I agree, I used this film way back in the 80's when i could not afford solar film or mono-cote for large 1/4 scale models. I found a whole roll of this at 4' wide thrown away by a school and it lasted me like forever. It worked just as good if not better than standard covering in my opinion. And yes it will take a lot of heat and can warp even balsa structure if you keep shrinking it. I even spray painted mine and it did not peal.
@guidelinesR4pooCz
4 жыл бұрын
I know I'm a bit late in the comment section, but this video was very informal and was a really good guide for wing construction. Thank you so much!
@77Avadon77
4 жыл бұрын
Instead of hot glue use gliden gripper foam safe paint, wayyyyyy stronger and permanent bond. The stuff is insanely strong and amazing and unlike hot glue is not heat sensitive. Gliden Gripper cannot be build apart, the foam will fail first behind the glue joint!
@worldbestpilot
6 жыл бұрын
For larger wings take into account to add a thin layer of CFK rovings (not expensive) on lower and upper sides of the spars; these will take lots of load during (aerobatic) flying ! Have done that for numerous models and works perfectly !
@oneeyemonster3262
6 жыл бұрын
Im thinking about just adding ribs on top of a flat dallor tree foam board to prevent the wristing ( rather than just adding KF)..Use newspaper. postcard paper or whatever to skin the top so I can paint it. I have big sheets of drawing paper...it's slightly thinner than regular writing paper. There's so much stuff you can use if you dont have to worry about NITRO...I been collecting clear plastic (#2 plastic) from cakes...A couple more cakes..I'll have enough plastic to skin a 40' wing..lmao I'll have to experiment with full symmetrical ( fat rigs)...basically a foam board for the center,( sort of like KF4) So it'll have to make ribs for top and bottom. If it works...Im going to cut lighting holes in the center board..starting from the outter bays. For a 30 " - 40" 3d park fliers..it should be okay. Not going to burn holes in the sky...Just make the model twist and turn in a tight space. I need to make it 550 grams or less for a 36" 3D type models. it's recommended in the plans..Sort of like that grass hopper.lmao. That particular model has a flat bottom air foil ...basically I want to make something like the something extra scale down.lmao...They just have different air foils...that's all...Air frame, wing span..ect are all pretty much the same...just cosmetic If it works...I'll just use packing tape to skin it...Just put strips of postcard paper on top of the ribs..so the tape will have a smoother surface to stick to. hmmmm....maybe use heffy trash bags to skin it.lmao
@RenKnight347
5 жыл бұрын
Shear webs are placed in between the upper and lower spars forming an "]["-beam type construction just like they use in the construction industry of buildings. Aiding in minimizing certain specific forces and/or stresses being applied on the wing, as much as possible, while in flight is a paramount function of shear webs.
@fletchernicolas561
3 жыл бұрын
I know it's kinda off topic but does anyone know a good place to stream newly released tv shows online ?
@luciankendrick6642
3 жыл бұрын
@Fletcher Nicolas flixportal =)
@fletchernicolas561
3 жыл бұрын
@Lucian Kendrick Thanks, I signed up and it seems to work :) Appreciate it !
@luciankendrick6642
3 жыл бұрын
@Fletcher Nicolas Glad I could help :D
@dashtechnical
7 жыл бұрын
I've never done a comparison but I take it balsa is heavier than DTFB ? If I were to apply this method to, say, a FT design, could I expect any weight savings from building the wing this way vs. the normal "fold over" type of construction? I suspect I already know the answer, but I am not familiar with the characteristics of doculam. Great video! Love your builds!
@JoshuaOrchard
7 жыл бұрын
It really depends on the size. Smaller wings will more than likely weight the same. What you can expect is that you will have a more efficient airfoil over FT designs and use of this technique will lend itself in building balsa airplanes too. Paper on DTFB is heavy. This allows you to use foam without the paper and make a more scale airplane that will fly better than use of FT build techniques.
@luvmyTM1911
10 жыл бұрын
you can do a foam CF or FB sandwhich panel, but you need high density foam. The resins used for CF/FB are very strong and may leak through the styrofoam pores. The spar could be any material, balsa would suffice and will adhere with the hot glue just fine. If you have the money for CF why not =)
@biko9824
3 жыл бұрын
I’ve been searching for a video exactly like this for the next project, thanks!
@drampadreg1386
7 жыл бұрын
If I put that much into a wing, I would give it a coat of west systems epoxy rather than a laminating film. I would want to add some structural strength, and the weight is not an issue like a thick coat of gel coat would be. This is because I know that within 10 min after take off I would hit a goose head on or something and all that work would be fluttering down from the sky. The epoxy would give it a flying chance, at least save some of the structure rather than total destruction. That and I would be using those Estes rocket engines to get it off the ground and up to altitude fast, then they drop like spare fuel cannisters when the parachute charge goes off.
