UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzitem.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.
@joej.4170
7 жыл бұрын
You should have changed the pump oil. Its non-detergent 30W oil. And no you cannot overfill the regular oil in the engine, if its spilling out the top its full, and will continue to spill until its level with the opening. This isnt a lawn mower engine where overfilling will cause it to smoke. Also, use 10w-30 or straight 30 engine oil.
@doubleitp
7 жыл бұрын
Dang... u need to pressure wash the pressure washer after spilling all that excess oil.........
@JG-tk7ov
4 жыл бұрын
trust me dont pressure wash your pressure washer otherwise you'll find yourself here looking at how to fix it like im doing lol
@trukooooo
4 жыл бұрын
You can do that only when is on
@jesussilguero8389
3 жыл бұрын
LMAO
@benderbendingrodriguez2868
3 жыл бұрын
@@JG-tk7ov lmfao
@notyouraveragejohn69
2 жыл бұрын
Is there a tool to extend the drain plug so as to drain the oil in the oil pan only?
@driveheronman4304
10 жыл бұрын
You just put the new air filter down on top of dirt
@tjk6277
7 жыл бұрын
driveheronman That big chunk of dirt probably ended up in the engine. Also, isn't changing the pump oil an important maintenance step???
@punishr36
7 жыл бұрын
Haha saw the same thing. Actually stopped the video to comment. What a hack amateur.
@chadnikkisheppard4937
6 жыл бұрын
haha yeah i was like wtf big chunks of leaves and dirt
@brewsterly2927
5 жыл бұрын
Very poor workmanship. As said above "Love this new generation. No pride in their work." and rush, rush, rush and fuck the engine!!
@RedlineMaximaSE
5 жыл бұрын
Bob Smith At least he’s wearing his safety gear hahaha
@georgebennett785
4 жыл бұрын
spark plug should have had gap checked prior to installation, old plug should have been looked at for how clean it was burning, pump oil should have been checked at the least or drained and replaced. air filter base should have been cleaned prior to new filter installation. draining engine oil, engine should have been tipped slightly to remove as much old oil and you can. this is was more of a SERVICE than a tune up but it was a sloppy service at that
@stevepascal8858
5 жыл бұрын
always great to leave debris and garbage that falls off the OLD air filter and just plunk the new one on top of the garbage. niiiiiice
@cusoonmyfriend3738
3 ай бұрын
yes, what a clown, gonna check another video then thx
@musicfan6575
5 жыл бұрын
I have seen enough after the first Minute.
@jefffitzpatrick388
3 жыл бұрын
Lol. As soon as he started talking about PPE I was out.
@BrockLee3
5 жыл бұрын
"Finger-tight." [Uses ratchet and socket] "Finger-tight." [Uses wrench] You keep using that phrase...I do not think it means what you think it means.
@edwardschmitt5710
4 жыл бұрын
"start with your fingers"...
@noahwhite544
3 жыл бұрын
Inconceivable!
@robertkees6048
3 жыл бұрын
Always be suspicious of anyone that gives you advice that has six fingers on one hand, trust me on this one. Have fun storming the castle.
@BrockLee3
3 жыл бұрын
@@robertkees6048 What about people whomst have six fingers on all three of their hands?
@robertkees6048
3 жыл бұрын
@@BrockLee3 Hey Brock, I'm not very good with math, but that'd be like two fingers per hand, or some combination equaling six wouldn't it. You could have like three fingers on one, two on the other and one on the third, or four fingers on one and one each on the other two; after very little thought, it sounds trustworthy to me. Although it's completely anecdotal my grandfather had three fingers on one hand and he was totally trustworthy. Not only that but he could crush your hand with those three fingers, OK, two fingers and a thumb, but you get the idea, just be careful during handshakes when you see that last combination.
@1745vlad
5 жыл бұрын
I don’t want you even get close to my stuff, after I did see how you doing maintenance....
