Yes sir , I had that idea as well only I am going to use header wrap and stove pipe with clamps ! ENJOYED..
@roccit
2 жыл бұрын
Nice! My old diesel rabbit vibrates those hose clamps off though 😂
@TheOriginalMechanic
2 жыл бұрын
I feel you. Sounds like a place for standard exhaust clamps.
@Blu-Man
2 жыл бұрын
@@TheOriginalMechanic hello want to ask you about a video you did on a 2010 toyota corolla around 5 yrs ago
@TheOriginalMechanic
2 жыл бұрын
@@Blu-ManSure, fire away
@Blu-Man
2 жыл бұрын
@@TheOriginalMechanic the 2010 Toyota Corolla you did 5 yrs back installing new headlight assembly did you have to adjust the height where is the adjustment screw ? And do you use led bright bulbs ?
@TheOriginalMechanic
2 жыл бұрын
@@Blu-Man I did not have to adjust the screw. I am not sure of its location and I no longer have this vehicle. I used standard replacement bulbs. Thanks for watching and I wish you luck with your repairs.
@jamesj.litteriojr.433
2 ай бұрын
Very Ingenious!!!!! 👍
@jonknust9784
13 күн бұрын
Thank you! I used the aluminum window screen, the high heat epoxy, some aluminum sheeting instead of stove pipe, the hose clamps and on top of all this, in the middle between the hose clamps, I used a 4” stainless steel band clamp to hold it all together. So far it is working great!!
@TheOriginalMechanic
13 күн бұрын
Good idea with the stainless band. I went that way the 2nd time.
@VictorRodriguez-vt1gy
3 ай бұрын
Great thanks
@frankrizzo6404
2 ай бұрын
If you cannot weld the certain metal, let JB do ot
@emailjwr
8 ай бұрын
Great video! Is this still holding up and quiet today?
@TheOriginalMechanic
8 ай бұрын
Thanks. This did require a redo just a few months ago. The gauge of metal I used was just too thin. This time I used a much heavier piece of sheet metal and I expect it will hold up much longer. Thanks for watching!
@kirkcramer6288
Ай бұрын
@@TheOriginalMechanic How did the hose clamps hold up? I am thinking that driving through the Michigan snow will loosen them up on my low-riding car.
@TheOriginalMechanic
Ай бұрын
@@kirkcramer6288 It wasn't the clamps but the sheet metal that corroded through. I redid it with much heavier gauge sheet metal.
@fisherprice6012
2 жыл бұрын
If u had power tools then there would be no use of speeding up the video😴
@TheOriginalMechanic
2 жыл бұрын
I have those but then I would have to find the tool, charge the battery, and cut the decibel level on the audio track. That's so much extra work lol
@stevewheatley243
6 ай бұрын
I used stovepipe on my resonator with band clamps. It beat paying $4-500 for new exhausts.
@kevinnava.7184
2 жыл бұрын
Awesome work.... thanks.🙋🙏🙋
@leodeboca
3 ай бұрын
good job!
@yungnewz28
9 ай бұрын
Can rtv go on the outrer edges for leakage?
@TheOriginalMechanic
9 ай бұрын
I don't think RTV, but exhaust sealant is a good idea.
Пікірлер: 31