I made this car and it worked the first time! Be sure to check the Circuit Diagram because the video doesn't show all the correct instructions. Front right wheel was turning the wrong way but that was a quick fix. And the controller app changes left/right with forward/backward. But it still drives and that's sweet.
@DIYBuilder
3 жыл бұрын
Nice work!
@raijko9918
2 жыл бұрын
did you need to make any changes to the code? Couldnt get it working for me
@asmasayyed7247
Жыл бұрын
Hey can you help us..
@sheezarani3047
Жыл бұрын
Hey can you help me please in designing
@goldencat8709
Жыл бұрын
Bro can you share the code cause I cannot open it
@deepakhere233
2 жыл бұрын
Awesome project. Easy to learn and best for beginners. Btw, have you written that code yourself? It's easy to understand too. It would be helpful if you explain what your code does in the video too. Because, most youtubers just say "COPY CODE FROM DESCRIPTION BOX!!!". And, that's not what a learner should do. Thanks for this video btw.
@theshadyaccountant007
Жыл бұрын
agree 10000%
@FizPhysVideo
Жыл бұрын
Why not?
@pianovision6852
Ай бұрын
If your car is not running, even after connecting by phone ,you can add ( 4700uf 25v ) capacitor to motor driver input. And connect your Bluetooth module to direct Arduino Uno's positive and negative if your phone is disconnecting always after few seconds, and also add ( 470uf 25v ) × 2 capacitors in parallel to that bluetooth module and Arduino's positive and negative, and after this all remove that jumper from the motor driver and give another same power supply to direct Arduino Uno, this all things will guaranteed solve your problem.
@Parthaspartan1985
5 жыл бұрын
Works like a charm .. Code 100% working. A slight problem is that bluetooth app is disconnecting frequently.Can you help in this regard??I am using all the specs you have used and 18650 batteries also. Thanks for the good work...
@mohithkumar933
5 жыл бұрын
Same problem
@Parthaspartan1985
5 жыл бұрын
@Ujjal Padhan Normal Jumper wires.Purchased from amazon.Then Cut a pair of female jumper wire.Add the female end to the bluetooth module and solder the other parts to shield board Rx Tx point.
@Parthaspartan1985
5 жыл бұрын
@@mohithkumar933 Hello.. I have identified and solved the problem.The bluetooth module is not getting enough current from the shield board. While experimenting, I just connected the 5V pin,Gnd pins direct to arduino output pins just direct below the shield,did not solder it. Add a powerbank to the main arduino board.Pull the jumper from the l293d shield.And the bluetooth stays connected for ever.
@BabluKumar-dw2qx
4 жыл бұрын
Send the code bro plz in the comment
@anargyasatya259
2 жыл бұрын
@@Parthaspartan1985 i have a question,The app shows that hc 05 is connected and the blinking of the led in hc 05 also slows down(Red colour) .But when I try to control it doesn't move,what is the cause?
@imtiazrahman385
4 жыл бұрын
finally made it with HC-05 module. To the viewers don't use HM-10 module , u can't pair it with ur android.
@shirajulislam4269
4 жыл бұрын
can i use hc-06??
