 ай бұрын
Sehr schön geworden 👍👍👍👍
@chuckross3243
5 ай бұрын
Very nice!
@gediminasmockevicius5994
3 ай бұрын
klasse - Litauen
@PLINKER
5 ай бұрын
super!
@MrTrecutter1
5 ай бұрын
Beautiful
@iwooden2507
5 ай бұрын
thank for watching
@ChalePousada-ig3hx
5 ай бұрын
Top muito top, vou fazer
@darrellbaker9184
4 ай бұрын
Thanks @bradyoung7292 I tried 7.5 ° on the bevel and 20° on the base I flipped each piece over however I always ended up with the inside joints having a gap and the outside joints the ends were proud off the sides. Is it possible that I started my first cut with the wrong edge against the fence? I had the 20° cut on the base so the top edge was tight against the fence. Wish I could figure it out. Any suggestions? Thanks.
@alessandrofranca7525
5 ай бұрын
Belíssimo trabalho parabéns
@iwooden2507
5 ай бұрын
thank for watching
@Chukavin
5 ай бұрын
Отлично!!! А у нас ёлки живые растут!!! Много!!!
@magaleemoraes8408
5 ай бұрын
Que coisa mais linda, parabens
@iwooden2507
5 ай бұрын
Thank you so much 😊
@eugenemarais9520
5 ай бұрын
what is the measurements you made the tree with ?
@osvaldocogollo2648
5 ай бұрын
Excelente proyecto podríamos saber las medidas de las piezas bendiciones
@Mukes4889
5 ай бұрын
Wow🔰
@aungmyat7242
5 ай бұрын
2:10 Fly something from your table saw.
@muddslide8829
5 ай бұрын
Measurements for this project and angle cuts ?
@junmiguelcarpenatorres7014
4 ай бұрын
Está muy bien pero... Antes de montarlo yo le doy una pasada de gasóleo a TODAS las piezas y lo dejo que se empape bien , después lo dejo secar y se barniza , en lugar de grapar se marca y se atornilla para poder desmontar
@iwooden2507
4 ай бұрын
Thank for comment
@victorapodaca679
5 ай бұрын
Wonderful. Do you have a cut list for this?
@iwooden2507
5 ай бұрын
44,42,40,38,36,....,4
@iwooden2507
5 ай бұрын
it also depends on the height of the wooden bar. I used 4 cm wood
@victorapodaca679
5 ай бұрын
Thank you. Merry Christmas!
@victorapodaca679
5 ай бұрын
I’m assuming your dimensions are cm.
@darrellbaker9184
5 ай бұрын
Was anyone able to figure out the dimensions? It's really nice I would like to make one
@chrissmith-wq6gr
4 ай бұрын
Check the reply to the first comment.👍
@27Brandis
4 ай бұрын
Do you have patterns for this tree for sale?
@ronlittle887
5 ай бұрын
Could I get the measurements, and the angles for this project?
@davebender8901
5 ай бұрын
From what I could see, the "table saw" aspect we well as the bevel, were on 20 degrees each. As far as the measurements, it seems that you could make it as big or small as you would like.
@user-ht9sj3ll9u
5 ай бұрын
what are the measurements
@user-ht9sj3ll9u
5 ай бұрын
I really want to make this can you tell me the measurements
@BeaSahlfeld-lu3pm
5 ай бұрын
I'll buy a set of plans if you can make them up
@esperanzaalegria1591
5 ай бұрын
Que medida tiene la primera basa? Gracias
@iwooden2507
5 ай бұрын
45cm
@bonniegiddis9636
4 ай бұрын
Are there patterns for this design?
@Ricks2Cents
4 ай бұрын
*Here is My Twist on Your Build!!! How did I Do?!?* *Making Wood Christmas Trees | 3D Geometric Christmas Tree | Step up Your Wood Working Game!!!* kzitem.info/news/bejne/sWtms4aks5d4lo4
@iwooden2507
4 ай бұрын
oh It's was great 👍
@Ricks2Cents
4 ай бұрын
@@iwooden2507 Thank You!!!
@iwooden2507
4 ай бұрын
Merry christmas and happy new year!🎆
@Ricks2Cents
4 ай бұрын
@@iwooden2507 Merry Christmas!!! Thank you for the Inspiration!!!
@adamgendreau6313
5 ай бұрын
Has anyone figured out the measurements?
@user-gq8fh1mi5p
5 ай бұрын
❤m
@iwooden2507
5 ай бұрын
👏🏻👏🏻👏🏻👍👍👍
@SPMech1
5 ай бұрын
👍👍👍👍👍👍👏👏👏👏👏👏👏👏👏👏👏👏👍👍👍👍👍👍
@osvaldocogollo2648
5 ай бұрын
Cuáles son los ángulos que se utilizan
@iwooden2507
5 ай бұрын
I use a 70 degree angle
@randyhoudashelt1239
5 ай бұрын
A little commentary would be nice, for those of us who aren't mind readers.
@MaximilianoCabrera-jy3ct
4 ай бұрын
🤔👍💪🇦🇷🇦🇷🇦🇷
@iwooden2507
4 ай бұрын
👏🏻👏🏻👏🏻❤️
@iwooden2507
4 ай бұрын
watch my next videos please
@lawlessjff
4 ай бұрын
I guess it shows you how he built one, but he won’t tell you how to do it
@garyperrin8172
5 ай бұрын
but you don't tell us how to make it no good
@antonkranjec3575
5 ай бұрын
Why is he wearing a mask? Is he sick?
@PapaFoxtrot2002
5 ай бұрын
How is that question relevant to the video? Are you being a COVID troll and unhealthy in the maturity department?
@antonkranjec3575
5 ай бұрын
Its an honest question.
@dhtango
5 ай бұрын
Dust. From the saw and sanding.
@melissaguer7641
5 ай бұрын
Want sawdust in your lungs?
@BAWOVINARollingPin
5 ай бұрын
Excellent. The video is on the exact topic I am seeking additional knowledge for my work. Your sharing is truly helpful to me. The content is clear, understandable, and very detailed. Thank you very much. Wishing you good health and success.
Пікірлер: 105