I got mine done today, worked perfectly doing it this way, thanks so much for posting it! The only thing I missed was TWO rod sleeves, I had picked one up, then was doing this project, came up short of hooking it to the pin on the base, went back and watched again, ran to town for another rod sleeve! Thanks again!
@NetBuddyFishing
2 жыл бұрын
Great to hear, I think you will enjoy it with this setup. We had to use 3 sleeves on my Brother's Mega Live Install!
@recordattheroom
Жыл бұрын
Very good video I do the same thing I switch to the pole ducer and now I’m back on the trolling motor. That’s the only way to run it bass fishing have had zero problems.
@NetBuddyFishing
Жыл бұрын
Yes, I couldn’t imagine not having it on the motor.
@StructureFishing
2 жыл бұрын
I have a Minn Kota so I like the way you installed it. But why do most say it should be installed on the shaft, at least 7" above the motor?
@NetBuddyFishing
2 жыл бұрын
They are mounting it on an Ultrex, which allows a shaft mount. The 7 inches has to do the the angle of the shaft mount to clear the motor barrel. For other motors like the Terrova, the shaft mount is not an option as the shaft slides through a housing. You can barrel mount on a Ultrex too with no interference, but just have to be careful if you fish in shallow water to make sure your not banging bottom or stumps. You’ll get a better return with a barrel mount because you can have a 0 degree angle to the lake.
@StructureFishing
2 жыл бұрын
@@NetBuddyFishing Great! Thanks for the quick reply! You don't seem to see many that mount the livescope transducer on the barrel. Not sure why. Thanks again.
@mattkoogler8170
2 жыл бұрын
I have a 3d printer and you can print things soild and out of tons of different materials
@NetBuddyFishing
2 жыл бұрын
You are correct that it is possible, but it is not the norm for what is out there.
@daveholte7658
7 ай бұрын
Looks like a great alternative from pole mount. But assuming I would not be able to tarp and travel with boat cover as the pressure on the 334 would not be good? Thoughts? Great video
@jmg1910
7 ай бұрын
How do you find the livescope when you are spot locked and vertically jigging for walleye or lake trout? Is it a big problem when the motor adjusts direction?
@After5Outdoors
2 жыл бұрын
👍
@TimSmith-jc2ld
Жыл бұрын
Can you post a link for the cable protector? I am not finding on your webpage.
@NetBuddyFishing
Жыл бұрын
I discontinued it, I don’t think it was adding a lot of value. Electrical tape at the base to attach the sleeve will do the trick. I did that for 4 seasons before making the protector without issue.
@craigholland2274
2 жыл бұрын
Great idea thanks.
@aaronambur
Жыл бұрын
Good video and appreciate it. When you automatically stow the motor, do you need to baby sit it? Meaning, I see when you manually stowed in in the video, you grabbed the loops and brought them up over the cradle. Thanks....
@NetBuddyFishing
Жыл бұрын
I would not do an Ulterra Auto stow and deploy this way. You will likely pinch the cable. There is a video out there where they uses a coiled bike lock on the side for the ulterra cable, that seems like a much better idea.
@aaronambur
Жыл бұрын
@@NetBuddyFishing okay.... Just saw that you were showing an Terrova and not an Ulterra. My bad. I will look for that video. Appreciate the quick response.
@christophereric1407
6 ай бұрын
Watching one year later. Any experience with your system and the Ulterra automatic deploy? Cable management is the concern. One could not wrap the cable around the Ulterra post like you do with the Terrova. If there is a tangle or knot, the Ulterra deploy motor is strong enough to pull the transducer cable off the transducer. Which is not good. Perhaps I try to rig it up with 14/2 wire in a rod sleeve as proof of concept before I tie my MegaLive transducer cable to the Ulterra bullet. Thoughts?
@NetBuddyFishing
6 ай бұрын
You can’t do this with an ulterra. You’d need a different way to do cable management. I’ve had this on my terrova now for 6 seasons no issues.
@upthecreekyt
6 ай бұрын
What if you wanted to use perspective mode mounted on the barrel?
@NetBuddyFishing
6 ай бұрын
Not really possible in a good way. Would need to get something like a cornfield mount, and you’d experience a lot of vibration and wobble in perspective on it.
@donnysbackroadoutdoors5088
Жыл бұрын
How do I order the cable protector?
@NetBuddyFishing
Жыл бұрын
I changed it a little bit. This is better thenetbuddy.com/universal-live-imaging-cable-sleeve-and-rubber-cable-protector/
@jones1394
11 ай бұрын
I try to see after you put it on how much kickout do it ha e??. I'm trying to mount myself to the trolling motor but looking at it fron the front that kickout looks like its doing out into space instead of in front of the trolling motor. Suggestions???.
@NetBuddyFishing
11 ай бұрын
I am not following what you mean by kickout?
@donnysbackroadoutdoors5088
Жыл бұрын
Will this work on the Minn kota ulterra
@NetBuddyFishing
Жыл бұрын
not this method. There is a bike lock coil method that works good for Ulterra cable management
@christophereric1407
6 ай бұрын
I asked donnys question just now. Might you show us how the bike lock coil works on an Ulterra?@@NetBuddyFishing
@craigholland2274
2 жыл бұрын
Do you have an Amazon affiliate link for the barrel mount so I can support the channel?
@NetBuddyFishing
2 жыл бұрын
I don’t, maybe soon, they have a lot of rules around consistency. Thank you though, glad this will work for you.
@craigholland2274
2 жыл бұрын
@@NetBuddyFishing Not a problem, thanks . I just ordered the wire protecter.
@ojsimpson39
Жыл бұрын
Where do i find the cable protector?