@paulstephenson2875
2 жыл бұрын
That leaf’s gunna get sucked in first start
@rumsiker
5 жыл бұрын
this guy started wrong all wrong ' 1 you don't use wretched to start spark plug ,2 he never show u or make sure the plug electron gap is adjusted , 3 remove the air filter and not clean the filter canister, 4 messy oil change ,5 did not flush out gas tank and make sure the gas tank fuel line screen is cleaned
@AceVideosOfficial
8 жыл бұрын
Thanks for the info. I own a small business and do not need a big bill for fixing a pressure washer because I was too lazy to tune it up!
@elonpatrick4722
3 жыл бұрын
a trick : you can watch series on kaldroStream. I've been using it for watching all kinds of movies these days.
@davianjoseph5095
3 жыл бұрын
@Elon Patrick yup, I've been watching on kaldrostream for months myself =)
@Fallen2Dope
9 жыл бұрын
you should always tilt it over while draining the oil....
@arlisbartlett403
3 жыл бұрын
Will the engine still stuff be okay?
@JmanRx81
6 жыл бұрын
Get an oil drain tube attachment. You'll thank yourself every time you change the oil. Completely mess free.
@rumsiker
5 жыл бұрын
you can make a funnel like a small shovel out of a flat piece of metal keeping oil away from the wheel and under the motor guiding it down into the pan.
@bamaslamma4965
5 жыл бұрын
Where to start... 1. Change the oil hot, with the pressure washer tilted toward the side of the engine that the plug is being removed from. 2. You can change the plug once the engine has cooled, making sure the gap is exactly what the manufacturer (in this case Honda), specifies. It doesn't hurt to spray a little WD-40 on the threads before installing the plug. 3. When you change the air filter, it makes sense to wipe off the housing base/blowing compressed air (with engine intake covered) to ensure the housing area is perfectly clean. (Homeboy here seems to leave a leaf or a moth sitting on the base, and just puts a new filter right on...) Honda wants you to check the oil level by "not threading" the dipstick plug, but rather-resting it on the top thread...good grief. 4. How about changing the pump oil?
@Tiburnn
2 жыл бұрын
I got a brand new pressure washer..... On the manual its says 600ml but i reach 450 and it spill out? It started first crank but after few hours of using it now it can take like 10 crank before it start......is this cause of the oil? Do i need to put in the 150ml that missing???
@KyeHortonNinjaWindowCleaning
Жыл бұрын
@@Tiburnn there may be 200ml still in the system. Next time keep the engine running a while to warm up the oil which will make it more liquid. Then wherever the drain hole is tilt it as much as you can.
@joebudi5136
11 ай бұрын
I'm here for the pump oil part and ge didn't mention it.
@billbrock2169
4 жыл бұрын
Check the oil level as it’s overflowing hahahahahaahha
@c00cs1
3 жыл бұрын
😂😂😂
@TheBjjninja
3 жыл бұрын
That's Billy Bob level service for ya...always check the dipstick even if oil is bursting through the seams
@beechwood619
5 жыл бұрын
You didn't check the oil in the water pump
@severussnape222
9 жыл бұрын
That is far too much oil, unnecessary cost and can make your engine hard to start you're supposed to go only up to the maximum mark on the dipstick
@Vfh........y
7 жыл бұрын
severussnape222 .....look at the Honda manual. fill it till it flows out and your good. Honda engineers did this for ease of maintaining.
@frankpaul3204
6 жыл бұрын
You should never overfill as he did. The oil level should be on the top of the hatch on the dipstick. Overfilling can cause premature seal wear.
@noeldillon9591
6 жыл бұрын
it's almost impossible to overfill. Any excess flows out before the drain plug is fitted.
@TRUCKMAN399
4 жыл бұрын
Yes just leave it full of water during winter and for good measure drain the oil before use
@Obsurdious
5 жыл бұрын
What about the oil in the pump housing?
@1nice1
5 жыл бұрын
You never change the pump oil, that’s what I wanted to see.
