Thanks for getting to the point, with no stupid music or unnecessary dribble. I want to paint some radio enclosures and this is exactly what I was looking for - thank you!! Learned everything in under 5 minutes!
@cwguy8960
3 жыл бұрын
This was months ago - but btw the radio enclosures came out GREAT! Thanks again!!
@chrisczub4930
11 ай бұрын
### Conditions * Well ventilated space * Little no wind * 60 to 85 Fahrenheit * Relative humidity
@sgtrutters5892
4 жыл бұрын
Never thought of covering it with a box while it dries!!
@StompBoxParts
4 жыл бұрын
Totally! Just make sure you get the dust out of the box before using or you're not really helping yourself.
@fataldiz133
3 жыл бұрын
A very careful and well-explained approach! Excellent results. One of the my favourite channels in nowdays and has only 3 videos apploaded! Keep on the great job!
@neilwishart3162
3 жыл бұрын
Good video. After various trials and errors over the years, I've came to the same outcome as you've shown in your video. Viva Pedal Builders!
@tbaret15
6 ай бұрын
If I use a textured paint, will that cause problems with applying a label and getting it to stick?
@StompBoxParts
6 ай бұрын
Depends on how textured. If you're applying waterslide/sticker/label that cover the whole face of the pedal, the texture may cause issues. Smoother or flatter paints will work better in that case. If you must use textured, you'll probably need to apply several layers of clear coat to smooth it out a bit.
@adrianguti8749
Ай бұрын
You really waste water dude… had to stop watching, made me anxious.
@StompBoxParts
Ай бұрын
You're right, should have went with the brushing teeth approach and turn off the water between rinses.
@arielomc
4 жыл бұрын
Very very very good tutorial. Thanks folks!
@SurfaceDweller
Ай бұрын
Thanks!
@clebersonsilva3021
3 жыл бұрын
Excelente trabalho amigo, meus parabéns 👏👏👏
@eitanpetel
2 жыл бұрын
Thank you very much, this is very helpful!!!
@braaandooon3166
5 ай бұрын
Still bummed Rustoleum discontinued their Hammered green and blue hues.
@cyanotypical
4 жыл бұрын
This is really helpful!
@seangarland
3 жыл бұрын
I’ve just started building my own pedals from DIY kits, and this video looks like exactly what I need in order to make my pedals look nice. Thanks!
@anselmountain6884
8 ай бұрын
how to get these Blemish finish on enclosure ?
@AntHenson
3 жыл бұрын
Instant sub. Brilliant walkthrough
@waynegram8907
10 ай бұрын
An other method of coloring a pedal enclosure without using paint or spray paint? I live in an apartment so I can't use spray paint inside or outside without getting a citation
@StompBoxParts
10 ай бұрын
If those are your limitations then it would definitely make most sense to buy something already powder coated or painted.
@xbfo8053
6 ай бұрын
Thats awesome! My friends designed a graphic for me and i was wondering if you could paint on the painted pedal with posca markers? It is a hand drawing and i dont want to print it. Thank you 😊
@StompBoxParts
6 ай бұрын
Can't see why that wouldn't work. Let the paint on the enclosure adequately dry before using markers.
@xbfo8053
6 ай бұрын
@@StompBoxParts Thank you!!
@candrabalimirage
2 жыл бұрын
Like#440 and Subscribed. Thanks 4 Ur Video !
@rokinrandy
2 жыл бұрын
That krylon No runs plus glossy coat was already built in the paint pre installed for one coat. the first attempt looks pro no sanding..let sit in the hot sun..Didn't have luck with rustoleum ,metallic looks like storm clouds and my crackly feet..After I added their rustoleum clear coat.
@StompBoxParts
2 жыл бұрын
Lots of ways to accomplish this! Glad you found a method that works for you!
@ritualsofthedarksun
Жыл бұрын
I wanna re-paint all my pedals. Boss, etc. Does it work the same way?
@jb04evanivich
Жыл бұрын
I repainted a Joyo pedal, boss should also be using a metal enclosure. I used some paint stripper and scraped the paint off with a wide metal scraper, then used sandpaper (starting large and then getting finer) under running water. From there you just follow the video
@rhodesyguitar4467
8 ай бұрын
How do you create you labels
@StompBoxParts
8 ай бұрын
Lots of ways....but check out our other video for a relatively easy way using labels you can run through a printer!
@slushedpuppy8044
Жыл бұрын
what type of clearcoat is most commonly used for pedals? Matte, satin, gloss?
