شكراً جزيلاً أستمر أكثر نحتاج منك فيديوهات أكثر بخصوص الآردوينو ومجال المشاريع الحديثة التي تخص الآردوينو وخاصة مشاريع خزانات المياه الذكية وتشغيل الموتور أوتوماتيكياً وقياس المنسوب وتكون بطريقة دقيقة وجيده مع شاشة القراءة الكريستال LCD وشكراً ❤️❤️❤️❤️❤️❤️❤️❤️❤️❤️
@KiyanisLab
Жыл бұрын
sure i will do that
@حيدرالغراوي-ق7ر
Жыл бұрын
@@KiyanisLab 🌷🌷🌷
@PavolFilek
Жыл бұрын
HOw many amps from morning to evening ? 30 - 40 A ? WHat temps at 30 AMSP are at FETs and caps and toroid ? Ripple at output p-p ? Do U have logging to uSD and WEB server or MQTT to show temps, current, voltages, efficiency ?
@ezeoluchukwu5104
Жыл бұрын
my great friend i see you
@GrahamBrown-hr7zc
5 ай бұрын
Hi Kiyani I have purchased your PCB and made your charge controller based on the schematic and sketch in your download MPT4.2 but no matter what I cannot make it work can you explain this part of the code ( //if(v) vi = (vo * 10) - vi;) and if if(v) should be remmed out. Is there a later version of your code? Also the pcb has a missing track A2 to U2 and the schematic shows the output going to A4 which I presume should be A2 have I got this right or have I made the situation worse? Regards Graham
@NoahHasenfang
9 ай бұрын
Could you use a smaller inductor if you increased the switching frequency? I know the arduino is limited in it's PWM frequency, but maybe an external IC could increase the frequency and reduce the cost/size?
@MaksymilianSkarbek-x7i
Жыл бұрын
hey I have a question if I could use this controller for a wind turbine and if the controller has overcharge protection the battery please reply
@quickfixengineeringltd8035
10 ай бұрын
Hi thanks. That 100uh inductor, can i use the smaller cheaper one
@BiomedicalEngineering-p9k
10 ай бұрын
Thanks for the graet project. Can I use this MPPT for 48V solar panel and 24V battery?
@giovannijaimes333
Жыл бұрын
Good job is posible input 250vdc to 24v?
@bokboxofknowledge3705
4 ай бұрын
Always done great job Sir can we increase amps range by increasing quantity of MOSFET.. thanks
@gep8639
Жыл бұрын
You r really good Engineer love from india
@ivanivanov-vo4vx
7 ай бұрын
Tell me, is it possible to install ESP1 Module as in version 4.1, if so, what needs to be changed in the firmware? Which ACS712 Sensor is used at 30A?
@MQVlogspk
6 ай бұрын
Sir no need mppt charge controller you can use any SMPS power supply as a mppt charge controller working very well
@salimanrafiu5982
2 ай бұрын
Really
@epinversores1294
5 ай бұрын
Your videos are very good, I'm a follower of your content, I'm a beginner in Arduino but I really want to learn and I'm researching a transfer key with synchronism, with your high knowledge you could make one for us
@sagarjana6037
Ай бұрын
Please give us the combine circuit diagram where we can easily draw a proper diagram in other design software at single layer pcb design. There are required any libraries function in programming? software.
@RdGear
7 ай бұрын
Bro, Please don't mind . Your gerber file and pCB , that use in your video is completely different .
@suataydemir9144
Жыл бұрын
Hello, there is a 20amp mppt charge control. Is it efficient to connect 4 50 watt panels in parallel or in series with 44 volts in 2 groups, the system is 12 volts?
@muhammedalliadedokun3823
Жыл бұрын
Can this be use for solar powered electric vehicle conversion?
@arnabroy5613
Жыл бұрын
Can you explain the circuit diagram and programming it is very helpful for every college student
@shailendersethi2619
2 ай бұрын
Can you make and supply one with details for 12 volt / 24 volt 200 AH bank. A multiple stage buck converter for using 3-4 panels in series for maximum efficiency and higher current for even a 12 volt battery. .