@demolitionbarbiedoll
3 жыл бұрын
Billy wants to see how you flush out the oil tank lol
@catrat1967
5 жыл бұрын
If this is the service department for Russo Power Equipment, do yourself a favor and stay away from them!
@Yamaha200YT
4 жыл бұрын
What about the pump oil?
@handyman8494
7 жыл бұрын
how about a pipe nipple for that oil drain, the next time..
@Ozzie4Para
6 жыл бұрын
Note to self: Don't take my pressure washer in for service with these guys. Good Lord, talk about doing sloppy work....
@DanielCoffey67
2 жыл бұрын
For a revised version of this video in the future, I would suggest showing how to replace the pump inlet filter and also changing the pump oil (15W40 in mine).
@jesussilguero8389
3 жыл бұрын
I think there was another drain screw on the other side of the pressure washer that had a down hole to catch the oil on the pan. Lol but great job made it look EASY and Messy :) thanks for the overall instructions.
@Frank.Gh1968
5 жыл бұрын
you need to open the oil fill cap when you drain the oil from the bottom, otherwise the oil will not drain completely
@daniellang6112
2 жыл бұрын
great point.
@baklash1762
Жыл бұрын
Amen!
@williefufu2985
5 жыл бұрын
I can't thank you enough for this Video. Before watching this Video I didn't know where to start to change the Engine Oil, Air Filter, Pump Non Detergent Oil or to even put in the Pump Saver. I bought a used 3800psi Power Boss Pressure Washer at the Pawn Shop and I followed your instructions. I watched your Video several times, thank you again and God Bless you.
@bharrison1633
7 жыл бұрын
Love this new generation. No pride in their work.
@CharleswoodSpudzyofficial
5 жыл бұрын
Hate this old generation. Full of haters
@antonahill1750
4 жыл бұрын
I agree, seemed like he was rushing through it, thats how mistakes( I saw a lot) are made.
@caleb76553
Жыл бұрын
Russo, do you know what the valve gaps are supposed to be on this particular engine? I can’t find it online and no longer have the correct literature to tell me. Thank you in advance.
@RussoPowerEquipment
Жыл бұрын
Hi Caleb, Valve clearance is .004-.006 on the Honda GX engines
@RussoPowerEquipment
Жыл бұрын
or 0.015 to .020mm
@kchaos23
5 жыл бұрын
You said nothing about changing the pump oil ??
@revup67
3 жыл бұрын
was the gap checked before threading the new spark plug? Out of the box, I've had spark plug gaps be way off.
@davidbradley6165
2 жыл бұрын
please check the fresh oil again and again and again and again and again
@cashman1673
9 жыл бұрын
Way too much oil it should only be at the fill line on the dipstick another thing is you should never use a foldable table as a workbench not sturdy enough especially for something as heavy as a pressure washer and another thing you put the new air filter down on top of dirt clean that out before you put the new air filter in
@metallitech
8 жыл бұрын
It says to use the dip stick without screwing it in at all, so I don't think it's even possible to over fill this engine.
@Vfh........y
7 жыл бұрын
metallitech ....correct......all these comments as off base. Fillet till it flows out and your good. Honda did this for a reason. Job site cement mixers. Easy to service.
@ns671fr
4 жыл бұрын
you keep taking out the oil plug because you know you overfilled it, you're trying to get a little bit out more each time. tilt, your cart slightly more so that oil doesn't get under your engine.
@tyronet.jackson7296
2 жыл бұрын
🤣🤣
@leethburn
5 жыл бұрын
Don’t you check the gap on a new plug?
@patalexander1965
5 жыл бұрын
John Race I guess if it starts and runs, then it’s all ok!
@Itdontmatter69
8 жыл бұрын
For starters take off those gloves geez, oil should never be to the top of the threads, why have xxxx on dip stick then ? And never hold the dip stick upside down either..oil runs up the stick and gives you a false reading, clean up that air filter housing to, and the pump itself?? No oil change ?