@620ironwolf
11 жыл бұрын
my dad and I make foam ribed wings just like this
@doodeep1
7 жыл бұрын
I loved ur idea!
@drampadreg1386
7 жыл бұрын
Another glue of you don't have a glue gun or just want to use something else that is very good with styrofoam is Gorilla Glue. Best glue I've encountered for styrofoam and you use very little since it expands 3 times it's size. Just moisten the surfaces and apply a thin film and I mean thin. The glue basically turns into foam itself it seems, and it's very strong and won't burn you either which is great if you're a kid. My glue gun only has high temperature so melts foam before it cools, that ain't cool!
@bayboos
9 жыл бұрын
Great tips, thanks for sharing!
@flightmonkey4225
9 жыл бұрын
Great tip! Thanks 😎
@chemistt
9 жыл бұрын
I dont want to flame nor troll but...Does this have any particular reason to do ribbed wing out of foam ? If you put so much effort into it...like cutting out ribs manually...isnt it better to use balsa instead ? Is it so much lighter ?
@JoshuaOrchard
9 жыл бұрын
It can be! The advantage is that its cheaper, faster, and sometimes lighter to build. If you mess up you really do not care because of the cost and time invested is not significant. You can cut out one rib in less than a minute whereas with balsa it takes several minutes to cut and sand to proper shape. You sheet of balsa will be about $5 for a 24x4" sheet where with this foam you can go to a dollar store and pick up a 20x30" sheet for a dollar. You can use that same foam for sheeting the wing as well. Its just a very versatile build medium. Thank you for having a look!
@chemistt
9 жыл бұрын
Joshua Orchard Eh I envy you the dollar store sheet ;) all I can get where I am from is depron and maybe some EPP etc...
@AFugal
9 жыл бұрын
I think weight is dependent on your design. Balsa is better if your worried about a nice plane. But for experimental planes this is the better route for cost reasons. Foam Board does a good job either way.
@iskandartaib
6 жыл бұрын
The foam wing would be lighter (a lot lighter) than the balsa wing even if you made the ribs thicker. I would NOT use foam spars, though, not even if this were for indoor rubber. While foam ribs would probably be OK for electric I would NOT do this for a glow powered model, it'd fall apart pretty quickly because foam has little compression strength. If you want to use foam for a glow powered plane you'd have to go with sheeted wire-cut foam cores rather than foam ribs (this is usually heavier than a similar sized balsa framework wing but is very strong and stiff).
@andrewshkolik
5 жыл бұрын
@@chemistt DTF is actually a depron, but covered with paper.
@AirCryptoTech
2 жыл бұрын
Great Actually I want make a plane What is the thickness or sizes of form board to make plane as beginners
@mentalvmaxrider
5 жыл бұрын
Very cool!! Thanks for sharing
@buzz60016
10 жыл бұрын
Hi Josh, excellent tutorial. Thank you for taking the time to help those who want to be informed. Doculam is an interesting material, will have to try that. On a separate note, I wonder if a thin strip of balsa, over the edges, to allow the use of other films. The weight penalty verses ease of other films ??? Also wonder if it is possible to use ribs from a balsa model as templates for the foam ribs ? Looking forward to your future build videos.
@Justwantahover
9 жыл бұрын
"I wonder if a thin strip of balsa, over the edges, to allow the use of other films. The weight penalty verses ease of other films ???" Balso is pretty light, and thin strips would be especially light. Other materials for covering (like tissue) would be much lighter than the office stuff (I think). It's a good idea (with the balsa edges) composite construction, but a lot of fucking around, that's all.
@JoshuaOrchard
9 жыл бұрын
Justwantahover Yes, tissue would be lighter. But not as strong. The film does act like a stiffener (torsionally). You sure could do balsa cap strips to use other films that use a higher temp. I would reserve this for much larger wings though. The balsa would greatly contribute to increased weigh with wood AND glue. The added strength would be great. The idea is not to make a wing that is overly strong. Just strong enough to get the job done. Obviously I'm not a proponent of over building models.
@MrCrisnana
7 жыл бұрын
Beatiful the work.
@FrankDoylezw
Жыл бұрын
Thanks for the video - really helpful. I presume you could create any airfoil you wish by just cutting the ribs to the right airfoil profile? I'm looking to create a Newman airfoil.
