Watched your video at 10:30am and after shopping for parts and installation we were on the water by 5pm. Even made a grocery run during one of my breaks. Thank you for this video!
@Dangdodge
6 жыл бұрын
ApogeeLLC2012 that's awesome glad I could help!
@aaronvennie2132
4 жыл бұрын
Did you have to register your pedal boat
@cynnaolsen633
4 жыл бұрын
How did you stop your boat from leaking underneath where the pedals go in?
@ApogeeLLC2012
4 жыл бұрын
@@aaronvennie2132 We did not
@ApogeeLLC2012
4 жыл бұрын
@@cynnaolsen633 We used all thread and washers thru the same openings. If you send me an email toni@apogeeLLC.net, I'll send you photos. We've never had a problem with it leaking.
@stian222
4 жыл бұрын
How could anyone give this video a thumbs down? There’s nothing wrong with this video.
@jckdnls9292
Жыл бұрын
Cause he didn't use a 55# thrust trolling motor
@se7encapadon
2 ай бұрын
@@jckdnls9292then buy him a 55# thrust motor to put on it🤷🏾♂️👍🏾
@mikea9365
7 ай бұрын
I just found an old pedal boat already missing the pedal drive train. Thanks for making the video and for the great idea! My kid is going to be stoked!
@robertonieves-rios2159
8 жыл бұрын
It's the first time that I see a video so interesting and well done. Soon as I find a used paddle boat, I'm going to make this. Thanks a whole lot.
@amerlee206
7 жыл бұрын
Roberto Nieves-Rios m
@MrGva12886
6 жыл бұрын
Sale you mine
@abdulmananmani4489
2 жыл бұрын
*I bought this model for my 14 ft Jon boat. **enjoyable.fishing** recommend love it!!! It pushes my boat with ease ( 2 men 220 each). I would highly recommend this to anyone.*
@kpete9219
3 жыл бұрын
Dangdodge: Thank you for this video. I converted my paddle boat to electric but I ran into some issues. My boat has a narrower space between the hull and so when I installed the motor, the prop would hit the hull if I turned the trolling motor left or right. I had to set up, using clamps, the trolling motor so I couldn't use it for motoring until it was below the hull or if I had the trolling motor facing straight forward. The clamps work great because when I come to shore, I pull the motor up an fasten the clamp. Also, I used a wood dowel rod instead of steel. Everything else worked fine. It was fun engineering the minor differences between yours and mine but the video was the encouragement to undertake the project. I will be using it on smaller lakes to fish along the shoreline. One other note: I also mounted two oars on the paddle boat using clamps and installed oarlocks. I hope I never have to use them but they are handy just in case the battery goes dead or the motor quits.
@oldwortex5818
3 жыл бұрын
You sir is a genius ! Simple effective and easy to duplicate. Thank you.
@marya4717
Жыл бұрын
Wonderful video but the kids operating the boat be wearing life preservers! Always without exception.
@petem977
5 жыл бұрын
i just wanna say thank you dang dodge !!! every time i go out cruising or fishing it's because of your great video you rock !!!!!!
@bigred6815
6 жыл бұрын
This is a great idea for those who can’t “exercise” very well or can’t use the pedals.
@typeelite9283
11 ай бұрын
This video has my gears spinning! You could take the motor, and attach it to the rear, while at the same time attaching it to the rudder steering pole, while replacing the steering handle with the motors handle. Same thing as this boat, just with rear-motor drive.
@tcsvlogs2667
6 жыл бұрын
Very helpful! Today me and my brother got a paddle boat and a trolling motor so this is something to try!
@tbirdracefan
3 жыл бұрын
I saw this video a long time ago and think it's great! I bought a peddle boat last year for my little pond and its not working out like I expected and now thinking of doing this conversion. One of the problems I have is the hull takes on water thru the paddle shaft unless I sit in the middle seat. I cant see how the threaded rod that replaces the paddle shaft would not be a problem for allowing water in the hull as it does not always stay above the waterline. I am thinking I will just seal off all the shaft holes. thanks for sharing!
@Justinestabrook
8 жыл бұрын
Lol rig mine up. Stupid thing keeps breaking. It was left on the property a few years ago. Now I know why. Loved paddle boating. Good exercise. Just a man made lake behind the house but it's good to sit in the middle of it. The steering broke and I had to drift back to the house. So embarrassing in front of the neighbors lol
@Justinestabrook
8 жыл бұрын
Just kept paddling in circles like a one legged duck
@eddie054
6 жыл бұрын
You should have shot a flare gun into the air for help.
