ive been machining 20years plus. ive never seen splines cut with a grinder. with his tools and equipment this is amazing
@keepsgoing4evr1
3 жыл бұрын
That's pretty cool that you're using some of the parts you already restored on your other channel! 🧔👍💯
@billhicksmcgee1181
3 жыл бұрын
Some wicked cutting tools on that lathe haha
@shawngoldsberry747
3 жыл бұрын
The tool post on the lathe is a beast, looks crashworthy.
@wpowerwagon
3 жыл бұрын
Nice and great job, thanks for sharing your thoughts and great videos
@amphibianmotors2918
2 жыл бұрын
If you want to make a Dana 50 heavy duty dead center front diff modify an old Ford 4x4 Twin Traction Beam Differential. The old Ford Front differentials from a twin Traction beam suspensions used from 1983 to 1997. I used a Dana 50 TTB dead center on the front end in the car in the video. The main thing I had to do to locate it dead center between the front tires was make a speedy sleeve for the drivers side seal location. The speedy sleeve allowed the drivers side to accept a bearing, a seal and a yoke similar to the passengers side. The spline on the Dana 50 TTB and the Dana 44 TTB differentials inner yoke stubs are both 30 splines 1.29" OD. On the front end I am running I was initially running Cardan type U-Joints against the ford TTB differential and Chevy 4x4 1500 CVs at the outer front hubs. It worked for the prototype but I got a slight vibration. It is typically NOT a good idea to mix cardan U-joints mixed with the CV joints they typically do not work well together at an angle. I was going back and making custom inner stubs for the front Dana 50 that I can match up to Porche 930 CVs. Also note that works but the CVs need to be rotated clocked correctly so the boot on the Chevy CV has to get pulled back to see how it is oriented. kzitem.info/news/bejne/zoeFnHqbcZmoiqw
@chadliggett286
2 жыл бұрын
Do you have a video on that Porsche half shafts conversion!
@bertsandlin4850
2 жыл бұрын
@@chadliggett286 Still running the OEM cardan joints against the diff and Chev 1500 4x4 outer steer CV joints against the hubs. Wasn't planning on making a video. I was hoping somebody would chime in at some other sites and let me know if there were existing OEM stubs out there that could be used. I can cut the exiting stubs and do some welding to put some metal that I can machine down on the lathe but if something is out there that is a lot less work.
@jamesshamley6577
3 жыл бұрын
This guy is a good engineer.
@scoc253
3 жыл бұрын
_very good! very clever! only complaint is that the bearing was not packed with grease._
@khimsophacarfixing
3 жыл бұрын
That is a good idea!
@shawngoldsberry747
3 жыл бұрын
Your methods seem strange to me, but I cannot knock them because your results very impressive
@brunogeraldo7210
4 жыл бұрын
Congrats for your incredible job with all... Good luck and be successful in your life. Brazil 🇧🇷 2020
@IbrahemAlbanawi
3 жыл бұрын
awesome video a fan from Saudiarabia 🇸🇦
@timwegman5776
3 жыл бұрын
Awesome man
@Maubere-reac
2 жыл бұрын
Really awesome ❤️
@hitmn2011
3 жыл бұрын
Really very beautiful my friend deserves all thanks and appreciation for this effort Greetings to you keep in touch
@Youtubeforcedmetochangemyname
3 жыл бұрын
Nicely done
@dtv5862
4 жыл бұрын
Good luck bro
@willwade1101
3 жыл бұрын
The only thing I would change would be to put flanges on the output shafts to make changing a broken shaft easier.
@gabrielcatani9317
3 жыл бұрын
Excelente, para un Bugi va como trompada.
@ROVITTv
3 жыл бұрын
Cool
@hectorcasas2113
3 жыл бұрын
nice Job
@gloomgloomy9147
3 жыл бұрын
Very helpfull
@kreasiumum
3 жыл бұрын
thanks for the your video
@reverserestorations26
3 жыл бұрын
I like the part where he cut a decent set of splines with an angle grinder.
@witosarlaw
3 жыл бұрын
mantap bang
@aashishtale3917
4 жыл бұрын
Add some car restoration video
@gmillions1
2 жыл бұрын
3:41 unreal grinder work! Definitely has some skill!
@juizzii386
2 жыл бұрын
Skill???
