If you want text version of any of my Projects visit 👇👇 www.newphysicist.com 🔥 There You can read my experiences while I’m making that particular Project. Thank you. Happy Making.
@premsingh-tj5eo
6 жыл бұрын
I have only been using solar water heater (different design) heated water For more than 8 years now for bathing etc... 🙌🙌🙌 Little proud moment 💪💪😳
@navneetkalra8067
5 жыл бұрын
prem singh pls share a photo
@frankenstein3163
5 жыл бұрын
Did you make the spiral coil. And did you use a thermal storage container like a ice chest ?
@TheOleHermit
5 жыл бұрын
Nice job. Enjoyed the video. Several years ago, I had a similar design. But, I used a reflective metal sheet, which eliminates the step of applying mylar film. Also used bearings around the pipe, mounted on the end panels. So, the reflector pivoted around the stationary water pipe (angled towards the south, at the # degrees from the Equator). Then, with the reflector balanced around the pivot point, a small DC motor (controlled with 2 photo resistors and an Arduino NANO) can be used to track the sun. This solar tracking assembly can be built for less than $50. Also, a standard thermostat valve from a car engine can be used at the hot water output to optimize the water flow through the parabolic reflector, so a small dc pump (with automatic pressure shutoff and expansion tank) can be used at the cold water input to 'feed' the solar heater. A system such as this is ideal for hot water tanks and in-floor radiant heating.😎
@uwulaanbar9176
2 жыл бұрын
Can you give me the reflective angle pls
@TheOleHermit
2 жыл бұрын
@@uwulaanbar9176 There is no set angle, because the sun changes its vertical angle from summer to winter and the horizontal angle changes from morning to sunset. The parabolic mirror tracks the sun horizontally throughout the day, reflecting the sunlight onto the water/fluid pipe, like a reflective lens focused on the pipe, opposite side from the sun. The pipe is best set at 90 degrees to the angle of your local midday sun at winter to optimize it under the worst scenario.
@donsuji1658
Жыл бұрын
@@TheOleHermit what was the total fabrication cost of your design?
@TheOleHermit
Жыл бұрын
@@donsuji1658 Thank you for your interest. However, life happened, so I never had the opportunity to build the monolithic dome home to complete the project and didn't do a cost analysis. But, I believe in its feasibility, because of it's simplicity. The solar tracker circuits are available on Amazon: www.amazon.com/Solar-Tech-Power-Analog-Tracker/dp/B00F74H9SA/ref=sr_1_13?crid=2E3KE3LESLFGU&keywords=solar+tracker+controller&qid=1666191442&qu=eyJxc2MiOiI0LjE2IiwicXNhIjoiMy4zOCIsInFzcCI6IjAuOTIifQ%3D%3D&s=lawn-garden&sprefix=solar+tracker%2Clawngarden%2C146&sr=1-13 The rest depends upon the specific design of the system. The radiant heating and water heater costs are the same as conventional designs. BR 😎
@johnverkler3962
Жыл бұрын
Mr. The Hermit...They're looking for simplicity here. Everybody can't get the things, knowledge, electronics, programming, wiring, you require. No harm intended. Just saying.
@newphysicist
6 жыл бұрын
Solar power is endless. Start tapping its unlimited potential.. If you enjoyed this video CLICK the LIKE button, Otherwise KICK and KILL the LIKE button..😁👌👍😉
@yonkromis7883
6 жыл бұрын
How many gallons or liters per minute can you get out at 100 degrees C or at shower temperature and if you made it a lot longer you could get a lot more right I also saw where you can point it east and west where you don't have to track it to follow the Sun constantly you can just change it every few days or so but when it's pointed along the track of the sign you don't have to have it track the Sun good job keep up the good work I've got a lot of thoughts along these lines like preheating the water Etc minute by minute
@yonkromis7883
6 жыл бұрын
You might paint the pipe black and put another reflector above the pipe about is big as a beer can cut just to catch the extra light bouncing off
@timothybeebe6382
6 жыл бұрын
New Physicist just curious would glass over the top increase temperature? Awesome build by the way👍🏻
@trishy5626
6 жыл бұрын
Solar is hard to get for 93 days in cloud covered Cass county Michigan. Many of us are vitamin d deprived in this area so my Dr told me. Wish I could do this it looks amazing.
