I appreciate that you share all the methods so we can first build one and see if we like making them.
@thomasherlihy8670
3 жыл бұрын
Thanks for showing the entire process as well as discussing the silicone molds. I’m looking forward to trying some of these soon.
@CraftedElements
3 жыл бұрын
You are so welcome!
@benpress8884
3 жыл бұрын
Holy crap in my 45+ years of working with power tools I have NEVER seen someone rip a board on a table saw using the miter gauge.
@CraftedElements
3 жыл бұрын
LOL! Yeah its not the ideal use for it, but it works well to cut wonky edged boards.
@RosieNow
2 жыл бұрын
Thanks so much
@CraftedElements
2 жыл бұрын
You're welcome!
@1Down5UpOfficial
2 жыл бұрын
Thanks man!
@CraftedElements
2 жыл бұрын
Most welcome!
@cliffgrando859
2 жыл бұрын
Nice job Shawn! I've noticed that your blad on your saw was quite high when you were ripping your board. Careful buddy! Save your fingers
@CraftedElements
2 жыл бұрын
Thanks for the tip! We have a band-saw now for work like this, it was an older video.
@jessicatellier9270
3 жыл бұрын
amazing
@CraftedElements
3 жыл бұрын
Thank you! Cheers!
@KHALID_ALSULEMANI
2 ай бұрын
Thank you. Where can I buy adhesive tape?
@CraftedElements
2 ай бұрын
Amazon! or a local hardware store.
@waterlilly62lori
6 ай бұрын
What is this tape?
@psychoticcow5166
2 жыл бұрын
Do you remove the bark for anesthetics? I want to incorporate the bark into the design. If its a structural problem could I do a top coat of epoxy over a whole cutting board, or perhaps on the bottom layer do a full resin layer?
@CraftedElements
2 жыл бұрын
No, the bark needs to be removed before putting into the mold and pouring epoxy. Otherwise, the epoxy will just bond to the bark, and eventually it will just come right off the rest of the wood (the epoxy and bark will separate from the wood). So yes, its structural. However, yes, if you wanted to start with a resin layer first, then top coat after (essentially encasing the entire board in resin) then it might be feasible.
@TheStrouthMeister
Жыл бұрын
Should u use mold release in addition to this tape as well?
@lxix1067
Жыл бұрын
No you don’t need to, tape alone has worked just fine for me in the past
@TheStrouthMeister
Жыл бұрын
@@lxix1067 thanks
@michaelsherman1031
2 жыл бұрын
Nice video. How do you keep the resin from flowing under the boards in the middle?
@zuilok
2 жыл бұрын
You clamp them down or put a heavy weight on top of the boards. If the mould and the boards are nice and flat basically no epoxy is gonna get under, or at least no more than a thin layer that can easily be sanded off.
@CraftedElements
2 жыл бұрын
We weigh the wood down with hand weights to keep it from floating upward
@nelsonpacheco5114
2 жыл бұрын
is it ok to plane epoxy boards? I read it can chip your blades?
@CraftedElements
2 жыл бұрын
For sure. I have never seen epoxy chip or damage blades.
@cliffgrando859
2 жыл бұрын
Good afternoon Shawn, do you guys have any kind of molds for end tables? If so, what do YOU recommend? Shawn, do you overlap your tape on the other pieces of tape?
@CraftedElements
2 жыл бұрын
We do. Although end tables is general, we have 24x12, 24x24, 36x18, 36x24, 24x16 etc.
@cliffgrando859
2 жыл бұрын
@@CraftedElements thank you....and what is your website address
@CraftedElements
2 жыл бұрын
@@cliffgrando859 CraftedElements.com
@frankbelli1401
2 жыл бұрын
So I love these boards but epoxy isn't food safe so. How do you make it food safe?
@CraftedElements
2 жыл бұрын
There isn’t a way to make it “food safe” if it’s not already made as a food safe product.
@michaeldawes2152
2 жыл бұрын
Hi those silicone molds look excellent, do you ship to the U.K.?
@CraftedElements
2 жыл бұрын
Yes we most defintely do. Just add an item to your cart, go to checkout and a shipping quote will be provided.
@mariakeenan4908
3 жыл бұрын
Can you use any resin or does it have to be food safe?
@CraftedElements
3 жыл бұрын
Any resin would work with these molds.
@dieselkong
2 жыл бұрын
What’s the name of the tape used? Thanks
@CraftedElements
2 жыл бұрын
Tuck Tape (plastic sheathing tape)
@FiremanTy
2 жыл бұрын
What router lift is that??
@CraftedElements
2 жыл бұрын
Not a lift at all. Its a Mastercraft (Canadian Tire Store) brand router table, that i took apart and fit nicely into my Ridgid table saw.
@paulcappello560
3 жыл бұрын
your website does not open
@CraftedElements
3 жыл бұрын
Try craftedelements.com
@annaeleby2695
3 жыл бұрын
I purchased a mold like this so do I have to retape it and reseal it every time I use it or can I reuse it
@switchgear666
3 жыл бұрын
where was the time saving "trick"????
@CraftedElements
2 жыл бұрын
Not having to make a custom mold! Just use our silicone maker molds and keep on truckin’
@eldonbeyea393
2 жыл бұрын
Youhave your saw blade dangerously high
@CraftedElements
2 жыл бұрын
Ill be the first to admit I am a marketer and entrepreneur, before a pro woodworker :-).
@CraftedElements
2 жыл бұрын
Ill be the first to admit I am a marketer and entrepreneur, before a pro woodworker :-).
@KenLince
3 жыл бұрын
that hum in the background is incredibly annoying - might want to turn whatever that is off since you're not using a lav mic. Great videos though - much appreciated.
@CraftedElements
3 жыл бұрын
Sorry about that
@Itmovesme1
5 ай бұрын
yes your silicone molds are a better solution, but personally i think your company made them for wood and epoxy works who do this for a living thats why they are so damn expensive and i dont think there was much consideration given to your everyday home grown dyier.
@CraftedElements
5 ай бұрын
They are expensive because platinum cure silicone is expensive, because we make them one by one in our facility here in Canada. They weigh a lot compared to the general imported molds from Asia. You pay for quality. We aren't pricing them high just to serve businesses.
Пікірлер: 52