Back in the day a schematic was seldom needed. Most problems were tube based and with block diagram knowledge and a simple tube tester a tech could fix 95% of radios. The same was true with TV servicing, I learned radio electronics on that very RCA radio you have on your bench,, however before I got to that stage I studied basic electronics. My years of experience and advanced knowledge grew from each set I worked on, learning about test equipment was another part of the courses I took at RCA Institutes in NYC. These days the problems that occur are mostly component based due to aging of the radio receivers. Yes today a schematic is much needed.with experience and practice expertise is finely developed.
@emanuelmifsud6754
Жыл бұрын
As myself, an Electronics teacher, I found you to be comprehensive, informative and accurate. Great video. Thank you.
@iainportalupi
Жыл бұрын
Thanks!
@bobdurk5180
3 жыл бұрын
I have read through radio schematics in the past with some difficulty, this was a very helpful tutorial. I was able to pick up some new knowledge thanks to your step by step description.
@pinballpsycho
Жыл бұрын
Outstanding overview! Thank you very much.
@iainportalupi
24 күн бұрын
@@pinballpsycho thanks!
@HiTadpole
4 жыл бұрын
So far this was the best video of this kind out there. This was very good and really helped. I would like to see you expand on this topic especially things like voltage in and out of tubes, current flow, and using a multimeter, etc.
@iainportalupi
4 жыл бұрын
Arpie S thanks! Those are good video ideas. I’ve got a couple videos in the works in the works and then I will get on them.
@Stumpbeefknob
2 жыл бұрын
Thank you. Excellent explanation
@HL-oo9ch
3 жыл бұрын
Very comprehensive and helpful, thank you so much. Taking my first dive into antique radio restoration and it's people like you who make it possible
@richardthomas9263
4 ай бұрын
I found this very informative, especially the parts about changes on the schematic and also other differences in what something was called then vs now.
@iainportalupi
4 ай бұрын
Thanks, glad I could help!
@anthomurray
2 жыл бұрын
As someone just getting into the world of radio restoration late in life, this made me very comfortable looking at schematics. After watching this video, which I will watch again, I find looking at schematics less intimidating. Thanks!
@markusallport1276
4 ай бұрын
A few things that are now clear to me that I find are eye opening. This is a very good lesson I couldn't be thankful for, thank you. #1 I didn't know that the tube layout isn't the same on some of these schematics, I should always reference the actual tube layout, not the drawing to locate the pin-outs of the tubes. I always assumed the pin-outs always went from left to right in order. Now I know this is not true. Not being trained in schematics, I am self taught and I assumed many things, but the biggest assumption was the tube layout in the schematic. #2 the addition of the supplemental circuit on the schematic. I now know this is where I find the different version of a certain part of a circuit, where before I always thought it was on the drawing as an option. (Yes that may sound silly, but to an untrained person, this is the only thought process I had to account for that addition in the schematic.) A great lesson for me to keep in mind from now on. Also, I can now go back to some of these old radios I have set aside, because I've been having issues with, and correct my mistakes. Thank you.
@iainportalupi
4 ай бұрын
Glad I could help!
@robertdiffin9136
2 жыл бұрын
Just found your site…just (at age 66) getting into this hobby since grade school Heathkit builds. This is a great video! Thank you for making this, I know the time and effort involved. I know there is no reward in this save the immense appreciation from your “students”. Please keep creating.
@Ticker2
2 жыл бұрын
Iain, just wanted to stop in and say thank you. This video was great. Luckily it was one of the first ones on this subject that I watched and it out down a great foundation of knowledge to build on. Thank you.
@iainportalupi
2 жыл бұрын
Thanks! Glad I could help.
@reportingfromthebunker
2 жыл бұрын
Thank You iain from London. you have enlightened me on so many of the oft overlooked basics of reading schematics.
@johnmcgaghey1127
Жыл бұрын
Thank you for the excellent video. This was very helpful.
@davidabineri908
4 жыл бұрын
Well done Ian, very interesting approach to schematics. Keep you interesting topics coming! Very good explanation!
@iainportalupi
4 жыл бұрын
David Abineri thanks, there’s more on the way!
@Kinglota
Жыл бұрын
Found this video looking for how the loop antenna should be attached on an abused 1X, stayed through the whole thing! Wish I could send it back in time to when I started doing radio restorations, possibly the best explanation of schematics and how to map them to the circuits they represent, neither too technical or too simplistic; would have saved me a lot of frustration. Thanks!
@gr575
2 жыл бұрын
Great video. Good quick high level summary of how to read tube schematics and what the sections do. I've read hundreds of schematics over my career and Iain is clearly very knowledgable. I have zero corrections for this well done video. I watched it at 1.7X - that was the perfect speed for me. At 1X it's too slow.
@justinmason435
2 жыл бұрын
Ian you have the best by far of any videos on here teaching how to read these old schematics. Please keep it up. I subscribed and got all notifications bro. Please please keep it up. You just helped me fix my Johnson. Messenger Two Cb radio. 🤘🏻
@iainportalupi
2 жыл бұрын
Thanks, I’ve got a bunch of radio videos planned for this winter.
