make a video on connecting the jk bms inverter with the CAN bus
@Fester_
Ай бұрын
Good job, thanks.
@stephanauguste4008
Ай бұрын
Very useful
@Alexmrg123
Ай бұрын
I guess answer will be NO, yet it can be a feature to implement for this inverter in next releases. question is: can they merge phases in parallel mode? for example I do connect 2 or 3 inverters inputs to different phases and I want to get more powerful single phase on outputs
@PowmrSolar
Ай бұрын
This model supports single-phase and three-phase parallel use.
@user-ez2jl3or2y
23 күн бұрын
make a video on connecting the jk bms inverter with the CAN bus@@PowmrSolar
@sergeyleonidov3015
Ай бұрын
Can you please tell me what the energy consumption in standby mode is for each of the three inverters?
@PowmrSolar
Ай бұрын
Less than 124W.
@NadishanMaduranga
Ай бұрын
thank you for sharing
@MrFenno1978
Ай бұрын
How many devices can be parallable?
@reenreen3959
Ай бұрын
Up to 12 units with the LIP version.
@michalanonymni7916
Ай бұрын
3F parallel output 380V or 400V? the mitsubishi zubadan pump wants 400v so i don't know if this unit will work with that
@PowmrSolar
Ай бұрын
A single machine can output 240V in single phase, and the machine can operate in parallel with three phases.
@Alexmrg123
Ай бұрын
hello I'm very interesting in this inverter mode. is it necessary to connect both inverters to same battery? will it work in next situations: inv1: PVarray1+utility+battery inv2: PVarray2+utility OR inv1: PVarray1+utility+battery1 inv2: PVarray2+utility+battery2 thanks for your answer.
@PowmrSolar
Ай бұрын
2 machines can be connected to the same battery. The machine will work according to your settings. After paralleling, the slave will follow the host's settings.
@Alexmrg123
Ай бұрын
@@PowmrSolar can or should? I know it can be connected to same battery. But is it mandatory condition? Is it allowed to connect separate batteries per inverter? Considering batteries require same voltage/amps setup.
@alros1990
14 күн бұрын
@@Alexmrg123 from user manual: WARNING! Be sure that all inverters will share the same battery bank. Otherwise, the inverters will transfer to fault mode
@user-wy3lu7tj8t
Ай бұрын
Good upgrade of battery terminal. what is the pc software for the inverter?
@PowmrSolar
Ай бұрын
This model does not have pc software. Please use wifi module for monitoring.
@user-ez2jl3or2y
23 күн бұрын
@@PowmrSolarmake a video on connecting the jk bms inverter with the CAN bus
@alros1990
19 күн бұрын
Does it can be used in parallel with no battery at all?
@PowmrSolar
17 күн бұрын
Nope, if you want to use it in parallel, you must connect the batteries.
@Alexmrg123
Ай бұрын
can it communicate with FelicitySolar lpbf48300 battery via RS485 or CAN? my current MUST inverter can't comunicate with battery
@PowmrSolar
Ай бұрын
You need to consult your battery manufacturer for this.
@Alexmrg123
Ай бұрын
@@PowmrSolar battery manufacturer says: "Compatible Inverters Felicitysolar/Deye/Luxpower/Growatt/Voltronic/Sunsynk/Megarevo/Victron/SRNE/Solis/MPPsolar/Afore/SOFAR/CHISAGE ESS" I also found in your manual there is some specific configuration for PYLONTECH batteries. So I wonder it may also work with other manufacturers (with some additional configuration?)
@PowmrSolar
Ай бұрын
@@Alexmrg123 Yep, the pylontech protocol.
@Alexmrg123
Ай бұрын
@@PowmrSolar thanks. I guess felicity battery also works via PYL protocol. So should work with PowMr as well. at least it states in their manual: Voltronic/Kodak/RCT/Mecer Axpert and InfiniSolar series communication. 1. Communication Cable Pin: 5,6(Felicity, any port)--3,5(Inverter, BMS port) 2. Setting steps on inverter: Setting→14→PYL. 3. Sign of successful communication: Can check the battery SOC on inverter
@user-ez2jl3or2y
23 күн бұрын
@@PowmrSolarmake a video on connecting the jk bms inverter with the CAN bus
Пікірлер: 31