Very cool. I'd add a drain valve at the bottom to drain the water.
@omsingharjit
3 жыл бұрын
Or use silica gel at intake
@aerialrescuesolutions3277
3 жыл бұрын
Great work there, how many people could figure that out with all the tools and resources available herein the US? Very few. It's easier to go buy something. However, when you have very little to play with and still manage to design, build and use an item like this from scraps, Bravo...... This fellow is a very smart and resourceful person. I would hire him in a second. Very well done my good man, well done. Jim
@steptoeandson3554
3 жыл бұрын
When he works for you ensure he wears safety shoes
@ogreunderbridge5204
3 жыл бұрын
In a similar project I ran into a problem with weldable tube fittings and ended up with having to do a gas brass brazing. It seems all fittings I can get is either brass, stainless steel or copper. Wich typical places sell normal tube fittings in normal steel, AN threads aside?
@victorioungasis7994
2 жыл бұрын
Is there a need for oil on the compressor........if there is how much do i put on the compressor
@gouravchatterjee2060
3 жыл бұрын
Sir pura set kaha mile ga
@jeansinesio4900
3 жыл бұрын
Excellent!
@valtersouzaribeiroribeiro9534
3 жыл бұрын
Nice good
@omsingharjit
3 жыл бұрын
How much air can be compressed in 15 kg lpg cylinder ? More or less or equal ?
@29mbalam
2 жыл бұрын
please make a low pressure automatic compressor for airbrush.
@sooriyajeyasooriyan7094
2 жыл бұрын
Hello brother Good work And how much on compressed capacity? *how much time to need on fully on 25l cilinder?? Please replay. Thank you.
@jamesferrer8761
3 жыл бұрын
What are the materilas needed, pls.
@hanselfita9188
3 жыл бұрын
Sir how to set the automatic pressure switch to that kind of switch
@luismedina8915
3 жыл бұрын
Disculpa el tanque solo se llena con pura agua
@awaragard5593
3 жыл бұрын
If I wanna purchase from you how much it costs
@barruanimalstories2268
3 жыл бұрын
Yg nulat itu di atas apa tu bang
@gwlilly5786
3 жыл бұрын
Where is your drain ?
@aerialrescuesolutions3277
3 жыл бұрын
No drain in India, just works fine.
@thaimeup5545
3 жыл бұрын
@@aerialrescuesolutions3277 ....Zero condensation. That type of compressor can't last more than 5 min without oil vaporized in the gas. As is the case with refrigerant in a closed system.
@aerialrescuesolutions3277
3 жыл бұрын
@@thaimeup5545 It needs a drain for sure, but, when you got nothing , it works all right.
@thaimeup5545
3 жыл бұрын
@Christian The compressor that was used is typical for a residential refrigeration unit. It is hermetically sealed. The motor and compressor cannot be accessed. All lines to and from the compressor are in a closed loop Oil is vaporized in the refrigerant and lubricates all moving parts. This is not like a standard air compressor, which has air being compressed from one area and forced out in another area. Air compressors do not recirculate the same air. Therefore, they typically use a crankcase to store oil for lubrication
@nomercadies
3 жыл бұрын
Too many unprotected fittings to knock off and cause accident.
@gouravchatterjee2060
3 жыл бұрын
Cilynder+ compressor hai
@fun2dostudio972
2 жыл бұрын
Best car compressor: kzitem.info/news/bejne/uaSws4yLjmOEYKg
@siddhantmittal2245
3 жыл бұрын
its very slow
@jozsefmihalyi2818
2 жыл бұрын
full idiot. Grat. :(
@Valenciarony
2 жыл бұрын
Compression fittings don’t need Teflon tape specially when the metal is copper
Пікірлер: 29