@alejandrodelrio960
3 жыл бұрын
exelent tips
@coburnlowman
3 жыл бұрын
Why is nowhere in the description or answered anywhere of what kinda differential this is? I'd like to build 4x4 side sides for farm use but haven't found a good diff to use , or cheap and readily available.
@pink_love_cat4928
3 жыл бұрын
Was that just made out if all water pipe fittings ? if so !!! WOW !!! THATS SOME SERIOUS THINKING GOING ON
@5phutsangtao-iQ
3 жыл бұрын
I also want something like that
@benjaminaiwusiaikins5829
3 жыл бұрын
What type of differential is this and how to get it. Thanks
@chudin4767
3 жыл бұрын
That axle is as strong as that weld on that jacked up shaft that was welded. Wooooow. Lol
@RG-gk4yi
3 жыл бұрын
That might have been just to hold it while he cut the splines.
@timwegman5776
3 жыл бұрын
@@RG-gk4yi correct it was just to hold it so he could get accurate cuts, I also thought this was odd at first until I realized what he was doing. He wouldn't need nor want a strong weld here as you clearly see a few min later that the parts were separated.
@luislopez7890
2 жыл бұрын
Question is does it work and hold up..... ?
@ruslankotleta4000
3 жыл бұрын
from which machine the reducer?
@-Je2021
3 жыл бұрын
meus parabéns muito sucesso sou mais um inscrito estamos juntos um ajudando o outro que Deus abençoe
@asgharpti9380
Жыл бұрын
I need this one
@mihirinisansala8484
4 жыл бұрын
Bro sand blasting karne koheda???
@ciobanuvalentinmail
3 жыл бұрын
Super
@ivancruzluque2795
3 жыл бұрын
En las uniones es mejor avellanar los extremos para q la soldadura sea solida
@choudharysureshbhanuda
3 жыл бұрын
Naic paraj Kiya he indi
@PNWLeviathanFPV
3 жыл бұрын
Man you made me nervous with the chuck to the angle of the tool holder.
@Edbod
3 жыл бұрын
what kind of diff did you start off with
@Youtubeforcedmetochangemyname
3 жыл бұрын
That's my question too
@ezequielsilva2709
4 жыл бұрын
Muito bom!👍
@joshuahalla.k.a.controlla6333
2 жыл бұрын
Wow.
@sebastiaosilva9471
3 жыл бұрын
Esse diferencial é de que veiculo?
@fabioalves7763
Жыл бұрын
De qual carro é esse diferencial?
@yung1388
2 жыл бұрын
,👍👍👍👍👍
@chuchin19cmgonzalez41
2 жыл бұрын
Una pregunta ese eje de diferencia de que carro es perdón mi ignorancia
@blacksantozz9135
4 жыл бұрын
Bro can you make a chain drive differiential
@mariotaylor9990
3 жыл бұрын
It’s not hard mount the engine sideways and put a sprocket on the drive shaft easy awd to
@ApocGuy
2 жыл бұрын
@@mariotaylor9990 goes the same for car's engine. just use both half shafts as outputs for front and rear diff/axle ;)
@hankhill5860
3 жыл бұрын
Could have just shorten the axle tubes and existing axles then use the GM CV axle with the flange set up,
@timwegman5776
3 жыл бұрын
He would of still had to deal with sealing it right, as soon as he cut into it he would have to seal it up one way or another. I don't see why so many people are being negative with this I think it was a very creative solution to get independent suspension and in many countries like his I assume they don't have the access to parts that say people in America do so they have to make due with what they have and come up with creative solutions as he has. I think it was very informative and neat to watch thank you for sharing.
lot easier to take one from an s 10 or Subaru pretty much the same
@ignasiusporus9111
2 жыл бұрын
Bisa krm tu sy ko
@mihkus
3 жыл бұрын
Solid steering front axle would have been million times cooler than a differential ONLY...
@sebastiaosilva9471
3 жыл бұрын
Oi bom dia...
@stevendunn405
3 жыл бұрын
How much would you charge to build me one sir. Can pay cash app/paypale??? Im serious about this inquiry.
@GutZ_47
3 жыл бұрын
HEY BUD, ANYWAY YOU COULD TELL ME WHAT THAT AXLE CAME OUT OF?