@AddamSantana
5 жыл бұрын
I put a motor on the back, kept the peddles. Put a canopy on it too. All you gotta do is wrap some sheet metal on the back. Plenty strong for a trolling motor. Took five minutes, and have used it several times. You don't have to remove peddles or the rudder! Here's the video. kzitem.info/news/bejne/uIijuaSNiV-KraQ
@socalusc
5 жыл бұрын
show me how please
@mesgs123
4 жыл бұрын
Brilliant brother! GREAT video - I'm going to HD tomorrow to get the parts, etc to do this for my grandkids! Thank you. BTW, I bet if you sold the parts as a kit, you would some real $$$.
@nicksyardcare
4 жыл бұрын
This is a great idea. I will be looking for a pedal boat and doing the same modification on it.
@abousidi75
3 жыл бұрын
Genius and awesome grandpa. God bless.
@hotrodprepper656
6 жыл бұрын
excellent video, thanks for the idea and instructions, I'm in the market for a paddle boat right now.
@jayhall8761
8 жыл бұрын
Defiantly an upgrade! Nice job!
@bigred6815
6 жыл бұрын
Hope this isn’t a dumb thought but is it possible to put the troller on the back and keep the pedals? If so please make a how to video.
@MysticKitty1o1
4 жыл бұрын
me and my dad are gonna try to do this when we get our pedal boat!
@arturopalos2739
Жыл бұрын
Very informative. Thank you!
@hawkdaddy64
2 жыл бұрын
Put a canopy on top with two 100 watt solar panels and have them constant charge the battery/batteries for extended time on water.
@kathyromeo8547
3 жыл бұрын
Amazing!! Will copy at some point in my life!!
@Andy-im3kj
3 жыл бұрын
You are a saint for this video! Thank you!!
@brucewelty7684
6 жыл бұрын
WAY TO GO! outstanding concept and Vid
@ryanmandree
Жыл бұрын
Thank you so much for the video. How does the prop sit below the boat? I am assuming that there is no way for it to be easily taken off every time you take it out of the water, so do you have any tips on how to store and transport it with the prop dangling below?
@roberta.6295
5 жыл бұрын
Nice job! I have a paddle boat I want to put the motor on the back. Im planning on putting the motor right in front of the rudder. Your work is helping me with the part of drilling and adding the floor plate and PVC pipe. Mine will be fixed and the rudder will actually work. Similar as the motorized version of this paddle boat as I have seen pics of where the motor goes. Thanks! By the way what size PVC pipe?
@InfinityVision
3 жыл бұрын
Did you ever build it? I understand if you build it this way (motor fixed in front of the existing rudder like original design) the battery should be placed in front to balance. Also seems like a pain trying to transplant the motor controls up front by the existing steering.
@roberta.6295
3 жыл бұрын
@@InfinityVision I went the easy route as I got a trolling motor from a friend. I mounted a 2x8 piece of wood at the rear as a transom. Clamp on the trolling motor and hook up the battery and off I go! Love it and all so easy too.
@sh3755
3 жыл бұрын
Just did this same setup but with copper pipe through the holes into the 4 way for a cleaner install
@PatTheRiot
7 жыл бұрын
My first thought was Wow, that's neat. Then I figured it would be moronic to remove the entire paddling system to then strap some paddles on the side of this thing just in case the engine dies in the middle of the water for whatever reason. Why not just hook it up in the back and build a homemade arm extension with a steering wheel? Now that would be really something to play with. Not to mention how safer,more powerful and healthy it would be to keep the paddle system.
@AuLily1
5 жыл бұрын
PatTheRiot I was thinking similar. No oars in the boat Incase that event happens, either.
@bethwaller9933
7 жыл бұрын
You are a clever man!
@stantaylor6463
7 жыл бұрын
what did you do with the existing rudder, and what diameter pvc did you use?
@TheRfleming
8 жыл бұрын
Ok that was smart!
@vangkhammeechannel
2 жыл бұрын
Wow that’s so fun video friend I love it.
@fmxinsane
8 жыл бұрын
i need this for coming summer
@asantos3719
8 жыл бұрын
Your one awesome grandpa!
@markburns4777
2 жыл бұрын
Why didn’t you put the pipe through the hole for the pedal shaft? I know it’s offset so the shaft doesn’t hit the rudder steering arm but surely you could have used a slightly shorter downturn to allow a 90 degree elbow setup. I feel like there must have been something else preventing you from doing it this way since you designed a nice setup.
@DonALofts
3 жыл бұрын
Since it is now motorized do you have to get it registered?
@freescreech7392
5 жыл бұрын
Would be easier to just snap a pic of where the wires were attached instead of writing it
@MrDirtysteve75
4 жыл бұрын
Do what works for you. Drawing wasnt exactly hard.