@ManusWorkbench
4 жыл бұрын
Hi brother, First of all vedio was awesome. I have a doubt. Can we use HM10 Bluetooth module instead of HC05. If yes, is there any connection changes or code changes. It will be good if know that. God bless u
@saranyabalasankar6568
3 жыл бұрын
if u connect HM10 It will not pair to android
@benjaminanangfio219
2 жыл бұрын
Thank you very much for the tutorial... I loved it I have one problem. After making it, I have to give it a push before it can move and when it hits an obstacle, it stops. Can you please help me
@benjaminanangfio219
Жыл бұрын
I realized the battery wasn't supplying enough power so I added up more battery and it worked perfectly 😊
@Kusalsumedha
3 жыл бұрын
It works.❤️. Small issue when i press forward sometimes it keeps going even if I release the button. Same happens to other sides. How do i stop continuous running issue. Thanks. Appreciate it
@swarnavamazumder8830
3 жыл бұрын
Your Bluetooth module is not good
@ankitnandy986
2 жыл бұрын
Hello bro. I have the same issue before but after that my car is working. You can follow my steps- 1)first attach the shield then upload the code. 2)attach your bluetooth module to the 5v and gnd (not the 9v).and tx to rx and rx to tx. 3)use a minimum of 5volts 1 ampere power supply(I used a powerbank)
@ankitnandy986
2 жыл бұрын
I hope it will work
@YashJain-qh5tn
2 жыл бұрын
Check the code again
@ramkrushnasolanke3215
2 жыл бұрын
@@ankitnandy986 Hi I also interested to make it can you please help me
@mdwashimansari6790
5 жыл бұрын
Awesome bhai.. 🤗🤗 Toy for my son will sorted.. 😂😂
@DIYBuilder
5 жыл бұрын
😂😂😂 thanks bhai
@ishanikaushik9059
4 жыл бұрын
@@DIYBuilder please send the code in the comment box as I can not get the code from your given link
@gingerwasabi8993
5 жыл бұрын
Hi DIY Builder, thank you for sharing this wonderful video. Nice work. I just built it today, but now I have encounter issue: No action and no movement after connecting with BT module (HC-05) with my cell-phone. Would you please share us more information base on BT module settings? for instance, BT roles, UART rate, and other setting as well. Thanks.
@DIYBuilder
5 жыл бұрын
Did you install AF_Motor library at first? If you are using the same motor driver shield then you have to install it's library otherwise the car won't work
@gingerwasabi8993
5 жыл бұрын
Yes, I already installed AF motor library before building this project. Also, I am using the same motor shield. Did you setup your BT baud? or other related setting? Thanks.
@DIYBuilder
5 жыл бұрын
Which app r u using to control the car?
@gingerwasabi8993
5 жыл бұрын
I used the APP that you provided.
@DIYBuilder
5 жыл бұрын
Then it should work bro
@wtltechnologiesinc.6051
2 жыл бұрын
Thanks for the video. Tell me, what are size of the screws you used (dimensions)? Where did you get the black acrylic sheet from? If you could put these few details in the description, others would surely be blessed to know as well.
@engineeringforourlife363
3 жыл бұрын
Dude thanks so much man I made it and it works I could not figure the codes out until I found your channel I made all my freinds subscibe bro thx so much
@DIYBuilder
3 жыл бұрын
Glad I could help
@kvrkvr7231
3 жыл бұрын
Bring how to install coad
@mohammadtamim3732
3 жыл бұрын
Hey bro can you help me with my one, it doesn’t work
@alessandrobelcari8376
3 жыл бұрын
One question, how do I know if my hc 05 have a inbuilt logic level converter?
@XPLOOD_X4
4 күн бұрын
Same
@arunetikala6817
5 жыл бұрын
Osm video🤘🤘.Excellent demonstration.plz explain how to make a drone using Arduino UNO or Raspberry Pi.....
@seanocansey2956
5 жыл бұрын
Not a great idea using an uno because they're not really powerful enough for flight stabilisation, but Quadcoptors or drones are really difficult to design and your better off buying a DIY kit. Besides weight and center of mass can change the performance of the drone significantly, meaning if he made one and you copied it and it wasn't the exact same, you'd have to change the code a bit. Anyway best of luck with what you want to build though 👍🏾
@deepakbains6755
4 жыл бұрын
Sir I liked your project..I also made same with your help by this video.. everything works properly but in back and left function only three tyres works.. forward and right function is very well works
@DIYBuilder
4 жыл бұрын
i think there is a problem with your motor driver. which battery r u using bro?
@deepakbains6755
4 жыл бұрын
@@DIYBuilder can we use l298 motor driver with same coding
@deepakbains6755
4 жыл бұрын
@@DIYBuilder I am giving power to Arduino board by power adopter and usb cable both..
@_.Apocalypse._
5 жыл бұрын
Can I use these motors and use same code? Single Shaft TT Motor size: refer to the picture above Operating voltage: 3V~12V DC (recommended operating voltage of about 6 to 8V) Maximum torque: 800gf cm min (when it is 3V) No-load speed: 1:48 RPM:200(when it is 4.5V) Load current: 170mA (when it is 4.5V) This Mini Electric Motor is a general purpose motor, work with batteries or solar cells perfectly Great replacement for the rusty or damaged DC gear motor on the machine. Used for electronic fans, electronic machine, toys, cars, robots, arduino projects, etc With EMC, it has strong anti-interference ability and causes no interference to micro-controller
@shutdahellup69420
5 жыл бұрын
you can use any dc motor.