@adrianasubianto5468
3 жыл бұрын
Cek harga kardanya bos
@user-ym3rg2lo6p
3 жыл бұрын
От чего мост использовали?
@user-jl1ds2ok7d
3 жыл бұрын
А для чего
@71rus.54
3 жыл бұрын
Интересно с чего мост?
@user-jl1ds2ok7d
3 жыл бұрын
Не с чего а для чего эта хрень
@user-wi8fr9ps7h
3 жыл бұрын
Это для минитрактора
@user-wi8fr9ps7h
3 жыл бұрын
Вот с чего мост это точно известно
@blairbreland1443
3 жыл бұрын
Hope they don't use any more than 10 hp on it
@thestreets5206
3 жыл бұрын
Shocking welding 😔
@idowonder4926
3 жыл бұрын
Hello from Russia! Please tell me, which car is the gearbox from?
@Mihey387
3 жыл бұрын
На алике подобный есть. Не дает ссылку вставить. Закинул бы.
@interestinginnovations619
3 жыл бұрын
Which vehicle differential is this?
@asgharpti9380
Жыл бұрын
Please send me in 🇦🇪 uae how much money
@yopyop3933
3 жыл бұрын
So there's no DANA in India ????😎😎
@user-on3lf4dp6y
3 жыл бұрын
Shaizen
@Hamdolla
Жыл бұрын
سلام خداقوت لطفاکلیپ بازیرنویس انگلیسی تهیه کنیدکه قابل فهم وقابل فورواردباشد. دیفرانسیل به هواکش نیازداردیاندارد؟
@asgharpti9380
Жыл бұрын
Where i get
@tronixfix
3 жыл бұрын
N where's the buggy?
@user-pf4ix2cc3t
3 жыл бұрын
Ассаламалейкум
@user-ow6eu1dj1v
3 жыл бұрын
Солим по маленьку.
@Questionable_creations
3 жыл бұрын
That axle was perfect for a go cart, untill you ruined it.
@Reedic20
3 жыл бұрын
Somebody need to learn how to weld
@leatherandsilver350
3 жыл бұрын
Хоть бы сначала научились понимать, что такое механические узлы и что для чего служит и как работает........ ТАкое чувство что главное заливать видосы на просмотры, но похрен как и что там делается.....
@hedozonez
3 жыл бұрын
what car is this differential from?
@greasysteve5671
3 жыл бұрын
Looks like an old golf car diff
@asgharpti9380
Жыл бұрын
Please send me in parcel tcs
@Carlos-vf7jy
2 жыл бұрын
Todo esse trabalho só pra isso 😫
@user-wi8fr9ps7h
3 жыл бұрын
Мост с чего
@user-ke1jc5ty3z
3 жыл бұрын
💪👍👍👍
@user-jl1pz5kn8r
3 жыл бұрын
Это что такое? Для чего?
@user-ke1jc5ty3z
3 жыл бұрын
Редуктор заднего моста
@user-xv5yv6jz1r
3 жыл бұрын
Был задний мост ,стал передний, вместо полуосей установили шруза ,лайк!
@user-jl1ds2ok7d
3 жыл бұрын
У меня кот тоже яица лижит
@startofthehunt2997
3 жыл бұрын
И зачем это делать???
@user-pk7bb5yg1i
3 жыл бұрын
На самодельный квадроцикл
@charliemclaughlin1042
3 жыл бұрын
Good luck with that lasting more than a day lol😂
@student1979oct
3 жыл бұрын
I was kinda thinking the same at first, but I've seen some crazy shit last far longer than it had any right to, so who knows??? :D
@rickbiddle2931
3 жыл бұрын
what the hell is that thing going to go on
@timwegman5776
3 жыл бұрын
No you all are wrong! You have no bases to believe this would brake in a day, the weak point being the new splines and he cut rather deep and think splines so while possibly not as strong as originally I have confidence it will NOT fail in a day!
@egormyasoedov6905
3 жыл бұрын
Просто бред
@madslinsanity3877
3 жыл бұрын
Oyawa contact karaganna number eka danna
@user-sz5mz9em1f
2 жыл бұрын
Я хочу общаться с вами через
@user-jv5uo8cz4l
3 жыл бұрын
Ох и загудит эта вся хуита. На шарико-подшипниках)))
Пікірлер: 123