@JoshuaOrchard
Жыл бұрын
Sure! I've done this with numerous types of foils, semi and fully symmetrical. Undercambered would work well too though it may be more tricky to cover. For quick and dirty panels to try, you could simply how wire a foam core using templates and then spend the time on a built up wing like this. Lots of fun ways o approach it.
@FrankDoylezw
Жыл бұрын
@@JoshuaOrchard Thank you - I'll be giving it a try!
@TonhaoMastersBR
7 жыл бұрын
Hi my friend. So, Its sturdy enough to fly??? I REALLY loved this type of wing you teach, but please, Im a beginner, so what do you suggest for me to add more strengh to the wing?? How wolud I do that?? Thanks for the video!! :D
@JoshuaOrchard
7 жыл бұрын
Sure is! My SE5a uses this construction method and it works well. See that video on my channel. You can add strength by adding sheeting (foam or balsa) to the leading edge or add carbon fiber within the foam spar. Even thin ply would go a long way here.
@MarkPrimavera
4 жыл бұрын
Great set of tips, thanks for sharing. How do you cut your ribs? I'm thinking hot wire cutter?? The covering didn't look the tight in the video, can you get that material tighter? Thanks for sharing :)
@JoshuaOrchard
4 жыл бұрын
In this video, they were simply cut by hand. The new video I did cut them with a wire cutter but it's a bit different overall from this approach. The covering I used in this video did not shrink all that much because it is doculam... a document lamination film. Ultracoat or Monokote will indeed shrink more and tighten up more.
@titikolomongso4723
4 жыл бұрын
Nice to meet you and watching your videos. Indonesian people thanks
@tvideo1189
9 жыл бұрын
First, you got screwed paying 10 bucks for a couple of yards of Doculam (laminating film). It is available everywhere online for about 20 bucks per 250 foot roll. Second, that film will shrink a ton. You just never got it hot enough and left the covering slack. Laminating film will take more heat than MonoCoat or any other purpose-sold model covering film. Using it over foam ribs might not be the best useage for that very reason.
@JefftheDonkeyGuy
9 жыл бұрын
Great vid, enjoyed it immensely! Before I saw this I was wondering if a builder could use shrink wrap. Any opinions?
@JoshuaOrchard
9 жыл бұрын
Jeff McFadden I would think not. It expands and shrinks with the slightest temperature variation.
@JoshuaOrchard
11 жыл бұрын
I'm really not sure. I've never built one but I suppose if you reinforced the "hook area in the wing properly it would do fairly well. Use of kevlar, CF or glass as a skin would certainly help strengthen the peg.
@eugeniopesqueira1275
2 жыл бұрын
thanks good video
@silbernersurfer8264
6 жыл бұрын
Will it, if a covering film, for example the cheap one from Hobbyking, is used and shrinked, strengthen the wing?
@JoshuaOrchard
6 жыл бұрын
Not really strengthen, but it will make the wing more rigid.
@BennyCFD
9 жыл бұрын
Did you hand cut those ribs, or can you buy them pre-cut? I don't know how much load you're going to have, Would it be smart to use carbon rod in the middle as well as the foam ones?
@JoshuaOrchard
9 жыл бұрын
BennyCFD Yes, hand cut. Its far easier to cut foam over balsa. If you remove any film or paper than it is even easier. Yes, carbon would be good but depending on your application balsa or foam spars with shear webbing will be sufficient.
@jimmytiler5522
6 жыл бұрын
well done yeah Im with you just make it so it flies i dont need to spend hundreds of dollars
@Thexredpunisher
10 жыл бұрын
Can you make a video about how to put the foam board on the thing
@justwatchvidz
9 жыл бұрын
Can you paint the Lamination film? Or is poster paper better?
@marshal7102
7 жыл бұрын
Yes I have painted it before and it did not peal or flake. I used Rustoleum Spray enamel.
@jameshickman5299
4 жыл бұрын
I don’t understand. The paper peels off your foamboard so easily. The paper on mine comes off in little pieces.
@JoshuaOrchard
4 жыл бұрын
It's likely the humidity in my area. Try wetting a cloth and wiping the paper down before trying to remove it.
@jameshickman5299
4 жыл бұрын
Joshua Orchard I found an approach that works quite well: massive overkill. The wet rag didn’t produce much change, so I put a sheet in the shower, turned the water to full hot, and let it run for few minutes. That made it easier to peel the paper away. Having achieved some success, I applied More’s law: “If a little’s good, More’s better, and too much is just right”. I put a sheet in the shower and flooded it, adding a second sheet trapping water between them. I let them soak, reapplying water. After about an hour the paper wrinkled, and peeled off in one piece. I was left with a bare sheet of clean foam, with no effort. The paper has a slick finish and it takes heat, time and water to dissolve the adhesive. I realize this is a long post, but I hope this will help others. Let’s be careful out there.