@davida.simpson7011
5 жыл бұрын
Great Vid, much appreciated!
@anthonydecamp3126
3 жыл бұрын
Downfall in order to go forward to trolling motor has to be in reverse another thing way too much PVC but the trolling motor on the back of the get rid of the rudders and the thanks and everything the trolling motor you want do use needs to have feet pedals so you can control the speed with your feet and not your the same bar that turned your rudder you can now hook up to the trolling motor and use that to turn the doing it this way you will get a tighter turn with the boat plus having the shaft where it can't move like that if you hit a stump destroy your motor
@carlosnadal1
8 жыл бұрын
How do you seal for water leaks?
@tylerbonser7686
3 жыл бұрын
Flex seal
@lionelsun425
5 жыл бұрын
Excellent. Can you let me know which motor you use. I want to make sure that we can follow the exact same procedure. Many thanks
@montiemichel2277
4 жыл бұрын
Did he answer this question?
@fangorn1000
8 жыл бұрын
very smart way. thank you for sharing.
@bigred6815
6 жыл бұрын
I don’t mean to ask a dumb question but is it possible to have the pedals and the motor feature so a person operating the boat can alternate? Also thanks for explaining everything so well. Are you in the teaching profession?
@davida.simpson7011
5 жыл бұрын
You can but the paddle wheel will turn as the trolling motor pushes you along. The pedals will also turn so you either have to position your feet out of the way or pedal along with it. Also slows you down quite a bit. Aquacycle makes an electric motor kit designed for paddle boats that looks pretty nifty but it cost over $2,000.
@se7encapadon
2 ай бұрын
What is that clamp called that you used at the end to pull motor up out the water and lower?
@sunshine13emu
4 жыл бұрын
You are brilliant! Thank you!!!
@mirriulahwaterdog
6 жыл бұрын
Gday mate... thanks for the video... Q. does the motor have to be lowered in order for it to give propulsion or will it work in the raised position. I ask this because I want to use my paddle boat in fairly shallow water holes to set and retrieve yabbie traps and it would be good to have not too much extending below the hull.
@jadeddragon4254
Жыл бұрын
It's great......until you hit a patch of weeds. Impossible to clear the prop unless you like swimming
@WisdomOfNivak
3 жыл бұрын
I'm curious about leakage from where the peddles fed through... or am I not understanding the physics of a pedal boat?
@emiliomayosr.8253
11 ай бұрын
Great video
@lorimckellar2801
5 жыл бұрын
What an ingeniously awesome idea!!! U R the man!!! Just seen a free paddle boat on Craigslist, it has a broken paddle, and wallah, I found U!!! Hope it's s5ill available, lol.. I'll B back(in my fake ass Arnold voice, lol🤣🤣🤣🤣🤣🤣🤣
@dmudder5529
6 жыл бұрын
Well done, thanks for posting.
@mainehypnosisllc3294
2 жыл бұрын
Can you please tell me what size motor I need to get for a 3 -4 person one? THANKS!
@jameswillis1742
5 жыл бұрын
I wanna do the same to my paddle boat however you did not mention any measurements for the mounting plate up top, the length and i.d. if the shaft and how you secure the lower end of the shaft to the bottom end of the boat plus how you removed the paddle wheel you mentioned it was easy however i may not have the same boat i think mine is a sun dolphin...any help would be appreciated from anyone who had done this thank you : )
@user-sz7fo1jm1w
Жыл бұрын
Runs good but you need a battery that’s a little bigger than they say
@Luckelux
7 ай бұрын
So how long does the battery stay charged using the electric motor ?
@Ocalagirl7878
3 жыл бұрын
Trying this! Can you say amazing!
@willsmiffsbackhand8517
9 жыл бұрын
Thanks for making this video.does the pvc for the shaft go completely through the boat? Or just a small length on the top and bottom.thanks
@Dangdodge
9 жыл бұрын
Thanks for watching. The PVC that the shaft goes through is about 10 inches long. It goes from the metal floor mount that was screwed to the top of the boat down to the tee that is at the bottom. If you have any other questions feel free to ask.
@cordieray2471
4 жыл бұрын
How long was the medal rod he (you, they. et.al) installed? Yes. i know it may vary with boat, still?
@hugoforget2069
6 жыл бұрын
Please can you give the plactic tube diameter en steel bracket. Tks
@MrDirtysteve75
4 жыл бұрын
Just get a piece of pvc that a little bigger than your shaft.
@OOICU812
8 жыл бұрын
You might want to carry a spare battery or a set of paddles. Just saying.