@avamandal1964
4 жыл бұрын
I cannot download the audio calling please send me the order no coding link
@amartechs9267
4 жыл бұрын
Yes of course if you put any motor it will work.Maybe it might not move due to the weakness of the motor
@hariiyi3323
5 жыл бұрын
what wire did you use to connect the bluetooth module and the motor driver?
@arbro9889
4 ай бұрын
Jumper
@aaryasudarshan4251
5 жыл бұрын
i need this for a school project
@ver-teg712
4 ай бұрын
same
@user-cg6go7jh1l
Жыл бұрын
thank you very much i had a project to do with my school this video helped me at the right time, thank you
I have completed this project and this cost me around 3.5k(ofline stores).before beginning you should upload the code to arduino and then put the motor driver shield and etc .
@ashish835
5 жыл бұрын
You should have purchased it from Amazon I got everything in 2k
@ashish835
5 жыл бұрын
@Prathmesh Gumal //Arduino Bluetooth Controlled Car// //// Before uploading the code you have to install the necessary library// //AFMotor Library learn.adafruit.com/adafruit-motor-shield/library-install // #include //initial motors pin AF_DCMotor motor1(1); AF_DCMotor motor2(2); AF_DCMotor motor3(3); AF_DCMotor motor4(4); char command; void setup() { Serial.begin(9600); //Set the baud rate to your Bluetooth module. } void loop(){ if(Serial.available() > 0){ command = Serial.read(); Stop(); //initialize with motors stoped //Change pin mode only if new command is different from previous. //Serial.println(command); switch(command){ case 'F': forward(); break; case 'B': back(); break; case 'L': left(); break; case 'R': right(); break; } } } void forward() { motor1.setSpeed(255); //Define maximum velocity motor1.run(FORWARD); //rotate the motor clockwise motor2.setSpeed(255); //Define maximum velocity motor2.run(FORWARD); //rotate the motor clockwise motor3.setSpeed(255);//Define maximum velocity motor3.run(FORWARD); //rotate the motor clockwise motor4.setSpeed(255);//Define maximum velocity motor4.run(FORWARD); //rotate the motor clockwise } void back() { motor1.setSpeed(255); //Define maximum velocity motor1.run(BACKWARD); //rotate the motor anti-clockwise motor2.setSpeed(255); //Define maximum velocity motor2.run(BACKWARD); //rotate the motor anti-clockwise motor3.setSpeed(255); //Define maximum velocity motor3.run(BACKWARD); //rotate the motor anti-clockwise motor4.setSpeed(255); //Define maximum velocity motor4.run(BACKWARD); //rotate the motor anti-clockwise } void left() { motor1.setSpeed(255); //Define maximum velocity motor1.run(BACKWARD); //rotate the motor anti-clockwise motor2.setSpeed(255); //Define maximum velocity motor2.run(BACKWARD); //rotate the motor anti-clockwise motor3.setSpeed(255); //Define maximum velocity motor3.run(FORWARD); //rotate the motor clockwise motor4.setSpeed(255); //Define maximum velocity motor4.run(FORWARD); //rotate the motor clockwise } void right() { motor1.setSpeed(255); //Define maximum velocity motor1.run(FORWARD); //rotate the motor clockwise motor2.setSpeed(255); //Define maximum velocity motor2.run(FORWARD); //rotate the motor clockwise motor3.setSpeed(255); //Define maximum velocity motor3.run(BACKWARD); //rotate the motor anti-clockwise motor4.setSpeed(255); //Define maximum velocity motor4.run(BACKWARD); //rotate the motor anti-clockwise } void Stop() { motor1.setSpeed(0); //Define minimum velocity motor1.run(RELEASE); //stop the motor when release the button motor2.setSpeed(0); //Define minimum velocity motor2.run(RELEASE); //rotate the motor clockwise motor3.setSpeed(0); //Define minimum velocity motor3.run(RELEASE); //stop the motor when release the button motor4.setSpeed(0); //Define minimum velocity motor4.run(RELEASE); //stop the motor when release the button }
@ashish835
5 жыл бұрын
@Prathmesh Gumal nobody can help you by send you are motor library you need to download it yourself
@BabluKumar-dw2qx
4 жыл бұрын
Send the code bro plz
@farukhossain3719
2 жыл бұрын
@@BabluKumar-dw2qx given. Chk it
@drifter1949
4 жыл бұрын
I have just finished building this project and it works very well, thank you for all your work. Is it possible to have proportional motor control using the motor shield. If anyone could suggest any links on how to do this I would be grateful, thank you.