@StompBoxParts
Жыл бұрын
Not sure what's most common but I usually grab gloss if going the paint route
@habri013
10 ай бұрын
What is gained with sanding in between layers? Others recommend it but you're not doing so and this result seems fine from what I can see.
@StompBoxParts
10 ай бұрын
If the paint is still wet do not sand. If the paint is dry, sanding will help the new coat stick better and flattens out the dry coat. Certain finishes (like hammertone used in this video) simply don't work with sanding because you'd be sanding off the hammer texture.
@kylemiska8353
Жыл бұрын
24 to 48 hours is a long time 😢
@LeecheMusic3
2 жыл бұрын
No I’m gonna wait 3 mins
@StompBoxParts
2 жыл бұрын
Might as well just scrap it after 2 mins and 5 seconds
@benebluesman
Жыл бұрын
Thanks for the video.
@yousayidontknow
3 жыл бұрын
I'm planning to just repaint my old pedal.. is it okay to just sand my old pedal to remove the paint or there's another way of removing it?
@StompBoxParts
3 жыл бұрын
Sanding is perfect!
@jimwheeler5278
3 жыл бұрын
Any reason I wouldn't want to use a base coat paint that includes primer, like Rust-oluem Painter's Touch 2X Ultra Cover Paint + Primer? Could this remove the primer spraying step completely?
@StompBoxParts
3 жыл бұрын
Might work fine for you but I can't know for sure. The typical downfall of paint/primer is that it isn't made to adhere well to metal, thus why we recommend the self-etching primer.
@jimwheeler5278
3 жыл бұрын
@@StompBoxParts Okay. Thanks. You didn't mention sanding between coats. Is that not necessary? Do you do any sanding at all? If you do, what grit do you use?
@StompBoxParts
3 жыл бұрын
@@jimwheeler5278 Not necessary! (and actually not recommended until the paint is completely dry, which takes a day or two)
@kdubatx1
Жыл бұрын
Super helpful video
@sivletalk2003
3 жыл бұрын
If I want my pedal to gradually degrade and chip overtime, could I just only do the base coat? Or would it all come off quite quickly?
@StompBoxParts
3 жыл бұрын
That would be an option, but clear coat might be necessary depending on how(/if) you're labeling. Or skip the primer. It'll chip much quicker without the primer.
@sivletalk2003
3 жыл бұрын
@@StompBoxParts I'll just be sharpieing on vol, gain, etc haha. And alright, I'll do that. Thanks!!
@sivletalk2003
3 жыл бұрын
@@StompBoxParts Found some cheap-ish spraypaint from a few years ago that has mixed-in primer - should do the trick! lol
@seangarland
3 жыл бұрын
Do you use any sort of naphtha or acetone after sanding to clean the pedal prior to primer?
@StompBoxParts
2 жыл бұрын
Soap and water to clean, wipe it off and let it air dry like in the video. You could use naphtha or acetone or isopropyl alcohol to speed up the drying process but it's not necessary.
@mearimfishing3394
Жыл бұрын
AMAZING !!!!
@herald9
3 жыл бұрын
For the labeling, did you perform the same steps you did from your "How to Add Labels.." video?
@StompBoxParts
3 жыл бұрын
For the pedal graphics in this video I used a vinyl stencil. You can insert just about any method of adding labels in that section of painting your pedal assuming the base coat in dry enough to handle. Stencils, decals, stamps, etc.
@lonewolf42187
3 жыл бұрын
@@StompBoxParts I have a Cricut. Will that suffice for labels?
@TrippLilley
2 жыл бұрын
@@lonewolf42187 yes. You can use a Cricut either to cut stencils for painting labels, or to cut vinyl labels to stick directly and then clear coat over to protect.
@jimbaaab
2 жыл бұрын
Thoughts on baking the enclosure in a toaster oven between coats?
@pittuthead
3 жыл бұрын
Nice work dude! Subscribed!
@jdb2722
3 жыл бұрын
Where do you get labels?
@StompBoxParts
3 жыл бұрын
Check out our other video on how to label pedals!
@jdb2722
3 жыл бұрын
@@StompBoxParts I watched them all! Thanks for the help. I bought letter stencils and was going to paint them on but stickers seems far easier.
@thelachster
3 жыл бұрын
Thanks for the video! Is there any way of painting a pedal that is already fully assembled? Like a pedal you bought that didn’t have a paint finish on it by design, but you want to add paint to?
@StompBoxParts
3 жыл бұрын
Totally doable! Disassembly would be required to paint the entire enclosure, however.
Пікірлер: 65