I did a z40 race cam and a vm26 with a 17 front sprocket it made that little 125 a monster pulled hard as hell and hits 65 mph gps no problem
@user-uc5tj6ux8w
Жыл бұрын
Red thread locker on a chain sprocket? Dude, lol. Have fun removing that in the future. Blue is what you should have used.
@near--zero
2 ай бұрын
the sprocket was probably covered in cosmoline to begin with so the threadlocker was probably less effective than if it were clean.
@elluchador1251
Жыл бұрын
Thanks for all the info. We pick up a used venom last weekend. Literally just a handful of miles, the dash doesnt light up nor the taillight, brakelight. Any suggestions? it runs fine, although we havent ran it for very long. didnt get a title only BoS/ they lost the title.
@nickmark9576
Жыл бұрын
Check the fuse under the seat? If not that check the green and red one wire connectors
@_BlueCollarGamer
6 ай бұрын
for the emissions delete do you even have to weld it? I do not have a welder... I was going to just crimp it real good and throw some JB on her... do you reckon this will work?
@nickmark9576
6 ай бұрын
En 50/50 it’s gets reallly hot because it’s exhaust coming out and it’s constant pressure so it would be best to weld but high temp jb weld Might do
@_BlueCollarGamer
6 ай бұрын
@@nickmark9576 Okay for sure.. Im going to start there and if it doesnt hold up I will have to find a local mobile welder. Thanks for the quick response and input dude!
@joejoemoonar
18 күн бұрын
What does deleting the control safety do?
@49erPaddler
6 ай бұрын
What exhaust is on your bike? Love the high mount.
@TurboSJR
Ай бұрын
is there amy chance you have the links for everything??
@kevinjones4347
Жыл бұрын
Great video love to see it..
@FernandoMartinez-ev8iz
Жыл бұрын
what about the house that goes towards the tank where canister was
@Lek.Scrolling
Жыл бұрын
Would you sell the plate for the motor mount same size and the 2 holes for the bolts?
@DIYdashGAMING
11 ай бұрын
Would you be will to ship me a third mount ready to be installed?
@prk2a918
Жыл бұрын
Thank you for the video!!
@ianlacour3947
Жыл бұрын
What jets are you running on the vm22 and what is your elevation
@nickmark9576
Жыл бұрын
The jets that came with the carb
@fernandomartinez-oh7sj
Жыл бұрын
what if we dont have a welder?
@user-uc5tj6ux8w
Жыл бұрын
You can cap it off.
@fernandomartinez-oh7sj
Жыл бұрын
@@user-uc5tj6ux8w like close the end of hose or what?
@user-uc5tj6ux8w
Жыл бұрын
@@fernandomartinez-oh7sj Yeah or use a plate to block the exhaust port.
@fernandomartinez-oh7sj
Жыл бұрын
@@user-uc5tj6ux8w have you changed the motorbolts grade 8?
@jawwhs
Жыл бұрын
wtf did i just watch you speed run a grom 😂
@nickmark9576
Жыл бұрын
Pretty much lol
@jawwhs
Жыл бұрын
@@nickmark9576 makes me mad to see the way you did it so fast and how long it took me 😂
@jawwhs
Жыл бұрын
@@nickmark9576 do you have a back sprocket?
@user-uc5tj6ux8w
Жыл бұрын
@@jawwhshe cut out all the dead time in between.
@danielmirra1261
Жыл бұрын
Yooo bro I have a stretched grom clone and I can’t get it to go up at all lol I’m not new to doing wheelies either
@nickmark9576
Жыл бұрын
The purpose of a stretch is so it doesn’t wheelie hope this helps…
@user-uc5tj6ux8w
Жыл бұрын
Squid. Longer wheel base is to prevent pop up/wheelies.
@_BlueCollarGamer
6 ай бұрын
@@user-uc5tj6ux8w isn't a squid somebody who rides like an asshole putting everybody else at risk? Just asking
Пікірлер: 34