@sheikhfahim9500
4 жыл бұрын
bro what is that plug used in the bluetooth ?
@gfsjkdkl
2 жыл бұрын
Sir, I also car materials I have just finished buliding this project.But the problem is not moving. You would help to me
@darkfiregaming9921
2 жыл бұрын
@@gfsjkdkl I have built my project but bluetooth dosent work please give me solution.
@asmasayyed7247
Жыл бұрын
Can you help us..
@atlboysNo
Жыл бұрын
Thank You A lot bro. In every of our school project I take projects from you. My group always gets good remarks for the project. We are now selected by IIT - Mumbai in India. Thanks aa lot. 😃
@DIYBuilder
Жыл бұрын
Wow, congratulations man 👏
@whyzekid
Жыл бұрын
Is the controller app on Iphone
@vishnumaxz0763
Жыл бұрын
@@whyzekid may be 🤔
@criticalencountergaming9333
3 жыл бұрын
May channel reach 10 million soon
@jackytank
5 жыл бұрын
Hey ! I'm a newbie to Arduino and I just want to ask you some silly question ! What is that heating device you use to heat up small metal electronic part .. I really don't know how it's called ? Thank u .. 1 like from me ..
@jackytank
5 жыл бұрын
i knew it now... :)
@Tarun_Kotagiri
5 жыл бұрын
tell me what it's called....😜
@celestialjunipers6829
4 жыл бұрын
It's a soldering iron for those who do not know
@akulapraveenkumar9482
2 жыл бұрын
It is soldering machine
@lucky1586
4 жыл бұрын
Hii , bro can you show me the coding part plz 🙏🙏 Arduino is new to me
@alyhussam2570
2 жыл бұрын
It is in the description
@Gm-vq6rx
Жыл бұрын
Where is the resistor in the video
@spottedchannel5821
3 жыл бұрын
Great work !!.....can you please make a video on automatic and manual modes of operating of any one of the actuators using NODEMCU.... please
@abhisheksahani4065
5 жыл бұрын
How to install code please make one video
@worldofcircuits7157
3 жыл бұрын
Will the setup work with 9v rectangle battery????
@MS_Techno_Beast4
7 ай бұрын
No it will be over heating
@supersaiyangod4166
7 ай бұрын
Hi DIY Builder, thank you for sharing this project with us :) The link to the controller app just takes me to a page that says "we're sorry, the requested URL was not found on this server" even though i use a samasung phone. Would you mind to please share the name of the app or an updated link with me please?
@pedisimos
4 жыл бұрын
Please help me with the lights, what pins do I have to use to connect them?
@Justinenert
5 жыл бұрын
Can you please do a video on a car 🚗 that follows you thru GPS
@tonymillward3755
4 жыл бұрын
I would also be interested in that....
@cessposter
3 жыл бұрын
do you have any idea how much time and electricity to move that far
@Rbasakl
7 ай бұрын
Please give the app links the link is not working
@FlapNicky
3 жыл бұрын
can I use the L298N instead of the Motor Driver Shield
@gintaskacinskas1752
2 жыл бұрын
Hi DYI Builder, thanks for the project! I am having a few issues.... 1) HC05 continues to disconnect after a few seconds. Using 2x 3.7V 18650 batteries to power the car. 2) Only M1 and M2 motor shield ports work. I have tested the motors and they are all fine. Also have managed to get all 4 motors running connected 2x to M1 port and 2x to M2 port, so the problem seems to lie with the ports themselves. Any suggestions on how to identify the actual issue and resolve it?
