I've been looking for a way to use a servo or some type of drive motor to push in and out for a short distance. Watching your video gave me some 💡s . Thank you.
@philliptoone
6 жыл бұрын
Well, that is one way of doing it. And I had assumed you would just disconnect the potentiometer to give a constant error to the feedback so that the speed could be controlled from a microcontroller. I'm curious why you bothered to remove and modify the potentiometer if it is now only used as a output shaft.
@MrExpert
Ай бұрын
to get torque. it was difficult to find high torque small geared motor.
@philliptoone
Ай бұрын
@@MrExpert Yes, I understand this. I've also modified these little servo motors for high torque, low speed applications. But I've just removed the potentiometer and driven the motor with pulses the say way you would drive a normal servo motor except to control speed rather than position. But I can see that this approach allow someone to avoid the use of a microcontroller and control the speed through voltage rather than pulses.
@Nathan-zg5kp
7 жыл бұрын
0:12 OCD crooked sticker
@4Nissankas
7 жыл бұрын
hey buddy ..how do you connect the wires at last,that bi is not there..i did the same as you did n canot run the motor as wire connection !!1..if you could advise would be great!thx sam
@RenatosilvaMinis-Games
6 жыл бұрын
Muito top
@wildanfadhil877
Жыл бұрын
Apakah ini bisa digunakan pada rc quick Drive?
@danielesp3458
7 жыл бұрын
This work with 1.5v AA baterry?
@LOMKA-x3g
2 ай бұрын
Does it work with Panasonic?
@ushadevi3223
6 жыл бұрын
Video is running so fast
@sulemanhassanali
3 жыл бұрын
I adjusted its speed to 0.75. KZitem provides that option for every video.
@RottnRobbie
2 жыл бұрын
What you're doing is exactly what I wanted to do for a project I have in mind, right down to the label on my servos being the same as on yours. But the video is a fail, because it obscures and leaves out the important parts. Undo the screws, cut the label it's open... kinda obvious. OK, half a point for showing cutting off the "nub" on the gear. But I absolutely *CANNOT* tell what you're doing with the screwdriver and pliers between 1:35 and 1:55. Removed something? Bent something out of the way? Removed or bent _what_ ? And why? It looks like the motor is sitting there untouched. Then at 2:30, suddenly and magically and _OFF CAMERA_ two new wires get connected to what we are left to assume is probably two of the four wires that were cut earlier. But what those two new wires are connected to is never shown. If you're going to do a "how to", then don't leave out steps, and fast-forward through other critical steps.
@pudsr2497
8 жыл бұрын
Yes cool
@hilmidwiputranto6944
7 жыл бұрын
why would I do this if it just would be the same as a normal DC motor anyway
@sharojalhasan7852
5 жыл бұрын
o .. Now its high torque dc motor
@davidroberts1852
7 жыл бұрын
Hack complete at 0:55
@KurumiZph
7 жыл бұрын
Wait wait wait, what, you are not even connecting back those wires. Also what is the reason for cutting them?
@MrExpert
7 жыл бұрын
Normally servos can't rotate 360 degree and thrs wire for signal. for continuous rotation we need only 2 wires + and - .
@tayyc719
3 жыл бұрын
thanks
@priyanshmehta5668
7 жыл бұрын
Which was name of wire you used last? Can you tell me the link where I can buy in India?
@aaditya9030
4 жыл бұрын
Tats a jumber wire..u can search for it it's easily available
@fajarriyanto2140
6 жыл бұрын
Amazing
@totape4161
7 жыл бұрын
Can you give me the code for Arduino IDE for the servo rotate 360degrees?
@anmol4484
3 жыл бұрын
Um bruh the servo can only spin 180 degress as long as u have some modification like he did
@melihapa3884
Жыл бұрын
Hızlandırılmış video olduğu için ne yapıldığı hiç anlaşılmıyor
@pipoypipoy7796
4 жыл бұрын
what is the name of the song?
@rosemondcardoso4919
6 жыл бұрын
Can we control servo with 10k potentiometer
@MrMarkozcortez
6 жыл бұрын
Hey bro you didn’t show how you connected the cables is not on min. 0.55
@MrExpert
6 жыл бұрын
Hello. Just connect the 2 wires to a DC motor as you would normally. Cheers
@bedok790
3 жыл бұрын
Servo motor 360 and turn back
@orange_tweleve
2 жыл бұрын
just why not buy a gear motor ? they are so much cheaper yk
@MrExpert
Жыл бұрын
Torque
@scienceinnovativebrain
4 жыл бұрын
very nice #scienceinnovativebrain
@raikku2971
3 жыл бұрын
For what purpose would anybody want to have continuous rotation servos?! I cannot comprehend it.
@MrExpert
3 жыл бұрын
to use as powerful mini geared motor.. i Have used a lot in my projects.
@germancarrasco2028
6 жыл бұрын
Why? Simple motors are cheaper...
@tylermontero7104
5 жыл бұрын
G erman C arrasco some servos have more power
@Sohilkhan63959
3 жыл бұрын
Bro i m using mobile charger
@abpccpba
5 жыл бұрын
Way to fast be more delibert.
@dwiwahyu2804
3 жыл бұрын
This is a not input program
@nksaini3045
2 жыл бұрын
Bhi kisi ko ye chye
@thecrazerkid2146
4 жыл бұрын
Ohhhhhhhh i get it thirs a chicken nugget stoping it from going 360
@nksaini3045
3 жыл бұрын
Aap Humse hundred rupees mein le sakte hain
@achumons5766
3 жыл бұрын
Dead
@olimpioamaral3517
2 жыл бұрын
fake fake fake fake ele e experto
@StueySmall
Ай бұрын
how about you slow down at the important bit that probably most people are here to see instead of whatever this was god damn. did you watch this video before you posted it?
Пікірлер: 55