@freddyfourfingerz9126
6 жыл бұрын
New Physicist, would adding a glass top over the parabolic device increase maximum temperature of the pipe?
@downunderdan5132
6 жыл бұрын
My brother, this is fantastic! I want to try a portable version for camping. Thank you very much for sharing your experience 😊😎😊😎 🇦🇺🇦🇺
@obakhanjones2869
6 жыл бұрын
I love how you make these projects simple and easy to grasp
@hyqhyp
6 жыл бұрын
Only the tiny qty of water in the pipe will get heated, the rest will not because there is basically no convection path for the hot water. As soon as that runs out you will get cold water. I would remove the tap and take the heated water back into reservoir, and put the tap on the reservoir. As a bonus insulate the reservoir (say inside lots of coconut fiber or styrofoam), and you'll have hot water even when the sun temporarily disappears, or in the evening.
@randypratt2887
7 ай бұрын
But with such a small amount flowing through the heated pipe it will bee heated that pipe is probably around a 1000 degrees Fahrenheit
@starszychemik1012
5 жыл бұрын
Black antireflective dye for copper: 20ml distiled/deminerlised water, 2,5g AgNO3, 12,5g Cu(NO3)2. Warm to ~50 deg. C, apply with paitbrush. Rinse with water afer 3-5 minutes.
@tjdot8
5 жыл бұрын
So many things that could be said here however I will not be hypercritical. Super cool. I will overlook the obvious imperfections thanks for the video.
@jeordie43
6 жыл бұрын
Coiling a smaller tube will increase the time of exposure and decrease mass, thereby heating the water faster and hotter and potentially reducing project expense.
@deepakpat
5 жыл бұрын
I too feel so
@kerry9125
2 жыл бұрын
I doubt this would provide much hot water, as the water flowing from the bottle would quickly cool the pipe. Painting the pipe and the water bottle black would help. Using a larger diameter pipe would help also; this would increase the amount of water that stays in the pipe and increase the amount of metal to absorb the solar heat.
@ajarivas72
2 жыл бұрын
A smaller diameter will result in less hot water but at higher temperature
@petes2559
Жыл бұрын
The output water temperature is totally dependent on how fast you get it to flow through the pipe. Much of the heat loss is radiated off the top of the pipe so a high temp insulation on the top of the pipe would help. Something like mineral wool with a melting point of 2150 F glued on with ST-1000 thermal glue can withstand temperature up to 950°C or 1742°F. Problem solved.
@hustlerbiden6815
4 жыл бұрын
That's defiantly worth replicating. Good one
@ahmadnadeemkhalid7276
5 жыл бұрын
Iss k right r left mein (parallel). 2 mazeed pipe lga Ker germ Pani kee storage capacity ziada kee ja Sakti hay.... capacity ziada kernay k iss k ilawa aur b tareeqay ho saktay hein....baherkaif ye buhat nice aur simple project hay Jo her koi aasaan se bna Sakta hay.
@danielbusi
6 жыл бұрын
in the video...please also show the temperature of water that is in the water barrel by putting the thermometer into it...
@antontaylor4530
6 жыл бұрын
Coat the end pieces with reflective material too, so the wood is not scorched. As is, you can start a fire fairly easily.
@tomkcook
3 жыл бұрын
This was my immediate thought looking at this; be very careful how you align it.
@petes2559
Жыл бұрын
The thermal degradation and ignition point of wood and plywood may be generalized by the following: 230° to 302° F (110° C to 150° C): The wood will char over time with the formation of charcoal. If the heat is not dissipated there is some possibility of spontaneous combustion. I doubt this device will get that hot and it has a lot of heat dissipation.