@ankitnandy986
2 жыл бұрын
Hello bro. I have the same issue before but after that my car is working. You can follow my steps- 1)first attach the shield then upload the code. 2)attach your bluetooth module to the 5v and gnd (not the 9v).and tx to rx and rx to tx. 3)use a minimum of 5volts 1 ampere power supply(I used a powerbank).
@ankitnandy986
2 жыл бұрын
I hope it will work
@LegendGuy
2 жыл бұрын
@@ankitnandy986 Bro i have A question see if i mount motor shield on arduino then how much volt will it supply to arduino means i give 9v to motor shield then how much volt it will give to arduino
@ankitnandy986
2 жыл бұрын
As much as i know. If you give 9v to ur sheild then arduino will also receive 9v. But you can measure through multimeter (vin and gnd pins)
@jethalalgada4299
2 жыл бұрын
Hello bro please help me I have the same problem I have attached all the things as per the circuit diagram but the problem is that when I connect the hc-05 within one or two seconds it get disconnected and in that 1 or 2 seconds also the car is not working, please help me, this is my final year university project
@adityavarghese3339
4 жыл бұрын
The app shows that hc 05 is connected and the blinking of the led in hc 05 also slows down(Red colour) .But when I try to control it doesn't move
@bhushanghevde15
4 жыл бұрын
same problem man please tell solution
@anargyasatya259
2 жыл бұрын
same of me do you know how to fix it?
@anaghroy-9681
4 жыл бұрын
please, make a video about connection of lights in this OA car. I mean it will work like a indicator.When the car go forward,the forward light will on.When the car go back,the backward light will on.When the car go right, the lights of right side will on.Can you make some thing like this?
@Mryash-ds6tk
Жыл бұрын
Superb Project! But did anyone notice the car falling from the table 😂😂at last and even he said something, if not then check it.
@hisahil7884
4 жыл бұрын
i have this error exit status 1 'motor1' was not declared in this scope what do I do pls help
@samjn08
5 жыл бұрын
Nice vudeo (first viewer)
@DIYBuilder
5 жыл бұрын
Thanks man :)
@adityasinha1676
2 жыл бұрын
We are follow this video, but when we connect motor driver sheild , we saw it is different from your moto driver sheild , how you got those pin near "Ad5". In our sheild there are no pin.
@sumanpingme3535
2 жыл бұрын
same question
@shrutipatil5452
4 жыл бұрын
We can use single jumper wires for connecting Bluetooth module
@HobbyRoom
5 жыл бұрын
Cool project bro. The acrylic battery case was a good hack too..
@DIYBuilder
5 жыл бұрын
Thanks bhai 😁
@divyanshsrivastava3232
4 жыл бұрын
@@DIYBuilder where did you connect Battery wire
@hariprashanth2480
5 жыл бұрын
Can you help with my app , it's frequently disconnecting with bluetooth module
@DIYBuilder
5 жыл бұрын
Which battery r u using?
@mohithkumar933
5 жыл бұрын
Same problem
@MrInvencibleBro
4 жыл бұрын
@@DIYBuilder 9V can type battery
@chinmaysukumaran3263
4 жыл бұрын
Same problem. Using 9v battery
@sefawinter
4 жыл бұрын
I have the same problem. I'm using 5X AA rechargable batteries.
@thomassigitsujatmiko9630
3 жыл бұрын
good idea....how about coupled with two servo for clamping lift waiting for the tutorial
@SKY-pl7ni
2 жыл бұрын
Nice work! I wanted to ask can we use about 3v
@AlexNurton
5 жыл бұрын
How do you make the diagrams? Make a video on how. Please
@ujjwalkachhap6387
4 жыл бұрын
How did you get that 5v and gnd pin in motor driver
@prakashbagul2891
3 жыл бұрын
love from kolhapur
@DIYBuilder
3 жыл бұрын
Thanks
@7dayscraft
5 жыл бұрын
Nice video #7dayscraft
@wan_1229
5 жыл бұрын
thanks for the code link, can you provide circuit diagram
@DIYBuilder
5 жыл бұрын
Ok bro i will update the circuit diagram soon
@sachitkumar4913
5 жыл бұрын
@@DIYBuilder i also need it please. ..
@praveenkumar8126
5 жыл бұрын
Is this code working...?? But in my case this is not working...