@ayotiM
8 жыл бұрын
You mentioned the oil should not be to the top of the threads, at what point do we want it? Thanks
@Itdontmatter69
8 жыл бұрын
+ayotiM fill to the top of the xxxx not above
@Vfh........y
7 жыл бұрын
Mr Plow ......I call bs......2355 hrs on a gx390.....the difference. may be 4 Oz. Now a gx610 has a regular oil stick.
@patalexander1965
5 жыл бұрын
Brian Plow ....and how!
@brianmedeiros417
6 жыл бұрын
W in oil stands for winter, not weight.
@danleehill
6 жыл бұрын
You just put the new air filter down on top of some trash
@Hctoer
3 жыл бұрын
This bothered me too🤣
@AaronNagoo
9 жыл бұрын
What about actual pump maintenance. Not just the motor. For example, troubleshooting or add/changing the oil.
@davidbradley6165
2 жыл бұрын
how do you change the oil in the water pump?
@clintsinger6893
5 жыл бұрын
That was the worst display of how not to do work to any small engine that is out on the internet, buddy you would only be employed for less than a day if you did that sloppy work on my customers machine. you should be ashamed of yourself. the company that you work for should fire you after seeing this type of piss poor work!!!!!
@charlesvassallo4272
2 жыл бұрын
I see you changed the engine oil. What about the pump oil? Should that be changed or checked regularly? I have the 3300psi Simpson
@ao2528
5 жыл бұрын
I was thinking, am I the only one who was surprised by filthy job here? I'm glad I wasn't, after reading couple of comments.
@jayc3631
3 жыл бұрын
How often do we have to change the spark plug?
@scottspooner6070
6 жыл бұрын
If you did that to my engine you wouldn't get paid.
@M70ACARRY
3 жыл бұрын
Drain oil on my equipment like that...Fired!
@leethburn
5 жыл бұрын
I watched this right through and yet haven’t seen how you toone the bloody thing up yet....
@fochoalagos
3 жыл бұрын
Thanks a lot for taking your time and making a great video.
@andregreen8040
4 жыл бұрын
Not only he placed new filter over debris, he didn’t both to check the spark plug gap and that funnel came out of a rubbish bin.
@cameldriver7419
2 жыл бұрын
WHY do you people KEEP ON INSISTING this is a tune up? It is a basic service. Tune up is with the carburetor, mixture and idle screws?
@novaflix1350
2 жыл бұрын
Dam man where'd you learn them oil changing skills from lmao must be self taught, cuz Ive never seen someone dump so much dam oil in a machine to the point it's over flowing and look at it and say: "one way to know you have the proper amount of oil in it is just up to the threads but not over flowing" 🤣😂🤣😂🤣😂 that shit looked like a river coming up out of there lol
@r.a.m.productions1229
2 жыл бұрын
Why is water coming out of my pressure hose with nothing attached? No wand, no ball valve??? It worked fine yesterday.
@baddmaxx25
9 жыл бұрын
last i checked honda used 10w30 not strait 30
@Vfh........y
7 жыл бұрын
baddmaxx25 ......you can use SAE 30 all summer,and they will use less oil. When it gets cold .....switch to 10w30. We run 550 hrs. plus on gx390 and gx610. great engines.
@benstanley4676
4 жыл бұрын
10W30 just meant it changes weight in the winter. if the last number matches the number for the SAE then your good. plus you ain't using the pressure washer below freezing temps anyways
@atozproductions9660
Жыл бұрын
Anybody see that big ass chunk of debris he dropped from the old air filter underneath the new air filter and then secured it in place?... Pepperige Farm saw it...
@AlwaysBeSmart674
2 жыл бұрын
@02.00 you left a giant peace of dirt/debris in the filter housing lol worst tune up ever that could destroy his engine if sucked in.