@antontaylor4530
Жыл бұрын
@@petes2559 The slightest misalignment and you will get a hotspot on that wood that could easily exceed those temperatures. The fact that the mirror is parabolic and focuses the sun is the problem here. There are plenty of KZitem videos of people starting fires with parabolic mirrors, you don't want to do that accidentally because you didn't want to spend a few pennies protecting the wood with a piece of mylar or aluminium foil.
@bobfox9916
6 жыл бұрын
One summer when the hot water heater in my motorhome went out, I heated my water by simply using a very black garden hose connected to the water source. It was so scorching in the shower, I had to mix the cold water with it to keep from being boiled alive. I am not sure how that would have played out in the winter, but being in the Deep South, Summertime Sun was more than adequate.
@trevorforrester3142
2 жыл бұрын
I do that right now evey day.
@borysfomichev9100
5 жыл бұрын
avasva has very useful instructions with all details I need
@billtaylor292
3 жыл бұрын
AVASVA IS A FAKE SITE THAT WILL PUT SPYWARE ON YOUR DEVICE
@illumintent
5 жыл бұрын
wondering why you didn't use a coil instead of a line in the heating focal point. were you trying to have the reflective less obstructed? Also why didn't you make the sides reflective? ty
@baranjan4172
2 жыл бұрын
Sides don't matter. They are parallel to Sun rays if oriented right. They won't reflect.
@jarenarenay
5 жыл бұрын
Muy buena idea, vi algo parecido en el que hacen pasar una tubería por varias columnas de latas taladradas y tapado con un cristal
@arkangel8709
4 жыл бұрын
Tip: While working on something that you use a drill as part of the steps, you should use you're drill like a drilldriver" simply by locking an screw driver bit into the drill & use it to drive the screws. Save a lot of time and energy.
@jackrodgersjr
5 жыл бұрын
Useful for RV dweller when parked and will save battery juice. Might also be used to heat van.
@bjl1000
6 жыл бұрын
Yep, I made one of these in 1960, worked very well.
@pacoulemaraicher1829
4 жыл бұрын
On which country please? I leave in France. Can you give us an approximative value of liter per hour or min hot? Many thanks
@7sonderling
2 жыл бұрын
awesome!! hmmm.... why dont you paint that copper tube black, for example with black stovepipe paint? would this not transfer the radiant energy more efficiently? just asking...
@newphysicist
2 жыл бұрын
I should have done that too. Thanks 😊
@shaunnormancroft
6 жыл бұрын
needs a big insulated tank for the hot water to be pumped around the system, instead of a straight pipe needs a coiled pipe wrapped around a pole, the coil pipe painted black can run a solar powered water pump to do this .
@shaunnormancroft
6 жыл бұрын
your wrong with a pump inline the water is evenly heated
@shaunnormancroft
6 жыл бұрын
dont forget my way its pumping round ,so i dont see your point , its evenly heated
@shaunnormancroft
6 жыл бұрын
if you look at how a central heating system works don't that only heat one part till its pumped around?
@shaunnormancroft
6 жыл бұрын
only one way to find out make it , get back to me lol
@rickzap7957
5 жыл бұрын
Good idea bud.
@jeffreylangford962
5 ай бұрын
As a demonstration this is ok, but if you replace the plastic bottle with an insulated metal tank ( an old hot water heater for example) at the top and plumbed the bottom outlet to the tank also the water would circulate when heated and the tank would get very hot. As it is insulated it would store the heat.
@desiman289
6 жыл бұрын
this is amazing. have you built something similar to sea water evaporation to get clean drinkable water using solar?
@raybon7939
4 жыл бұрын
great product id like to live in a boat in key west florida, so what i see for me is a 50 gallon tank,, with a solar pump from the salt water to the tank then use it for showering. possibly some cooking. then another tank with fesh water using one gallon from that tank, to wash off the salt water.
@bjl1000
3 жыл бұрын
Be very careful with parabola's. My neighbor had a curved copper roof on one of his bay windows. The surface focused the suns rays on his soffet and caught the house on fire. No sh*t.
@gershhayes796
2 жыл бұрын
Thumbs up, very nice tutorial. Good luck.