@johnaziz4742
4 жыл бұрын
hi friend thanks for project i do every thing but when i disconnect USP cable the Bluetooth module lost power and make disconnect with my phone pleas help me
@DIYBuilder
4 жыл бұрын
contact me on instagram
@ramonedrozojr.768
3 жыл бұрын
@@DIYBuilder meee too, it said that device connection was lost. Please help
@societytoday5975
2 жыл бұрын
@@DIYBuilder I dont have Instragram Could you answer it here
@swarnavamazumder8830
3 жыл бұрын
HI SURAJIT ! CAN I US ARDUINO NANO FOR THIS PROJECT IN THE PLACE OG ARDUINO UNO WITH THE SAME CODE ?
@prabhatigupta4833
3 жыл бұрын
Does we have to remove PWR jumper in this project??
@mirandajosefabian1854
5 жыл бұрын
A question after loading the programming to the arduino disconnects the usb from the pc and presses the switch, or does one more procedure?
@DIYBuilder
5 жыл бұрын
You don't need to do anything after uploading the code.
@palashpratimmandal7905
4 жыл бұрын
Why code is not viewing in the link given
@tommicava9675
5 жыл бұрын
Can I use the iOS app "BitBlue" with this project? Or I have to use a different Bluetooth module or something else? Thank you
@DIYBuilder
5 жыл бұрын
actually i didn't use it before. but you can try
@adisuyash
5 жыл бұрын
iOS can’t connect with hc05
@indiandiymaker5143
3 жыл бұрын
@@adisuyash yes
@elnetcho
10 ай бұрын
i made it but i have a problem, when i turn it on and connect it fast to my phone it works for 2 seconds and then stops working, i replaced the batterys whit a rechargable 9 volt battery, so can anybody tell me if that is the problem or how can i fix it please Edit: i think its the milliamps difference, can anybody please confirm, in the video and in the diagram it shows 5 Amps and i only place in it 400 Milliamps Happy edit 2: turns out it was the motors, what a headache but i finally got an bluetooth rc car, next im turning it into a battlebot
@unnikannanbr
4 жыл бұрын
Can i use 9v battery instead?
@kuldeepsuthar1633
5 жыл бұрын
How to enter the code in the last of video please make video on this.
@adityatiwari8381
4 жыл бұрын
Yes
@TotalWarChronicles
5 жыл бұрын
nice man! can you give me the measurements of your wooden plate? both from the battery holder and the wooden plate itself?
@alliswellyt8912
2 жыл бұрын
Can you teach me how to download af motor library because I am kid i am doing this for my school project my deadline is December 12 please reply soon
@manusunny3395
5 жыл бұрын
Nice build brother ... Which app are you using for controlling the car.. ?
@DIYBuilder
5 жыл бұрын
Thanks bhai i will update links soon
@immysoun
5 жыл бұрын
iOS I think the app is Ble Mini Car
@abhishekk3561
4 жыл бұрын
Sir please make clear videoof installing code to arduino....
@roggaming6112
4 жыл бұрын
I am also so suffering this problem
@blackjesus_699
5 жыл бұрын
the code is not working
@bobshow7398
5 жыл бұрын
here is perfect tutorial step by step www.instructables.com/id/Simple-CAR-Arduino-Bluetooth-Controlled/
@noxious1241
2 жыл бұрын
have you solved the code yet?
@shailasultana9535
Жыл бұрын
You do not download the motor driver shield library yet
@endgamey
5 жыл бұрын
can i ask if i rest my arduino & motor driver board on an acrylic block will the uno or motor driver board burn ? cause i know if i rest them on my metal chassis its said that they would burn.... REQUIRE A REPLY ASAP THANKS IN ADVANCE
@rayd4281
4 жыл бұрын
Really cool. You really should have more subscribers than you have.
@DIYBuilder
4 жыл бұрын
yeah bro
@wilmermendez4187
5 жыл бұрын
Thanks for this tutorial bro!,
@gabrielfranciscoacostaguer8318
2 жыл бұрын
Full code please
@soujanpoojari1605
4 жыл бұрын
Sir can we use regular batteries like 9V cell??