@hendrickngobeni4799
8 жыл бұрын
How would you attach ailerons to the wing, and which material would you recommend ?
@JoshuaOrchard
8 жыл бұрын
Ailerons can be attached with any hinge material. You can insert a small piece of balsa on the inside of the wing if you have fears of it pulling free. I personally love to use old floppy disk material. Sand it a litte and any glue will hold it and it flexes nice too.
@senthilkumar9606
5 жыл бұрын
Thanks buddy
@MasboyRC
4 жыл бұрын
Thanks for sharing bro 👍
@ryanlemons3255
2 жыл бұрын
What transparent film would work for this kind of ribbed wing?
@JoshuaOrchard
2 жыл бұрын
My experience with covering films on foam at this point tells me that you really can use any of them but they are far more sensitive to temperature fluctuations. Do a test patch on some crap foam before you apply to the model and you'll be just fine.
@aztecwarrior6284
6 жыл бұрын
I agree have fun! can foam be fiberglassed? if how?
@JoshuaOrchard
6 жыл бұрын
It absolutely can be glassed. You have to be strategic about what cloth you use and where you use what weight of cloth. I frequently use 0.75oz cloth and waterbased polyurethane (WBPU) as a surface finish that is more paintable and gives a very smooth finish. Epoxy will give strength at more of a weight penalty. Perhaps I should do a video on my glassing techniques.
@CarminesRCTipsandTricks
4 жыл бұрын
@@JoshuaOrchard DEFINITELY!!! 😁
@waza474
7 жыл бұрын
are there any printouts of each piece that i can use as a template? i need to make one for school, thanks. :)
@JoshuaOrchard
7 жыл бұрын
This was just a demonstration section. You can use any airfoil you chose. In this example, I traced an airfoil from a balsa kit that I had completed.
@poucpouc9331
5 жыл бұрын
Very nice to teach kids before they use wood.
@shecter68
6 жыл бұрын
Nice concept but the covering looked like crap leaving all those wrinkles. I would have to cover it with a thin sheet of balsa to hide that hideous looking covering.
@JoshuaOrchard
6 жыл бұрын
Agreed, however in this video I was using doculam, which has very minimal shrink. Low temp coverings would work better. You can get the idea from the video that you CAN cover it but yes, 1/16 balsa sheet would also work very well.
@lenny108
6 жыл бұрын
but how do you get all the kerosene in that wing?
@vallicon
10 жыл бұрын
so a hair dryer wouldnt be hot enough to stretch the laminate cover?
@JoshuaOrchard
10 жыл бұрын
You could use it to shrink it but it depends on the covering. In this case, doculam does not shrink all that much. Other coverings can be more forgiving but usually require a hotter iron... something that will melt the foam too.
@frostyswine
11 жыл бұрын
In your opinion would a setup like this, but with a wood or CF spar, be able to handle a DLG launch?
@jasonnnnnnnnnnnnnnnn8352
3 жыл бұрын
Kinda tho
@AeroCraftAviation
6 жыл бұрын
What would a 1 meter wing with this construction technique weigh?
@JoshuaOrchard
6 жыл бұрын
Not very much!
@AeroCraftAviation
6 жыл бұрын
You think around 30-40 grams? Lighter? Heavier?
@JoshuaOrchard
6 жыл бұрын
Probably heavier if you consider reinforcements to keep the wings from folding. Any covering will add weight as well.
@AeroCraftAviation
6 жыл бұрын
I was wondering because I build wings from very thin A grain balsa and tissue covering and can get 1 meter wings as light as 28 grams, and I thought that maybe by some miracle this method could be lighter than mine. Super lightweight techniques interest me because I am always trying to make the slowest flying aircraft that I can....and cause my flying field is small, so if I like keeping my planes around they'd better be slow...
@Renaissance-fw1ox
8 жыл бұрын
a heat gun will melt it thay get verry hot
@ZezoG-jg1he
7 жыл бұрын
you didn't show how to build a full span wing using this method
@marshal7102
7 жыл бұрын
Its the same thing just bigger
@mfs5493
Жыл бұрын
Poor camera management.
@gman4229
9 жыл бұрын
is there any free programs to make the ribs for wings out there?
@JoshuaOrchard
9 жыл бұрын
Depends on the airfoil you want. You can readily use an online airfoil generator but if you are trying to design a whole panel you are looking at purchasing profili or compufoil.