@craigrogers3163
2 жыл бұрын
How about slow down and get that big chunk of crap that fell inside the intake when you took the old air filter off. Then you just covered it up with the new air filter. Lol
@KaliBlaz
3 жыл бұрын
puts a new spark plug without proper sizing, drops a new air filter on top of dirt, puts oil "unknown" using a dirty funnel... but gloves and glasses come first lol
@douglarboy201
9 жыл бұрын
I have to use one just like this but you left out service of the pump. What kind of oil does it use and how to change it
@Vfh........y
7 жыл бұрын
Ronald Thomas sea 30.....No detergent.
@sheshankutty8552
Жыл бұрын
So he is changing the air filter without clearing/cleaning the dirt on the bottom? Is this clean up or tune up? Tuning is different I thought.
@moisesrobles7884
3 жыл бұрын
Thanks for the info and tips im smashing my like botton kaboooooooooooooom
@coryhagan3336
Жыл бұрын
Checking the oil 3 times is unnecessary. I can see one set of redundant steps to make sure you've done it correctly but three redundant steps is just redundant.
@AJ56
5 ай бұрын
Sloppy work, dirty funnel and didn’t change pump oil.
@AlwaysBeSmart674
2 жыл бұрын
@02:00 you left a giant peace of dirt/debris in the filter housing lol worst tune up ever that could destroy his engine if sucked in.
@johnkishel4152
9 ай бұрын
You don't screw in the oil dipstick to check the oil. You simply stick it in the hole till it stops, then pull it out and check the amount. You are totally wrong to screw in the dipstick.
@jdhappy7663
Жыл бұрын
You never changed the oil on the water pressure motor, or take out the spring and you also didn't clean out the screen on the water inlet where the hose hooks up. Thank you for the tune up info on the Honda motor though
@pierrelabbe3173
Жыл бұрын
Merci Canada
@RussoPowerEquipment
Жыл бұрын
Ne problem pas!
@Mao2187
2 жыл бұрын
You didn’t change pump oil. Which is what I needed to learn this video. 😔
@bigrednick100
2 жыл бұрын
First red flag, no gapping spark plug and no anti-seize and then it just got worse from there
@bjspurgeon1
8 жыл бұрын
Too much oil
@Vfh........y
7 жыл бұрын
bjspurgeon1 ....I've got a gx390 and service the oil like he does 16 years old. 250 to260 hrs per year..also run gx610...but it has a regular. stick....imho
@UnderPressurePowerWashingLLc
5 жыл бұрын
Where did the leaf go ? 🤣🤣🤣
@doubleitp
4 жыл бұрын
Couldnt you hear? The pressure washer was chewing it up for breakfast!
@nickosuperintendant9514
5 ай бұрын
When i opened the oil, it was full of gas. I left the gas overwinter. What should i do now?
@haterzproof
5 жыл бұрын
i wouldn't let you work on my machine but nice try tho
@aldocruz7636
6 жыл бұрын
A cross thread is tight thread
@tonyneville476
Ай бұрын
Why are there 2 oil fill ports? One has black cap other has ivory cap which one is the oil fill?
@LunkerFishing
6 жыл бұрын
I just tuned up two pressure washers this morning. You never gapped the plug unless you did that off camera. I find that prepped plugs are RARELY gapped correctly so you should have pointed out gapping them or at least checking the gap.
@patalexander1965
5 жыл бұрын
Lunker012 If it cranks and runs ok, I guess it’s all ok?
@johhnybgood8413
4 жыл бұрын
How often do you do an oil change and spark plug filter
@joewebb544
7 жыл бұрын
Any person with common sense can tell this guy is not mechanically inclined. Just the part where he slapped a new air filter on without cleaning the trash off and spraying the lube holding the can sideways. That's where I stopped watching. The owner is doing more damage to his company than he could ever imagine.
@davidbradley6165
2 жыл бұрын
don't change the spark plug unless it runs rough or wont start, he took the old air filter off but left debris and dirt in the bottom of the housing. The air filters hardly ever need replacing unless you are working in dusty areas. Why isn't he wearing a motorcycle Helmut as safety equipment also?
@kensetches2276
Жыл бұрын
Ummmm...... wearing gloves when working on an engine aint happening. Get real.