@Its-07
Жыл бұрын
Iam interested in electronic but bhai Kashmir ma offline electronic components nahi mil rahe koi online website batao please 👍❤️
@zahidmubeen8755
4 ай бұрын
good work if i want to in put voltage 160 then .......???
@muhammadasim3162
5 ай бұрын
Nice circuit explanation.Good Work .it's mppt or not .I have not seen your code
@nwaigbo3
8 ай бұрын
Great job Sir Please what's the toroid material and the inductance
@jboy4real
9 ай бұрын
What is the pwm frequency you are using. Thanks
@ezeoluchukwu5104
Жыл бұрын
Great engineer I suggest to add comment on most program line so that it can be well understood and it will create to u more fans based on the way u explain ur code.
@mobilesurgerybd
Жыл бұрын
Masha Allah
@Mani_sona
4 ай бұрын
sir in your diagram you show A4 current sensor insted of A2. A4 is already connected to SDA LCD Pin. kindly help us.
@Edmorbus
Жыл бұрын
Nice work what is the minimal input can i use this for 20v solar Thanks for sharing
@KiyanisLab
Жыл бұрын
Yes you can minimum 15v for 12v batt for 24v min is 30v
@Cookingstudiobyshahin
11 ай бұрын
synchronous or asynchronous buck converter use?
@Electronzap
Жыл бұрын
Very cool circuit.
@senthooransivagnanakumaran3855
Жыл бұрын
Sir, Can you please do a circuit that can handle 80A or if there is any way to convert this circuit to 80A because we have around 11 solars paralleled together so it would be a great help if the circuit can handle 80A. Thank you. God Bless You
@MegaRafa619
Жыл бұрын
😢Дайте информацию как наматать и какие кольца для индуктивности 110 uH???
@bengalmirror
Жыл бұрын
brother so this circuit/project suitable fir 12v & 24v battery?
@KiyanisLab
Жыл бұрын
yes
@childreneducationkk4592
Жыл бұрын
Can we add the Wi-Fi server in this PCB?
@duingstuff
Жыл бұрын
Very nice. What is the maximum solar panel wattage that this can take as input?
@DeltaLima274
Жыл бұрын
that is a simple math: Input Voltage * Input max Amperage = Input Max Power. So it is 80V * 40A = 3200W Then it depends on your battery, what your max Output power is. e.g. for an 12V Battery it would be 12V * 40A = 480W With an 48V Battery it is much more power. 48V * 40A = 1920W
@KiyanisLab
Жыл бұрын
1000 watts
@tubexcriolina
Жыл бұрын
Nice project. Can you please explain this part of arduino code : vo=((vo*0.06)/100); vi=(((vi)*0.6)/80); Where the 0.06 and 0.6 come from ? Does this code follow the any mppt algorithm diagram in particular? Does it follow the typical I-V curve for a solar panel ?
@CroftGaming1
9 ай бұрын
Those are voltage calculation from analog value, and sadly there is no MPPT algorithm, it's just a simple charger using a buck converter.
@MuhammadWaseem-qy2fd
Жыл бұрын
Hi sir schematic is not readabke in zip.can u update readabke circuit diagram
@Dc_tech386
10 ай бұрын
Your lcd display showing 15.2 v and input 88v but there is no way the voltage will say 15.2v with any load or to bleed down the 88 volt to 15 v so your not tell the full info I know this because I built negative buck converter and the voltage won’t turn down and Lest there is a load of 100 watt is on it to show that display
@jeffvenqueleir2036
Жыл бұрын
efficiency is about 93 percent maybe you should also show the efficiency on the screen but all in all a nice project
@KiyanisLab
Жыл бұрын
sure i will in the next version
@jeffvenqueleir2036
Жыл бұрын
@@KiyanisLab and maybe you can also make a digital volt and amp meter with an ads1015 or an ads1115 instead of analog this would be great I have seen in your code that it is only calculated to 20 amp is that correct?
@Ch-Shakeel
6 ай бұрын
Please make only meter solar volt and Ampere ,,, battery volt and wat on one display Like in this video
@Mani_sona
5 ай бұрын
Great project.
@sajidmohammad3190
Жыл бұрын
Make an oscilloscope within low budget.
@KiyanisLab
Жыл бұрын
ok bro soon
@EgKavak
Жыл бұрын
Can I charge a 12v 200ah acid battery ?
