Excelent video Could it be done with more channels, or should there only be 6 channels for the circuit?
@techideas6772
Ай бұрын
Yes, of course.
@bijumathew8758
4 жыл бұрын
Very good and very nice
@buddhimann
6 ай бұрын
Request you to make car scanning welcome light with DRL
@m1n1truck3r2
4 жыл бұрын
I really like it! :) But I can't quite make up what the diode is for. Is this infinitely expandable? Also, is it possible to make the LEDs turn off al at the same time, instead of them fading out?
@techideas6772
4 жыл бұрын
If all leds turn off after running it would be called led chaser. I've a video on led chaser. kzitem.info/news/bejne/zrCuy2R-moFyi4Y If you don't use diode the leds will not flow and may be only first led run. Diode is used to complete cycle of leds.
4 жыл бұрын
Excellent project friend. Is this for use with 9v input? or to use it with 9v should I change any resistance and capacitor?
@techideas6772
4 жыл бұрын
Yes it can work on 9v to 15v. I used 12v for this project.
@ignaciomatias4900
5 жыл бұрын
Excelente! Quiero saber hasta cuantos leds se pueden colocar para hacer este circuito. Gracias.
@techideas6772
5 жыл бұрын
I can't understand your language.
@techideas6772
5 жыл бұрын
Maximum 3 leds in series or parallel.
@just1lifexx11
3 жыл бұрын
Nice
@SuryaPrakashMedhi
2 жыл бұрын
Hi, I wanted to set this up for the LED strips in my stairs. I want each step to light up on after another. Can I connect an LED strip instead of each LED bulb that you have connected in this model? and How do I slow down the speed of lighting?
@techideas6772
2 жыл бұрын
No it can't work as staircase lighting.
@rockimmi83
5 жыл бұрын
amazing bro..looks cool...but can you explain that which capasitors to use to lower the speed??
@techideas6772
4 жыл бұрын
Capacitor also depends on the speed of flow but discharging resistor (that I used 680R in the video) depends more for led flow. If you use more than 3 leds in series or parallel with one transistor then you need to install bigger capacitor.Just change the 680R resistor to 1k or 2k variable resistor & set speed to your own choice.
@rockimmi83
4 жыл бұрын
@@techideas6772 thanks bro
@luimonarch
2 жыл бұрын
What kind of capacitor would make the LEDS turn on slower?
@techideas6772
2 жыл бұрын
Bigger value capacitors.
@VadeniucROKasCoTV
3 жыл бұрын
If i want led run faster, what i need to change?
@techideas6772
3 жыл бұрын
Capacitor and 680R resistor
@1silvervespa
2 жыл бұрын
Paint the circuit board first then fit things .
@shawonkhan8083
2 жыл бұрын
Can I use a potentiometer to control the flow
@techideas6772
2 жыл бұрын
Yes you can use 1k potentiometer where I used 680 ohm resistor.
@tinhtutaung1206
3 жыл бұрын
Hello bro I want to do like this but I want to use 16 led for one side. So what I need to change and how to make can you give me advice. PLEASE
@techideas6772
3 жыл бұрын
Use 3 leds in parallel. You can use 15 or 18 leds for 5 or 6 channel.
@tinhtutaung1206
3 жыл бұрын
Thank you so much alot bro.🥰🥰
@tinhtutaung1206
3 жыл бұрын
@@techideas6772 each 1 channel I will you 3 led and Capacitor , resistors are need to change or not? Bro please....
@techideas6772
3 жыл бұрын
@@tinhtutaung1206 Only increase leds other circuit remains same.
@tinhtutaung1206
3 жыл бұрын
@@techideas6772 Oh! Thank you again bro
@melvinverkerk5601
4 жыл бұрын
Can you make it work for 24v input?
@techideas6772
4 жыл бұрын
I not tried yet but it can better work on 24v by changing resistors & capacitors.
@zergenokcs2
4 жыл бұрын
hi, can i use more leds?
@techideas6772
4 жыл бұрын
You can't use more than 5 or 6 segments but you can use leds in parallel to increase length.
@asseressam8252
Жыл бұрын
@@techideas6772 why i cant use more than 6 segments ??
@techideas6772
Жыл бұрын
Because led flow will not be proper.
@asseressam8252
Жыл бұрын
I used 6 transistors and connected 2 last leds together but they are not bright as the rest why ?
@techideas6772
Жыл бұрын
@@asseressam8252 Only use lower resistor value for the led.
@hootistigglebits
3 жыл бұрын
Did you not use a 555 timer?
@techideas6772
3 жыл бұрын
No it will work with the bike indicator flasher.