@randomguy2369
2 жыл бұрын
What type of oil should i put in a 2gpi machine gas powered
@kittysch2
6 жыл бұрын
So I learned how to spin a wing nut. Spark plug boot. Loosen oil plug. Get aggressive with a plug. Finger tight/cross threading. Remove fill cap. Don't start without oil. Thank you but ✂ it out.
@iwin4985
Ай бұрын
Did you just do a tune up, or did you winterize the pressure washer,?
@martindurkin5223
2 жыл бұрын
Nice job of leaving all that crap in the air filter housing at 2:04.
@DieConstant
10 жыл бұрын
I didn't know you had to thread the dip stick all the way in to check the oil level. I thought it was intended to be taken out, wiped then just put in without threading and then checked.
@Vfh........y
7 жыл бұрын
Alexis Moreau just fill it to the top.......it's all good.
@brianmedeiros417
6 жыл бұрын
You are not supposed to screw the dipstick in to check the level. This guy knows just enough to get him into trouble.
@JasonY02
2 жыл бұрын
I love the facts you didn't clean the dust out of the airfilter compartment then install the new filter.🤦♂️
@albaestrada6394
4 жыл бұрын
I dont speak English. I need change pull cord Mi-T-M 4000PSI, how ???
@mr.foshow5474
5 жыл бұрын
Can I do the same steps for John Deere ac2700. And I don’t have the manual for you didn’t explain or showed the oil type and where the best place to buy if you can advise me. Thanks great video though
@cherylmorris7318
4 жыл бұрын
I searched this video out to find out how much pump oil to use. I found lots of things with this video that I did not agree with. One was the new spark plug going in. Should never install a spark plug using a socket and wrench. Fingers only to start it. Never mentioned the gap of plug. Why not wash the filter and re-oil rather than replacing and causing more garbage for the environment? Because its all about selling products for list price to the customer, why not just charge for the service of the filter rather than replace? Pump oil should be talked about. I have three books that came with mine years ago, but I cannot for the likes of me find the amount that goes in and should it be tilted slightly forward or all the way forward It says buy pre-measured pump oil, however a lot of people may have efficient oil that would work already in the garage. Like gear oil I was looking for an amount to put in, but no service instructions here.
@m4kingnathan71
7 ай бұрын
What if my fuel is going into my oil in the crankcase?
@mdemory
4 жыл бұрын
what in the fucking fuck dude - do not seek the treasure...
@kpcscience
2 жыл бұрын
Nice overview. Thanks for making!
@darnettda
4 жыл бұрын
This is how to not put in a spark plug... God they let anybody make how to video's..
@sparnt117
9 жыл бұрын
hey I subscribe! do you have a video on how to change the carburetor? if you do can you send link please. thanks
@angelcalderon7845
3 жыл бұрын
Hey at least he’s trying 🤷🏻♂️ a lot of people don’t even do regular maintenance to themselves to be doing maintenance to their cars and PW
@Amazighi-NJ
2 жыл бұрын
bs.. what type of oil you using
@dailydriver7118
7 жыл бұрын
I think you should pull the engine cord while adding the pump saver to make sure each valve assemble gets some.
@maxiuyin5764
Ай бұрын
That's a smart idea, I'm going to try it, though with the exception that in my brand's manual, it says not to pull cord when the spark plug is removed. So I'll try it with it still in.
@rafaels3552
10 жыл бұрын
Very helpful, thanks. I will check out your other videos since I'm a new owner of a gas pressure washer. I don't even know if the water has to be completely drained each time of use.
@gilbertogarcia1477
2 жыл бұрын
You perform the job well, but you need too clean the filter housing before put a new filter on and be a little more cleaner so video look better thanks 👍
@stanleyhenry3700
Жыл бұрын
What about the pump oil? Do we need to replace the oil?
@Brianz613
2 ай бұрын
Great video with excellent detail! Would have liked to see changing the pump oil included as it’s a step a lot of people neglect doing.
Пікірлер: 279