@toddyell4440
Жыл бұрын
Hello, having it mounted to TM, and on spotlock, will that affect the imaging? I have mine on a mounted and image is great, but always looking for better system. Your mount says for hummingbirds, would it work with Garmin Force?
@NetBuddyFishing
Жыл бұрын
No interference. I have some other videos where I record the screen while targeting walleyes.
@carytoms9500
Жыл бұрын
So the trolling motor doesn’t interfere with the live scope ?.
@NetBuddyFishing
Жыл бұрын
No
@Tighterlinesfishing814
Жыл бұрын
So i just mounted mine like this yesterday but the install directions for forward mode did not have it sitting like you had. It had it slightly canted upwards and forward not straight???
@NetBuddyFishing
Жыл бұрын
The 32 or the 34? The 32 to top should be flat for forward mode. Or, it can be mounted facing the other direction, where then the bottom would flat. The 34 has a slight tilt up.
@Tighterlinesfishing814
Жыл бұрын
@@NetBuddyFishing Yup my bad i didnt notice that was a 32. Your spot on man.
@timculpepper8730
Жыл бұрын
Where can I buy the cable connector.? I did not see it on the web site. Thank you!
@NetBuddyFishing
Жыл бұрын
Discontinued, using electrical tape at the base of the transducer is sufficient to connect a rod sleeve.
@BlackCobra331
2 жыл бұрын
Any interference?
@NetBuddyFishing
2 жыл бұрын
Nope, take a look at my sniping walleye video’s.
@calebleger
2 жыл бұрын
I have a totalscan transducer for my Lowrance unit on the barrel of my terrova. Have you had any experience with barrel mounting livescope as well as another transducer other than the humminbird one that's built in? I'm worried with it being so close to the totalscan that there will be interference.
@NetBuddyFishing
2 жыл бұрын
I have had Livescope barrel mounted for 5 years now, 0 interference issues.
@AllSeasonFishing
Жыл бұрын
Did you use spinning or casting rod sleeves?
@NetBuddyFishing
Жыл бұрын
Casting.
@toddeberspacher5085
2 жыл бұрын
Can you use the transducer in perspective mode with this setup?
@NetBuddyFishing
2 жыл бұрын
No, but I don’t think you won’t like using it in perspective on the trolling motor. It’s really hard to understand what’s going on when the transducer is moving around in perspective. I tried it for 2 weeks when it first got released and hated it, but use it ice fishing when it’s stable. I think forward mode is best for finding and hunting down fish, and is most efficient on the motor. If your going to sit in one spot and cast a school all day, perspective is pretty cool and might be worth getting a pole. I personally use forward 99% of the time, and will flip it into down if I am vertically jigging Lake trout in 80-100FOW.
@Bshug87
Жыл бұрын
I can’t find the cord saver on your website am I over looking it?
@NetBuddyFishing
Жыл бұрын
Hey Brandon, Yes, I discontinued them. I found they were not needed after a year of using, with the changes Garmin made to their cord. Electrical tap to attach the cable sleeve would work good. I did this for 4 years with no issues.
@Bshug87
Жыл бұрын
Ok sounds good thank you
@davebruns6850
2 жыл бұрын
What motor is this?
@NetBuddyFishing
2 жыл бұрын
This is the Terrova but it can work on any barrel.
@davebruns6850
2 жыл бұрын
Thanks! This is perfect info for me, I’ll be putting a new Terrova on and adding my LS to it as soon as I get my boat out of winter storage…. I appreciate your video!
@NetBuddyFishing
2 жыл бұрын
@@davebruns6850 Nice, good luck with the install. If any questions pop up find me on social media or email on the website and send them over, I'd be glad to help.
@dannylang7971
7 ай бұрын
Is this barrel mount a 0 degree mount.
@NetBuddyFishing
7 ай бұрын
Technically No, but you just rotate the hose clamp around the barrel until the ducer is at 0.
@dannylang7971
7 ай бұрын
@@NetBuddyFishing do you just eye ball it or do you use a level
@NetBuddyFishing
7 ай бұрын
@@dannylang7971 I just eyeball it.
@dannylang7971
7 ай бұрын
Thank you sir for replying.
@MrDereksykes
Жыл бұрын
So in this video, that is a zero degree mount, barrel bracket? Wondering if the barrel mount that comes with the LVS32 is standard zero degree or purchased separately?
@NetBuddyFishing
Жыл бұрын
It’s the standard barrel mount, but it’s set at 0 degrees before I tighten it down.
@MrDereksykes
Жыл бұрын
@@NetBuddyFishing Have you had any experience fishing shallow water (10' or less) with the ducer being mounted to the TM barrel? Wondering if there is any interference or noise due to barrel mount in shallow water (like for crappie fishing open water suspended fish)
@NetBuddyFishing
Жыл бұрын
@@MrDereksykes yes, all the time, no barrel interference
@brettjohnson6647
2 жыл бұрын
Will this work with the lvs 34?
@NetBuddyFishing
2 жыл бұрын
Yes, I know of people who have mounted LVS34's, Active Target and Mega Live this way. You just electrical tape the rod sleeve to the transducer at the base vs using the cable protector like we do in this video.
@brettjohnson6647
2 жыл бұрын
Awesome. Thsnks!
@joshsimmons2044
10 ай бұрын
This is not on your website
@NetBuddyFishing
10 ай бұрын
I discontinued the plastic protector. I did not like that it created a rub point on the cable. I changed it to a rubber one with neoprene sleeve.
@joshsimmons2044
9 ай бұрын
@@NetBuddyFishing I ordered what you sell now seems to be good quality thanks
Пікірлер: 72