@nguyenbao9349
3 жыл бұрын
Hello! in this circuit can i use 12v led?
@techideas6772
3 жыл бұрын
No, if you want to run 12v LEDs you should have to use switching transistors.
Capacitor is used for the flow of LEDs, bigger the capacitor value flow will be slow. 220R is used to protect LEDs for over current, you can use 330R and 10k for transistors. For 680R or 1k resistors you have to set the value of resistor to own to discharge the capacitor in such way that LEDs flow sequence is good.
@anwarzaidan9851
3 жыл бұрын
@@techideas6772 I ask for advice from you, these are the components I have (10k resistors, 330ohm resistors, 2k2 resistors, 100uf 16v capacitors, and 1N4007+bc547 diodes, which components should I replace to make it safe for the vehicle,,, what should be according to what you make in the video, please answer...??
@techideas6772
3 жыл бұрын
Yes this can work but you have to change values a little bit for decent flow.
@anwarzaidan9851
3 жыл бұрын
@@techideas6772 ok, which is the little value that I have to change, is it a resistor, or a capacitor, or something else, please answer again..?
@miguelmattioli5148
4 жыл бұрын
Bro I need help, I want to make a normal turning signal, I have to power it up with 6 volts and I want to put 4 LEDs in parallel, what resistor do I need? Plis thanks for help
@techideas6772
4 жыл бұрын
You need to use same schematic but lower the values of resistors to change speed of flow and discharging capacitor. And set according to your need where it works fine.
@miguelmattioli5148
4 жыл бұрын
I want to know the value of the resistor I need for just 4 orange LEDs in parallel with 6v
@techideas6772
4 жыл бұрын
@@miguelmattioli5148 I have to make one for 6v so you have to wait. I'll upload video or reply you.
@miguelmattioli5148
4 жыл бұрын
@@techideas6772 thank you bro
@techideas6772
4 жыл бұрын
Do you need 5 segments with 4 leds in parallel or only 4 segments with one led?
@giuseppelodrago2362
4 жыл бұрын
where is the diagram?
@techideas6772
4 жыл бұрын
At 4:35
@giuseppelodrago2362
4 жыл бұрын
@@techideas6772 thanks ❤️
@kish240
3 жыл бұрын
Can you share the schematic?
@techideas6772
3 жыл бұрын
Schematic diagram is in the video
@randominventions3005
3 жыл бұрын
Would 2n2222 work instead?
@techideas6772
3 жыл бұрын
Yes but pin configuration may be changed.
@randominventions3005
3 жыл бұрын
@@techideas6772 so it wouldn’t work if I just swapped the bc547’s for 2n2222’s?
@techideas6772
3 жыл бұрын
Check pinout first if they are same then use.
@techideas6772
3 жыл бұрын
@@randominventions3005 You need to change the face of transistor to other side so pins will be as bc547.
@randominventions3005
3 жыл бұрын
@@techideas6772 so just turn it 180 degrees
@henkywardana4524
4 жыл бұрын
Hi.. can i use 1w 3v led? Hpl led
@techideas6772
4 жыл бұрын
Yes! You can.
@henkywardana4524
4 жыл бұрын
Thank u. how to change led speed?
@techideas6772
4 жыл бұрын
@@henkywardana4524 Change the resistor that I used 680R in the video.
@henkywardana4524
4 жыл бұрын
Thank u.. i using 1w 3v led (6pcs). It can lighting like yours. But for led number 5 and 6 from left was blinking. What is problem?
@techideas6772
4 жыл бұрын
@@henkywardana4524 I didn't understand what you mean?
@manumohan195
4 жыл бұрын
Can i get circuit diagram
@techideas6772
4 жыл бұрын
@ 4:35
@venkateshbhat9890
4 жыл бұрын
Bro need your urgent help which capacitor which resistors and which transistors should I use if I want to make 6 segments of 3 1watt leds in each segment parallel connection of leds? I hope you will reply soon
@venkateshbhat9890
4 жыл бұрын
Bro please reply.
@techideas6772
4 жыл бұрын
Replace 680R resistor with 5k variable and 200R to 300R for leds.
@venkateshbhat9890
4 жыл бұрын
@@techideas6772 thanks a lot bro appreciate your efforts to help me just one more question if I use 5k variable on what ohm should I set it.
@techideas6772
4 жыл бұрын
@@venkateshbhat9890 5k variable is used for flow speed. Higher the resistor lower will be speed. Set according to your choice where it works good.
@venkateshbhat9890
4 жыл бұрын
@@techideas6772 thanks a lot bro appreciate your efforts a lot ❤️
Пікірлер: 97