@carltrummer9103
5 ай бұрын
Great project. Thanks for the video.
@objectivecriticism
6 жыл бұрын
Good idea but you need circulation system to heat more water and double insulated tank to keep warm water.
@chimpchowder5774
5 жыл бұрын
Objective Criticism why? It's for hot drinking water not a bath tub! Jeeez
@سعيدثابت-خ5ص
Жыл бұрын
اختراع جميل ..بس لو تكثر الانابيب .وتعمل بلف حراره حق السيارات .ترموستات يفتح عند درجه معينه 82داو92وتعمل قنينه مغطاه مثل السخانه .
@MrCecil_KD9WUS
Жыл бұрын
You need to replace the wood with metal. Ad the wood dries out. It lowers the flash point. After that, you're golden.
@giancha0074
Жыл бұрын
El agua caliente esta en la oarte superior del deposito, es decir que convenientemente solo sacaste el agua fria de la tuberia lo de abajo estara superfrio
@sebastiancochin
5 жыл бұрын
Try using glass tube with black coating or black granules and cover (opposite side off mirror) 1/2side of tube with reflective tape you can show atrem coming out of tap that's 100 ℃
@mrMacGoover
3 жыл бұрын
Im a physicist captain... not a plumber ! No need for soldering faucets or installing pressure relief valves, it's not like water expands when heated...right?
@isabellar1956
5 жыл бұрын
Hello, pls can you give me the measurements of everything because I'm making this project for stem
@Irczyn
11 күн бұрын
U need to cover cooper pipe with black paint :D U see resoults ;) Have a nice day
@danielduplessis8382
Жыл бұрын
Why do you not try it with a grid and a plastic tank to circulate the water to heat up that much. great idea with the solar film I would like to try it
@jjssbailey
6 жыл бұрын
My solar water heater: 5 gal bucket, round glass from microwave oven, water. Place water in bucket, place glass on top of bucket, place in the sun.
@dorianbelen
6 жыл бұрын
Drinking Water?
@carlmeyer449
6 жыл бұрын
John Bailey e
@Darkerpaws
6 жыл бұрын
thats a heat trap?
@davidhirwa3493
3 жыл бұрын
Thank for your working how long it take for heating water
@lalsinghtyagi8135
6 жыл бұрын
It will not work at all. Since there is no water circulation, Online the amount of water traped in Copper pipe will be heated. Also There sud be Black coating on Cu Pipe to absorb more heat
@joelsilas3574
3 жыл бұрын
Bro how did you draw parabola in a sheet any software is there ??
@mSparks43
5 жыл бұрын
how did this work out 1 year on? was it useful? did it survive?
@lm2193
4 жыл бұрын
the physicist who cant differentiate 100 C with 100 F.
@alokt7119
5 жыл бұрын
Use a better thermometer. The idea is good and I should be storing that water in a water heater.
@RamanSingh-vf3ol
Жыл бұрын
Please send link to purchase zinc sheet, which you have folded In parabolic shape
@هاهو-ط1ن
5 жыл бұрын
طبعا تجربه فقط. لان الماء سوف ينزل ثم يبرد النحاس لهذا فهي للتسليه فقط لا يوجد استمرار بالماء الساخن وايضا بصيف وبالنهار فقط لا بستفاد بالليل منها ولا بالشتاء
@ucar_technology
4 жыл бұрын
İncredıble idea.Thanks for video.
@gissie391
3 жыл бұрын
Great NOW WE JUST NEED WAYS OF COOLING THINGS IN DESERT ETC GETTING COLD WATER.
@scottarmstrong5607
3 жыл бұрын
I'd just move, much easier that way.
@gregordonnecaidh6358
6 жыл бұрын
I know it depends on air temperature and starting water temperature, but, what is the average usable rate of flow with this size device?
@ajarivas72
2 жыл бұрын
You recirculate the water and can heat 200 liters of water in a morning
@bhandakeraifoundation4851
Жыл бұрын
Performance in varying temperatures?