@septiyannungsizusizu8676
8 ай бұрын
I have tried this circuit but why is the output current very small?
@khalidshaffi
Жыл бұрын
Nice Project! The gerber file link is not working!
@mirjanaserali6439
Жыл бұрын
Nice support video
@ericsinkala3092
3 ай бұрын
Can we talk for a related project needed.
@joramotorsportteam3277
5 ай бұрын
Where is next video? 80 to 5 Volts DC to DC only??? We will learning about MPPT!!!
@_AqibSaeed
Жыл бұрын
SIR WHEN I DRAW THIS PROJECT ON PROTEOUS SOFTWARE IT SHOW D2 D3 D4 D5 D6 D7 EROR. BECAUSE YOU DID NOT DEFINE THESE IN YOUR DIAGRAM SO PLZ EXPLAIN
@KiyanisLab
Жыл бұрын
is d2 d3 d4 diodes in you diagram if so choose ones with simulation model
@qadeer1685
Жыл бұрын
Good 💯
@BiomedicalEngineering-p9k
10 ай бұрын
What is the purpose of the potentiometer?
@thanhbinhnguyen6069
Жыл бұрын
can you make it work with 48v battery. Thanks.
@KiyanisLab
Жыл бұрын
soon bro
@untungsuharto7991
Жыл бұрын
where I can buy this mppt?
@bengalmirror
Жыл бұрын
Great
@engineerkohat
7 ай бұрын
Hi dear zain.
@tvbox8478
Жыл бұрын
👍
@Ch-Shakeel
8 ай бұрын
I want to buy this
@CroftGaming1
9 ай бұрын
It is not an mppt, its just a buck converter
@oshinijagoda3062
Жыл бұрын
I made it your pcb but it didnt work .lcd display isnt work
@muhammadnoumanhanif1
Жыл бұрын
Will it support Wi-Fi Server?
@KiyanisLab
Жыл бұрын
no upcoming version will be
@muhammadnoumanhanif1
Жыл бұрын
@@KiyanisLab When will the next version be coming? Can I add the Wi-Fi sever with the help of your previous video?
@bengalmirror
Жыл бұрын
waiting for 36V,48V,60V,72V project
@KiyanisLab
Жыл бұрын
soon
@tonyh6309
Жыл бұрын
Fake. At least the circuit diagram is. There's no way that 4 Mosfets with 7nF input capacitance and a gate voltage plateau of nearly 5V can be driven with a 47K/10K ohm divider from 28.8V (ie. 5.05V gate drive) switched by an optocoupler @ 31.4kHz! It couldn't even drive the one Mosfet that is all that is needed given that at 40A, 12V ouput, conduction losses would be < .5%. Maybe it could work at a few hundred Hz, but then the inductor would have to be enourmous! Reducing the resistor values drastically wouldn't help - 3.76K/2K could at least switch a single FET but the switching speed would still be so slow that the switching losses would be 100s of Watts! The silly thing about this design is that all it would take would be 2 or 3 dirt cheap bipolar transistors as a Mosfet driver to make it work (if not especially efficiently) if you really can't afford a proper driver chip. But cost doesn't seem to be an issue when he links to the 100uH main inductor costing $45 + $25 shipping!!!! A sensible design would use a much higher switching frequency, say, for example, 200kHz using an SER2915H-472 5.6uH, 0.67mOhms inductor costing $3.39 for one off direct from Coilcraft. The Arduino Nano can create a 200khz PWM, but with a reduced resolution of 1:80 rather than the 1:255 (8 bit) default. However if you did modify this design so it can actually work, if you run it at 56V input, 24V/40A output, the input capacitors would likely explode as their ripple current rating (probably 2 to 3Arms max for each capacitor) would be far exceeded by the 20A total ripple current they would be actually called on to deliver...
@股天乐-t2c
Жыл бұрын
Hope you can improve on the question asked and make it work better, thanks.
@MegaRafa619
Жыл бұрын
this deceitful author doesn’t even give how he made 110uH.... Do you know how to make the correct inductance in this circuit? I have already ordered the boards.... and all the components, spent the money.... Help, give information about inductance??)))
Пікірлер: 90