@sreeharismulticraft2451
2 жыл бұрын
i bought a new motor drive but the motors are not spinning i did all correct i guess but not working
@Forcasper228
5 жыл бұрын
Hey bro! Nice video. Can you please tell what changes in the code should I make to run Arduino mega? please help bhai.
@DIYBuilder
5 жыл бұрын
You don't need to change anything in code. just select correct board and port while uploading the code. In my opinion arduino uno is better option instead of mega.
@indiandiymaker5143
3 жыл бұрын
@@DIYBuilder yes you are right
@opaldaisuke9979
5 жыл бұрын
Hi i have an problem on making arduino car like this, i already create a model with motor shield,motor gear and clone arduino , the problem is all of the motors run slowly(even my code is correct) thus the problem is the motor shield?, the clone arduino? or im just lacking of power supply (im using 6000mAh, 5v and 2A power bank) I really need your help since my Science IP is robotics.
@shashanknag5778
5 жыл бұрын
Same problem here
@BabluKumar-dw2qx
4 жыл бұрын
Bro upload the code
@alexanderbourne4708
4 жыл бұрын
Hello Would x4 AA batteries run the motors?
@stanisawurbaniak2299
4 жыл бұрын
Hello , I have just finished building this project ,I have problem bc my car when turn left right or do some move he cant stop he go gogo and go only way i can stop him is off power please help me
@adityajyothiraj7342
4 жыл бұрын
Same problem
@kaziemtiaz4952
4 жыл бұрын
Could you please send me the information code personally. I'm unable to find it. Please help me.
@girisathvikreddy9517
4 жыл бұрын
Same
@yabztek2417
4 жыл бұрын
@@girisathvikreddy9517 Hello there! I've created a similar video on my channel that might help you out, if you still have questions I'll be happy to help you out :D
@aplicarciencias
4 жыл бұрын
Thank you! You help me much!
@dakshaidasani6981
2 жыл бұрын
I have a question about tutorial, what does he do with the slide switch and what is that pink wire he connects to it?
@abhishekprajapat6008
Жыл бұрын
He connect with the Dc switch . For turning on off the current in future. He connected 2 wire , white and pink . One ground can be directly connected to the shield and pink wire which is power wire is connected to switch with battery and another wire connected to switch from switch to shield
@pinkyrajak3784
3 жыл бұрын
Which software or app do you use for making circuit diagrams
@harshshukla4700
5 жыл бұрын
nice finishing bro
@DIYBuilder
5 жыл бұрын
Thanks bhai 😊
@astro538
3 жыл бұрын
Which software are you using to make the circuit diagrams?
@lekshmisarath6820
2 жыл бұрын
Ardino ide
@kalashdesai1104
4 жыл бұрын
Can u suggest a cheaper alternative to the motors
@rashidhussain2060
Жыл бұрын
Hii bro Where did u get the android app . Is it available on play store.?
@TechAirHub
5 жыл бұрын
My fav part at 6:04 🤗🤗🤗
@fadayeh9b245
5 жыл бұрын
Who asked?
@trollfacesaccountifhegetst40
4 жыл бұрын
FADAYEH 9B who asked for you to reply?
@aliasgher6672
5 жыл бұрын
Wow nice
@Pagers270
5 жыл бұрын
Bro can you make this model with brushless motors for more speed. And please make a video on it. Please make as soon as possible because i want to make it for my project . if you cant make the video atleast tell us the changes to make in this project to use brushless motor. I hope that you will reply as soon as possible
@DIYBuilder
5 жыл бұрын
Yeah bro i am planning to make a super fast Arduino based car. So stay tuned :)
@Pagers270
5 жыл бұрын
@@DIYBuilder dude trust me i was thinking that you wont reply but you did. Hats off bro.
@Pagers270
5 жыл бұрын
Please keep the price of car under 4 thousand or 4500 please. Because most of us cant afford that much
@DIYBuilder
5 жыл бұрын
Bro i always try to give reply everyone's comment
@DIYBuilder
5 жыл бұрын
Ok bro and i'll use wifi module instead of a Bluetooth module to increase it's range
@vritikagm5199
4 жыл бұрын
you indian nice mujhe 1st price mila yaar thanks
@sunitatripathy3660
5 жыл бұрын
Bro did the same thing but not getting the pins in which you plugged bluetooth module. Can I us the male one to attach it
@akshadk7
4 жыл бұрын
Someone pls. reply asap
@dawad-ulopu7631
5 жыл бұрын
Its shows that the code is uploading but after few minutes shows that "an error occured while uploading the sketch" Please help
@DIYBuilder
5 жыл бұрын
Remove the bt module before uploading the code.