@usernamegnu4983
4 жыл бұрын
Лучше будет убрать провисание шланга между нагревателем и коллектором. Напрямую - будет лучше проход теплой наверх и холодной вниз воды. А так - теплая вода блокируется. В прямом виде эта бутылка работает лучше как коллектор (это планировалось, ведь отражатель сделан под углом к поверхности). Еще я бы сделал нагревающуюся трубу больше, пару дюймов. И зайчиков больше поймает и конвекция внутри больше. Как вариант можно пропустить внизу доп.трубу (шланг) от крана до низа емкости. А забор воды из ёмкости сделать с верхнего уровня - там вода горячее. ну и конечно, следует зачернить трубу нагревателя таким образом, что бы толщина покрытия была минимальной и смотреть не по цвету а по теплоприёму (теплопередаче).
@juangonza4979
6 жыл бұрын
Es un milagro que este indú este de una pieza, cero seguridad para todo, sin zapatos, sin guantes, sin ni una wuea, pero el experimento es bueno.
@eduardonunez2164
6 жыл бұрын
Sería bueno que tuviera un retorno para cuando la llave esté cerrada, de esta manera el agua circulará por diferencia de temperatura entre la cañería y el tambor.
@capitanknightfilms3986
6 жыл бұрын
Exacto. Me voy hacer una
@AntonioZett
6 жыл бұрын
The water in the bottle already has a temperature of about 30 degrees. If the copper tube is painted black or dark blue, it will increase the heat🔥.
@macroenergy2828
5 жыл бұрын
good luck in your innovative ideas
@tj-yb1pc
5 жыл бұрын
Good video,,only thing to change is use a coil of copper instead of a single line
@frankenstein3163
5 жыл бұрын
Did this version work better than the spiral coil one you did in 2017 ?
@chimpchowder5774
5 жыл бұрын
I really have to wunder........ Do people even think before posting comments and questions? Oh and yeah that thing will boil water in seconds! Just don't open the valve all the way and you will have a constant stream of boiling water. My satellite dish solar fire can boil a cup of water in less than 2 minutes!
@paulolocatelli8131
6 жыл бұрын
i will copy that and i will put a solar tracker, i like it ;) tks
@richardowens9061
4 жыл бұрын
If it was longer, it could support a higher flow rate. The pipe should be painted black, too.
@markkuhnlein8533
4 жыл бұрын
If you painted the outside of the pipe black, i bet it would get even hotter!
@DanielSan-ch7dr
4 жыл бұрын
The power of a parabolic trough can melt rock and would fry any paint added to it. The idea of thos type heater is basically instant water heater and if you recycled the water back through tank you could make it well above boiling temperature creating steam which could distill into pure water.
@randypratt2887
7 ай бұрын
Pretty cool but can you use it to heat your home 😊
@NCAirwayss
4 жыл бұрын
The pipe on the focal axis. Why is it not painted black? Use small dia long pipe, coiled or multi-loop if needed The effect could have been more pronounced. A brilliant job, nonetheless. What to do with the water at 100 deg C? If you could convert into electricity, it will be a fantastic thing to do.
@freddyfourfingerz9126
6 жыл бұрын
That can probably accommodate more than just 1 copper piping, giving nearby people access to their own hot water as well.
@narindersingh1708
2 жыл бұрын
Ap center copper coil water ke uper Balck colour karna zaruri he
@lancemumford3106
3 жыл бұрын
Very interesting video, keep up the good work. Thanks !
@emmanuelunitedchurchottawa4152
3 жыл бұрын
I think I have a new summer project. Paint the pipes black, use multiple pipes? Maybe a black plate over the pipes? But I think i will wear shoes while cutting :-)
@vabalatax66
3 жыл бұрын
Kalo malam hari air msih tetep panas ga?