@amerlee206
7 жыл бұрын
LES
@jeffsc9440
6 жыл бұрын
It would go for hours on that battery pushing a 16 foot boat...I think they're fine
@anthonysanchez9746
7 жыл бұрын
Great Video!
@FaTBoYEtHaN
7 жыл бұрын
I did this and its awesome. go fishing all the time with one of my buddies. The only question I have is do I need to get the boat registered now since it has a motor? Im in Washington. Otherwise I will just say I didnt know lol
@Donna-vh5ym
6 жыл бұрын
ShaftDrafter97 // no registration needed.
@MrTlave1
8 жыл бұрын
hello. I'm in the process of converting my paddle boat the same way. (Thank you for the idea). Do you have any problems with steering it? I want to make sure it works the way I need it to. Thank you in advance.
@realmetis8002
7 жыл бұрын
always wear your life preserver PS i know from experience
@martiwf0
6 жыл бұрын
Love it. I will build one today
@Chazfunaccount
7 жыл бұрын
Can you post the schematics and measurements for your instructional video please?
@davidkettell6236
5 ай бұрын
You neede to put a bilge pump in their ,my paddle boat fills up with water every time i put it in the water .lol.
@glenntorrico
9 жыл бұрын
Thanks for the great post. Is that a 30 inch, 36 inch or other length shaft?
@amerlee206
7 жыл бұрын
Glenn Alan Torrico o
@tylerbonser7686
3 жыл бұрын
A bit more practical than mounting it on the back.
@TEAMKIRK22
Жыл бұрын
Genius!
@sighck
3 жыл бұрын
nice yankee ingenuity
@ashleymillhouse6289
Жыл бұрын
What thrust is it?
@silentmajority5657
7 жыл бұрын
That was a great idea. ty
@russellmartin469
2 жыл бұрын
What size shaft is the trolling motor 30 in ?
@michaelmckenna9022
Жыл бұрын
Why not leave the pedals for when the battery dies.
@johnquinn5581
2 жыл бұрын
What pound thrust motor did you use ?
@peeinginthewind
4 жыл бұрын
How many pounds thrust on that unit ?
@AmberPierce-c5f
2 ай бұрын
Where's how to take off the paddles 😭 I need that video and can't find it
@nataliereyes132
5 жыл бұрын
This is awesome thanks
@ktmexplorations
4 жыл бұрын
awesome for fishing
@wendyb9923
6 жыл бұрын
put a hole through the boat? wont water get in the boat and sink it?
@robertroigsantamaria
4 жыл бұрын
it will not... as long as it is not below the water line....
@sbetts10001
4 жыл бұрын
I did exactly as u did and my paddle boat wants to go forward at a 45 and go around in circles. Thoughts?
@chrissnider9555
4 жыл бұрын
Sounds like the tiller/handle and the motor arent lined up with each other
@mrhoya14
6 жыл бұрын
How fast does it go with that trolling motor
@goresaenz6736
8 жыл бұрын
What size was the floor mount and fittings?
@cynnaolsen633
4 жыл бұрын
Did anyone have any trouble with there boat taking on water from underneath where the pedals come out? I have the boat and motor ready now
@MishinFishin
6 жыл бұрын
What make paddle boat is that ???
@Diana-wg1tm
7 жыл бұрын
Don't you have to register the boat now since it has a motor? I love your idea
@kimmyroze8578
5 жыл бұрын
Usually only gas motors.
@craigostapowich3864
4 жыл бұрын
It has to be over 10 hp
@voltron63
8 жыл бұрын
cool think man....
@MishinFishin
8 жыл бұрын
What size pvc pipe did you use ???
@annabellecaissie992
5 жыл бұрын
Just by a small boat and put a motor on much easier.
@m.sggs_9789
7 жыл бұрын
@dangdodge great how to video
@skynet7078
7 жыл бұрын
wow..nice. can I borrow to fishing?...
@teshuvahemmet3036
Жыл бұрын
👍🙏
@brandonwright2067
6 жыл бұрын
Like it alot
@jackyAmar13
5 жыл бұрын
what about some solar panel for juice...
@justuschmiii3173
3 жыл бұрын
Geee, TNX 4 NOT giving specific items, diameters, width, height, links
@carolerhacheleblanc3950
5 жыл бұрын
Ya very smart! 2 kids with no floating vest!
@thegarage161
5 жыл бұрын
Yeah cuz there's a little thing called swimming!!! most people who live by the water know how to do it!!!!!
@carolerhacheleblanc3950
5 жыл бұрын
WOW! That answer is the reason why kids drown every year. Happy swimming!
Пікірлер: 156