@praveenkumar8126
5 жыл бұрын
Bt module means sir?
@sefawinter
4 жыл бұрын
I had the same error. Then I pulled RXD and TXD cables from Hc-06. I uploaded code again. İt is okey. Then I loaded the Arduino Bluetooth RC Car app. İt worked. App match pin is 1234 .
@kholapnetnangrong219
4 жыл бұрын
yeah i made it anbd it work well but I cant make it move with 1.5V battery*4 and 9V so ijust powerback and connect with usb and it work well thank
@dfordulsath4441
3 жыл бұрын
Wow your videos are correct and amazing I made it and it worked
@sonalratnaparkhi4569
4 жыл бұрын
Awesome 🤩🤩
@keshobsaha3914
5 жыл бұрын
Nice car brother
@raoxter
4 жыл бұрын
Hi Bro ,Did the same as per circuit diagram,and Codes were uploaded without any error but when connected to bluetooth none of the motors are rotating ,Can clarify if wire for motors were done as per the serials on motor shield board.I guess for M1 and M2 the wireing was done front & back motors in combo
@navaneethkrishnannampoothi2317
3 жыл бұрын
Did it work ? We are facing the same problem
@pankaj9758
3 жыл бұрын
Interchange connection of Bluetooth module..Rx to TX.. mine was sorted out
@sreeharismulticraft2451
2 жыл бұрын
did it work ?? mine didnt
@zoller3822
3 жыл бұрын
Hi, what can happen if you did not put resistors in the bluetooth module? Tried it without it and it works. I'm guessing safety of the arduino?
@mridulagarg6790
9 ай бұрын
My car is not working idk why I have uploaded code everything fine but then also not working
@Parthaspartan1985
5 жыл бұрын
I have solved the frequent disconnection problem. Its nothing to do with the app,the bluetooth module is not getting enough current from the shield board.
@leireroma5161
5 жыл бұрын
How can we resolve it?
@Parthaspartan1985
5 жыл бұрын
@@leireroma5161 Hello... The bluetooth module is not getting enough current from the shield board. While experimenting, I just connected the 5V pin,Gnd pins direct to arduino output pins just direct below the shield,did not solder it. Add a powerbank to the main arduino board.Pull the jumper from the l293d shield.And the bluetooth stays connected for ever.
@leireroma5161
5 жыл бұрын
@@Parthaspartan1985 I've tried it but my car doesn't run, I don't understand why, but the bluethooth is connected.
@Parthaspartan1985
5 жыл бұрын
@@leireroma5161 hello... Can u connect the blth module with ur smartphone?? And what type of battery are u using??U have to 18650 or any high amp battery.Connect high amp power source to the L293d board and power bank with the arduino.Most importantly pull out the Jumper (Small yellow thing on the L293). Please describe the problem in details.. I will try to suggest u something...
@leireroma5161
5 жыл бұрын
@@Parthaspartan1985 Yes, the bluethooth module is connected to my phone. I'm using 18650 batteries (2), I have removed the jumper from the shield, but my car doesn't run. When I tried to run it makes a little sound (the motors, I think), but I don't understand why the car doesn't run. I have observed and I have seen that the supposed "green light" of my shield is not "on", don't know if it's normal. It's only that my car doesn't run, the bluethooth is ok.
@karangarg2085
5 жыл бұрын
Can you please tell how to make using l298n motor driver
@ashish835
5 жыл бұрын
kzitem.info/news/bejne/16-Q3Y2rf1-onGU👈
@FC_Prime
3 жыл бұрын
Do you used audrino compitable or development board?
@parekhrajesh
5 жыл бұрын
Can i use hm-10 bluetooth module for this project
@DIYBuilder
5 жыл бұрын
i am not sure but you can try
@parekhrajesh
5 жыл бұрын
I tryed but the app cannot detect the module and the connections are right
Пікірлер: 1,7 М.