@leepu747
Жыл бұрын
Can I boil the water means temperature 100 degree
@reinamopardo4435
4 жыл бұрын
Hola me gustaría saber todas las instrucciones y medidas , para hacerme one solar water heater , no somos personas pudientes y vivimos en las montañas , le agradecería si me envía las instrucciones para hacerlo yo misma GRACIA Y MIL BENDICIONES
@faustominuzzo9263
Жыл бұрын
Grazie!!! Puoi indicarmi i gradi di iclinazione del pannello solare? Grazie! Fausto (Roma, Italia) 21-07-2023
@jagadeeshreddy1921
9 ай бұрын
Could you please tell the thickness of the zinc sheet
@necom3537
6 жыл бұрын
Put a gallon of water under the hot sun, you will get a hot water same like you got. but the idea to make a solar panel is nice
@NSNG1540
6 жыл бұрын
Good. How about covering it with glass or acrylic to retain heat ..
@tominjose1993
6 жыл бұрын
If it is more than 100" then water will boil and starts to evaporate or at least we can see some steam!! bro nice ayitte thalliyathanalle?:P
@ranz1513
3 жыл бұрын
Steem cake,,( puttu. )
@arnabsen6358
13 күн бұрын
Can you please send me the solar reflective film buy link
@beshoykaram7728
8 ай бұрын
Solar Reflective film what is its material ? How can i get ?
@myoneblackfriend3151
6 жыл бұрын
Thank you for sharing your idea. I like it.
@fjalics
3 жыл бұрын
Nice work. Hope you got a cordless screwdriver, and a thermometer that measures over 100 C or 212 F.😉
@cforchemistrybysirshahzad
Жыл бұрын
Is this aluminium foil sheet U sticked on steel sheet n is this a copper pipe??
@newphysicist
Жыл бұрын
It’s solar reflective film and copper pipe
@csselo
5 жыл бұрын
very good but if the pipe heats plastic hose become a problem
@m1a1idea.s96
3 жыл бұрын
Use foile type product ???
@inamhaq6415
5 ай бұрын
Ye sheet kis material ki ha
@michaelmaged1957
5 жыл бұрын
I think that it is better if you paint the copper rod with black paint inorder to change the UV rays of the sun into heat as much as possible
@phitrow
6 жыл бұрын
if you connect a steam engine here and loop the water, you can get a lot of traffic or electricity. si aquí conectar el motor a vapor, mientras que el agua de repetir, puede recibir una gran cantidad de movimiento o la electricidad.
@magicsathish1
6 жыл бұрын
Wldone bro give a black coating to the copper pipe
@newphysicist
6 жыл бұрын
sathish kumar, Thank you.🌸
@Krommandant
6 жыл бұрын
A black coating to the water tank will help pre-heating too.
@charlimat
6 жыл бұрын
New Physicist , what are the measures of Qs and Ps?
@sosteve9113
6 жыл бұрын
good comment
@Kiyarose3999
6 жыл бұрын
I’m surprised you didn’t paint the Copper pipe Black, is there a reason for this?
@chetan.gondaliya
6 жыл бұрын
This is cheapest and awesome concept!!
@javedkazee
6 жыл бұрын
When pipe water will finish then tank water will give same temperature???????
@tatooetugo
3 жыл бұрын
Faudrait pas plusieurs tuyaux?
@ВладимирИльин-о4к
3 жыл бұрын
If the surface of the copper tube is blackened using any of the simplest methods, the heat transfer will increase by 15% or more.
@-HardyAdityaChandra
11 ай бұрын
nice one homie
@napcdosa529
3 жыл бұрын
My suggestion is to make several lines instead of just one copper pipe to improve thermal efficiency.
@lowrads3653
5 жыл бұрын
With a one way valve and a return line, it could probably keep an entire tank warm.
@FriesinNF
4 жыл бұрын
This is the best!
@jaimecabal9809
6 жыл бұрын
How efficient is it? For how long is the output at that temperature?
@anibal60100
6 жыл бұрын
muy bueno mi amigo, muchas gracias por el video
@Kundankumar-gj5fr
4 жыл бұрын
Which material of tube use to flow of water to heating ???
@draaitol
5 жыл бұрын
Heating up water means expansion, looks like a closed system?, if it would be 100 C/steam, the thing is a bomb, probably you have to search for the tap or call NASA for that white cap on top, use a vent or pressure valve maybe?
Пікірлер: 474