If you're new and interested in learning more about laser cutting, here's my intro to laser cutting for beginners course where you can learn the basics of laser crafting: skl.sh/3HAydzm
@minravex9919
2 жыл бұрын
Ok
@minravex9919
2 жыл бұрын
Is it possible to layer design oval cube that. Might be up to 37 layers???
@LaserMadeProducts
2 жыл бұрын
@@minravex9919 not sure what you’re asking, but yes you can make a project with as many layers as you want to
@minravex9919
2 жыл бұрын
@@LaserMadeProducts thanks
@minravex9919
2 жыл бұрын
@@LaserMadeProducts I want a course on multi layers design for laser cutter...I can't fine it on skill share
@marekgodzisz5937
8 ай бұрын
Fanstastic job on this video and project! Thank you very much!
@LaserMadeProducts
8 ай бұрын
Thank you! Glad you liked the video and project
@turnswood
2 жыл бұрын
I love your work. Don't be afraid to go a little slower and share;-) I'd love to learn the process, but hard to learn at that speed. Thanks.
@LaserMadeProducts
2 жыл бұрын
Good point. I’ve been making slower paced and more in depth tutorials on skillshare skl.sh/3HAydzm
@johnharold1484
Жыл бұрын
You can go to settings at bottom of video(s) & select Playback Speed, pick the percentage you need.
@cornelljosephs9843
3 жыл бұрын
Your work is amazing, I would love to create things like these. Thank u for sharing
@LaserMadeProducts
3 жыл бұрын
Thanks so much 😊
@rachelkamath1866
3 жыл бұрын
Beautiful work! Thanks for sharing!
@LaserMadeProducts
3 жыл бұрын
Thanks for watching. Glad you liked it 😁
@LaserMadeProducts
3 жыл бұрын
Comment and let me know what I should make next! And if you're interested in getting a Glowforge for yourself, get up to $500 off of a Glowforge Pro with this link glowforge.us/r/VYSKLGWM
@asmcollection
2 жыл бұрын
Question - In Rhino whats the quickest way to extrude your layers with the cutout segments without clicking in every segment to trim?
@LaserMadeProducts
2 жыл бұрын
If I’m understanding the questions correctly, I would join all the lines for the overall perimeter shape and interior ones. Then select them all at the same time and extrude. It’ll automatically extrude the interior shapes as voids. Hope this helps!
@PosidenSiren
9 ай бұрын
It's georgous!
@LaserMadeProducts
9 ай бұрын
Thanks! I appreciate it.
@SD-eu7ht
Жыл бұрын
Brilliant. How do you stop glue from being squeezed out? Bravo!
@LaserMadeProducts
Жыл бұрын
Thank you! You just need to control the amount of glue you're using and keep it as centered between the perimeter of the pattern as possible
@avinashsurve2898
3 жыл бұрын
Thanks for your video definitely I try
@LaserMadeProducts
3 жыл бұрын
Good luck!
@phaleen
2 жыл бұрын
Thank you so much for this tutorial. I just purchased an xtool d1 10 w laser, should I change materials to ma5ch my laser capabilities? I have never worked with a laser before. I love your work! So esthetically pleasing.
@LaserMadeProducts
2 жыл бұрын
You’re welcome! I suggest practicing with your laser on small and simple projects. Once you have a good idea of how it works, you can switch materials and also adjust some design files to fit your needs.
@msliza814
3 жыл бұрын
I absolutely Love It, great job. Thanks for sharing
@LaserMadeProducts
3 жыл бұрын
Thank you for the feedback!
@macym57
3 жыл бұрын
@@LaserMadeProducts I love your work very much, it's very neat and beautiful 💕😊
@DecalVinyl
3 жыл бұрын
Excellent video!! Thank you 👊🏽
@5minprojects817
3 жыл бұрын
You just got a new sub ... your stuff is awesome. In the video you state you remove something off the wood. Are you putting masking tape down to save the edges from burning?
@LaserMadeProducts
3 жыл бұрын
Thank you! There’s usually a masking tape tightly pressed to the materials. It protects the surfaces from scorching, burns, and any debris during the laser cutting process.
@aic_under
9 ай бұрын
Beautiful Work, . do you know where can i get, vector files ready for laser cuting, like that geometric patterns?
@LaserMadeProducts
9 ай бұрын
Thank you! Lots of designers sell files on places like Etsy
@Hansieman100
Жыл бұрын
Hi Tim, wonderful artwork and even mote wonderful how you share it, clear, accessible and precise! Do you think one could combine this with epoxy to give it a stained glass look? Or are there difficulties in doing so?
@LaserMadeProducts
Жыл бұрын
Thank you and great question! I think you can combine it with epoxy within the open areas that you can see through to add color. The way I think it could work is you cut the first layer, pour epoxy into the openings, let it cure, sand and finish, then attach the remaining layers of wood. You could also cut 2x the layers so you have the depth on both sides of the finished piece.
@manuelvillalpando6665
2 жыл бұрын
What software are you using to create your pattern with? It looks a bit more complex than Adobe Illustrator or Corel Draw, which I am familiar with both of them to create my digital files for my K40 Laser Machine. Working with woods it's important to use some type of masking tape, preferably the clear Kraft masking tape, in order to reduce Flare Ups or Burn outs, and smoking up your wood products. If this happens, it is not a big problem, you just need to do some sanding and getting rid of the areas that have smoke blemishes. Every now and then you can pause your sanding too, and clean with 91% alcohol or acetone, let these dry completely off and inspect your work again. If you need to repeat the process, then all you need to do is follow the same steps as mentioned above. Woods can be a bit challenging with laser cutters/engravers. But again, if you ever experience burnouts, even with masking tape, just take a deep breath and get to sanding. How do you like your Glow Forge laser machine? Have you used others before too? If so, how do other brands compare to the Glow Forge? Thanks again for sharing the video and knowledge.