@gman4229
9 жыл бұрын
just want to make simple wings for now,just like u did in ur video but a bit longer...
@JoshuaOrchard
9 жыл бұрын
felipe j. Garzon flitetest.com/articles/how-to-make-inexpensive-hot-wire-templates See the links to the airfoil generators linked in that article. They will generate basic NACA 5 and 4 digit series airfoils.
@ardvarkkkkk1
9 жыл бұрын
I have never used foam or plastic film (and never will) but when covering balsa wings, we never used to stick it to the ribs or spars. Just the edges. Les warpage when you shrink it.
@AeroCraftAviation
6 жыл бұрын
Yes but the strength gained is so small that it is worth losing in exchange for the exponentially decreased risk of terrible wing warpaing. Trust me, I've made the mistake of sticking tissue covering to the inner members of a balsa frame and shrinking it. That wing never flew...
@andrewshkolik
5 жыл бұрын
@@AeroCraftAviation with covering film you just have to warp your wing in opposite direction and heat film again.
@AeroCraftAviation
5 жыл бұрын
Yes, that’s true. But that has little do to with what I was saying. My point still stands.
@granttoye5852
6 жыл бұрын
What was that distance between spars?
@JoshuaOrchard
6 жыл бұрын
Spars or Ribs? Rib spacing, I think, was 1.5-2 inches. The spar was a single piece and webbing inserted between ribs along the spar.
@frantz4318
4 жыл бұрын
Is that possible to paint on top of the laminate?
@JoshuaOrchard
4 жыл бұрын
It is but I recommend that you prep the surface by roughing the surface with some fine steel wool.
@frantz4318
4 жыл бұрын
@@JoshuaOrchard thanks for your reply!
@stvrob6320
7 жыл бұрын
Could you sheet the wing with foamboard?
@JoshuaOrchard
7 жыл бұрын
Absolutely! When cutting your airfoil out, you would need to factor in the thickness of the foam.
@stvrob6320
7 жыл бұрын
Joshua Orchard I was thinking of doing just what you have done, except for a 1/8 inch x 3/8 inch balsa spar directly above and below the foam spar, plus 1/8 inch balsa at the leading and trailing edges. Then use (4) slabs of 1/8 inch foam for sheeting between the balsa members so its all flush. The foam spar would really be part of the shear webbing in that case.
@stvrob6320
7 жыл бұрын
Joshua Orchard If your wing needed to be tapered you could hotwire a much shorter version of the wing in the conventional way, but then cut it into slabs to use for your ribs.
@JoshuaOrchard
7 жыл бұрын
Yes, this is good thinking. Really all that we are looking at here is using foam as a different medium in balsa construction technique. It is easier to cut, less expensive, and has potential for very light aircraft without sacrificing too much strength.
@darrelldishman246
10 жыл бұрын
SWEET
@Thexredpunisher
10 жыл бұрын
How would you cover it and Styrofoam bored from Dollar store
@JoshuaOrchard
10 жыл бұрын
I do not have the time right now to do a video of it but perhaps in the future. I'm currently building a plane with this design so maybe after that. Basically you want to enlarge the leading edge to create a lip for the skin foam to butt up against. Apply glue to the ribs and tape the sheet in place that will be the skin. You may have to remove a portion of the ribs to account for the skin thickness. It will add a lot of rigidity and strength.
@JoshuaOrchard
10 жыл бұрын
FYI for you and others that have asked, see the following build log for sheeting with foam. forum.flitetest.com/showthread.php?11337-FFVS-J-22-Scratchbuild
@benjien2007
7 жыл бұрын
any model videos with this method
@JoshuaOrchard
7 жыл бұрын
My SE5a used this exact method: kzitem.info/news/bejne/xY2Ct3yoZoWnZYY Build details here: kzitem.info/news/bejne/yImCqIevi4x3rH4 My built-up funder and lightning used it similarly but I sheeted the ribs with more foam: kzitem.info/news/bejne/wIyEnY6he6eppHY
@FriesinNF
6 жыл бұрын
Do you live over a highway?
@JoshuaOrchard
6 жыл бұрын
LOL, not at all. This recording was done in my garage with the main door open on a rainy day. What you are hearing is cars driving by in the rain.
@santimazo4037
8 жыл бұрын
what is the "covery material?
@JoshuaOrchard
8 жыл бұрын
In this case I used Doculam. It is a film material designed for laminating documents at a low heat setting. It is also thinner than the higher heat laminating material.
@santimazo4037
8 жыл бұрын
very thanks, i gonna build an p38L with this type of wing
Пікірлер: 116