WoW!!! I didnt even knew that one should season the workbench from time to time.... live and learn!!
@JeanMinutile
2 жыл бұрын
Damn those look nice !!! They are simple and elegant !!!
@wiseoldfool
2 жыл бұрын
Looks terrific James!
@standswithfish
2 жыл бұрын
That walnut looks well seasoned, and now so does your bench!
@orellinvvardengra6775
2 жыл бұрын
“Marking gauge video next week” Me barely a minute and a half into making shakers “make it be here, now!” Lol! I’m really excited for next weeks video already, just reminded me of patten Oswald’s green lantern sketch.
@makermark67
2 жыл бұрын
I like the octagonal quite a bit better than the turned ones. Great work, James. Nicely done. Oh, and the saw file in the groove was perfect.
@glenallan815
2 жыл бұрын
Love it! Thanks James!
@ianpearse4480
2 жыл бұрын
32 of them and you could have a chess set for your cheese board and fill them with spices just to spice up the game a little. Lots of wood though. LOL. Love the simple but elegant look of those. Nice one!
@WoodByWrightHowTo
2 жыл бұрын
I like the way you think.
@ianpearse4480
2 жыл бұрын
@@WoodByWrightHowTo Loose a piece in the chess game and you get a hotter spice on the cracker and cheese as a forfeit. Or a random shake if you can't recall what spice is in which shaker! LOL.
@J.A.Smith2397
2 жыл бұрын
I like the sides rather then a round one! Great job
@athmostafa2462
2 жыл бұрын
Gorgeous .
@MCsCreations
2 жыл бұрын
Really amazing work, James! 😃 Thanks for all the tips!!! Stay safe there with your family! 🖖😊
@justplanebob105
2 жыл бұрын
Thanks so very much, James.
@Hansenomics
2 жыл бұрын
Weekend first!!!!
@michaels.8663
2 жыл бұрын
Wow beautiful job!
@Elderos5
2 жыл бұрын
I like the octagon better than round. Then corners on an octagon provides a better grip and fits the hand better. Never mind I don't have a lathe. You used the basic set with just the grinder bits here, right? I'm thinking ahead for Christmas ideas.
@raneolsen
2 жыл бұрын
Now you can grind your pepper with a grain of salt.
@Hansenomics
2 жыл бұрын
Scrap from Cremona? I need to up my game if that is on the scrap pile……
@WoodByWrightHowTo
2 жыл бұрын
He deals in very large pieces of wood. Lol
@JohnColgan.
2 жыл бұрын
nice build Mr James , good to see a complete build. Question on BLO. (apart from the obnoxious odour) used it properly 1st time on pine, once polymerised& dried, it appears to have a deep surface impregnation into the wood. Left surface beautifully smooth, no need for varnish!. & no brush strokes in the finish. Is it good enough to provide all weather protection to oak for outside use? if necessary can i varnish ovet the top? would you say yacht varnish or water based polyurethane?
@WoodByWrightHowTo
2 жыл бұрын
It does not work well as an exterior finish. It washes out pretty quickly. But yes, you can code it with a marine varnish or polyurethane. If using a water base polyurethane you want to make sure it's fully cured first. Or you could apply a thin coat or shellac in between to bind the two.
@JohnColgan.
2 жыл бұрын
@@WoodByWrightHowTo Great info thank you. Would you 7se it for a kitchen worktop or it wash out also? And use hard wax oil instead?
@tom314
2 жыл бұрын
Have you ever run into a problem with the salt drying out the wood causing cracking?
@WoodByWrightHowTo
2 жыл бұрын
I have not.
@michaelgreen429
2 жыл бұрын
Did the interiors of both the salt and pepper compartments get the BLO and paste wax treatment? or just the BLO? Thanks.
@WoodByWrightHowTo
2 жыл бұрын
Just the BLO on the inside.
@JackFright
9 ай бұрын
James, do you need to worry about wood type for this? For example, Rosewood is oily. Will that be a problem for pepper or salt to be stored in? Do we need a different finish on the interior in that case? Any other woods that might taint the salt or pepper? Want these to be food-safe and not go poisoning family by using a dangerous wood. Thanks!
@WoodByWrightHowTo
9 ай бұрын
Engine will know the small amount of contact would not be a problem for wood types. Even with the most oily woods they're not oily to contact as you would think about it.
@JackFright
9 ай бұрын
@@WoodByWrightHowTo Great, thank you!
@grbroussard
2 жыл бұрын
Awesome!
@thijspluis9998
2 жыл бұрын
Can you do some projects with the laith? I think that will be fun, also to copy, if you dont mind
@WoodByWrightHowTo
2 жыл бұрын
I've done quite a few lathe projects in the past. It's not my favorite so I don't do it very often, but every now and then it comes out.
@pettere8429
2 жыл бұрын
I thought you had these adjustable auger bits, will they not do that large diameters?
@WoodByWrightHowTo
2 жыл бұрын
Those can work. But they can also be an extreme pain. They also don't cut a flat bottom.
Пікірлер: 35