@LaserMadeProducts
2 жыл бұрын
Thanks for the suggestions and I agree. In terms of software, I use Rhinoceros. For laser cutting, I've been using my Glowforge for over 4 years now. I've used a few others as well. For hobby projects and size, Glowforge works well. If I ever decide to scale up and sell products, I'd transition to a stronger and faster laser like one of the Mira ones.
@christopherruizperez9586
3 жыл бұрын
What did you use to animate the design to make it look like wood before you actually cut it ?
@LaserMadeProducts
3 жыл бұрын
It’s a software called rhinoceros. I changed the material of the model to cherry wood and it applied it to the surfaces.
@davidbarlow1696
Ай бұрын
Some of the shapes seem to be slightly out of line. There is more of the layer below on one side.
@TheRanxerox
3 жыл бұрын
Once we purchase your files are we allowed to make and sell the product? Do you require attribution?
@LaserMadeProducts
3 жыл бұрын
Good question. You and make and sell as many products as you want! You just can’t give/resell the digital file. No need for attribution unless you want to attribute me 😆. Hope this answers your question!
@TheRanxerox
3 жыл бұрын
@@LaserMadeProducts awesome. Thanks. I always ask. Don't need any cease and desist letters. 😁
@torchwoodstudio1446
2 жыл бұрын
Amazing work, Tim! I've been laser engraving & cutting in my shop for a year now but just getting into the layered artwork recently. Your work has been a big inspiration. Do you happen to have a link to where you purchased the wood you were using in this video?
@LaserMadeProducts
2 жыл бұрын
Thank you! The wood is walnut plywood from Glowforge. You can get it in their online shop shop.glowforge.com/
@THEbaDrehtoMrEKCUF
4 ай бұрын
thanks!
@LaserMadeProducts
4 ай бұрын
You’re welcome!
@morsh_design
3 жыл бұрын
what is the name of software ?
@LaserMadeProducts
3 жыл бұрын
Rhinoceros
@peterrichardson7939
3 жыл бұрын
I’m new to your channel but you’re fricking amazing. If you’re not a millionaire for your work, you should be. I feel like you’re the type of person that would work in high fashion lol. Mainly referring to your lamps hit this was awesome too.
@LaserMadeProducts
3 жыл бұрын
Thanks Peter! I’m not a millionaire... yet! But with you’re support, I’ll be there some day 😆. There are lots of unique projects coming up, so make sure you stick around.
@minravex9919
2 жыл бұрын
Can I learn layers art design for laser cutter
@LaserMadeProducts
2 жыл бұрын
I’ll add this to my list of tutorials to make when I can free up some time 😁. Thanks for the suggestion!
@inc55
Жыл бұрын
What software did you use to creature the 3D model?
@LaserMadeProducts
Жыл бұрын
I use one called Rhinoceros, but a lot of CAD software these days that offer both 2D drafting and 3D modeling can probably do it as well!
@magusofthebargain
7 ай бұрын
Do more designs!
@LaserMadeProducts
7 ай бұрын
Lots of layered art pieces is in the works for my future projects and videos!
@SanchezStylez
Жыл бұрын
what programm u use?
@LaserMadeProducts
Жыл бұрын
It’s called Rhinoceros. But you can use any CAD software
@ekeneigwe7006
11 ай бұрын
How cab I get your files?
@LaserMadeProducts
11 ай бұрын
Hi there! You can get the file for this specific product here: etsy.me/2OLIpio and there’s a lot more in my Etsy shop
@prabhuram1876
3 жыл бұрын
Is it possible to purchase dxf file of this project
@LaserMadeProducts
3 жыл бұрын
The design file is available as an SVG here www.etsy.com/shop/UngStudioDesigns
@hearthfirefly6570
2 жыл бұрын
good video but the speed is an issue. Don't think I'd label this a 'how-to' if the examples are going so fast you can't learn anything.
@LaserMadeProducts
2 жыл бұрын
Thanks for the feedback!
@johnharold1484
Жыл бұрын
Drop the speed to 25% & pause at will.
@abedlalkhawaldeh580
Жыл бұрын
how can i start map engraving maker
@LaserMadeProducts
Жыл бұрын
Engraving a City Map with a Laser Cutter kzitem.info/news/bejne/x56Hqp6nr4OIhJg
@prabhuram1876
3 жыл бұрын
Material name sir?
@prabhuram1876
3 жыл бұрын
Name of the wood
@LaserMadeProducts
3 жыл бұрын
It’s Walnut plywood with a semi gloss finish.
@minravex9919
2 жыл бұрын
Can u do a paid design for me?
@LaserMadeProducts
2 жыл бұрын
Hey thanks for asking! I’m not taking on commissioned designs at this time. Good luck!!
@minravex9919
2 жыл бұрын
@@LaserMadeProducts what do mean
@minravex9919
2 жыл бұрын
@@LaserMadeProducts can u do step by step video tutorial
@mamay94
Жыл бұрын
How to Make Layered Geometric Mosqué Art
@LaserMadeProducts
Жыл бұрын
Oh that’s a great idea!
@gilbertboyer9936
10 ай бұрын
I found the title of your video somewhat misleading. It whizzed through the actual generating of the layer making and then showed the burning of the job. Very disappointed.
Пікірлер: 84