@kennethiman2691
3 жыл бұрын
One of the most concise and understandable videos ever. Top notch job!
@iainportalupi
3 жыл бұрын
Thanks!
@michaelszczys8316
2 жыл бұрын
Good explaining. With my very limited electronic knowledge I was able to follow along knowing a lot of it while seeing a few things in a new light. I have a 1934 Philco that I have had since a small child over 60 years ago. It should be pretty much untouched and I am getting slowly geared up to go over and change capacitors before trying to play it anymore.
@stellarpod
4 ай бұрын
I know I'm late to the party (as usual), but this is BY FAR the most helpful, useful explanation of a radio schematic I've ever watched. Extremely well done, sir! I've got an old Zenith console 8-S-463 (5808) that I hope to try some restoration on. As always, thanks so much for sharing. Steve
@iainportalupi
4 ай бұрын
Thanks!
@loricastro3772
2 жыл бұрын
First time on the channel and I loved this class, subscribed! Thanks a lot you for sharing.
@davidmills5940
2 жыл бұрын
Thanks for a really solid description.
@mattp.6024
3 жыл бұрын
Very nice job, Iain.
@andrewblack4100
10 ай бұрын
Great approach, very well explained. Well done, Iain - thanks very much for sharing your expertise with us.
@thebuggy736
5 ай бұрын
You can download a RCA Receiving Tube Manual as a pdf. There is a lot of good information in this clip. About the AVC (- 13V max) is related to the amplitude of the carrier wave. The carrier is rectified and smooth to a dc voltage. Strong signal high AVC voltage, less amplification. Weak signal low AVC votage, higher amplification. Please correct me if I am wrong. The voltages given in the diagrams are messured with an analog multimeter specified in the diagram very often around 20kOhm/V. Today we use digital multimeters. No problem but the voltages can differ a bit. I think with the comments we make it a nearly complete good guide to read valve (tube USA) diagrams.
@radiobenchly1828
4 жыл бұрын
I agree with the others. This is easily one of the best vids on getting to know schematics, and definitely something every beginner should watch. Great work, Iain!
@patrickmcmurray9446
8 ай бұрын
lain you are an excellent teacher! This layman now has hope to work on my 1937 Western Radio Patrol model 76. I noticed you never say "uh, um, hmmm" or the like as space filler. You wait for the right word. Again, excellent! Thank you for this top video.
@iainportalupi
8 ай бұрын
Thanks!
@jamesbowles2486
3 ай бұрын
Wow this is absolutely awesome. I just got and old radio and had no clue where to start thank you so much for posting this
@mogulsmoke2428
3 жыл бұрын
I really appreciate this video. It answered so many questions for me as a beginner. THANK YOU...especially how to know when to use which capacitor. Thanks again
@mogulsmoke2428
3 жыл бұрын
PS, I ordered the tube book while watching the video... I now see why I need it.
@smig72
Жыл бұрын
As someone new to this hobby I would like to thank you for your good explanation
@iainportalupi
Жыл бұрын
My pleasure.
@ope-aaron
3 жыл бұрын
I wish I was able to watch this video 3 years ago. It should be helpful with the new one I just bought though! Thank you!
@throsturv
4 ай бұрын
Great video Iain! Tanks, Throstur. 😊
@lionelpostwartrains
3 жыл бұрын
Best explanation I have seen yet. Keep up your instruction videos please.
@nextacuityandnextphoto155
3 жыл бұрын
Your an excellent teacher, I saved this link as it was really helpful.
@iainportalupi
3 жыл бұрын
Thanks, I’m glad I could help.
@thomasrice2888
3 жыл бұрын
The best explanation I have seen yet! Thanks!
@shyammohabir8283
3 жыл бұрын
Very Good Job explaining the radio circuit!
@kwacz
Жыл бұрын
very good informative video. thank you. I like to use the term kilocycles when working on old stuff because that's how they said it back in the day. I use the term kilohertz when working on new things because thats how it is said now (when the item was made). I do this just because it drives people nuts but I am also being period specific at the same time so you cant really get mad.
@billdau
3 жыл бұрын
OUTSTANDING video! Best explanation I’ve seen. Thank you!
@iainportalupi
3 жыл бұрын
Thanks!
@vicktor440
2 жыл бұрын
Very good young man .Really learned a lot..Thanks
@djbishop30189
3 жыл бұрын
Very thorough and detailed explanation. Thank you!
@iainportalupi
3 жыл бұрын
Glad you liked it!
@johnrieger2461
3 жыл бұрын
Very well done and helpful. can you suggest were to purchase parts. i just retired and have a collection of old tube radios that i would love to get working again. Looking forward to future video's. Thanks again..
@screech1991
3 жыл бұрын
I've just started too, but mouser and digikey are great websites for things like capacitors and other electronic components. No minimum order and a wide selection
@F1FanWoodsie28
4 жыл бұрын
This was super helpful as I'm starting repairs on an old Montgomery Ward's Airline radio! I looked back and forth between the schematic and the radio for quite a while and still couldn't make sense of everything, but this really helped clear it up, so thank you. I'm still not entirely sure how to make sense of all of the lines and dots and where they come together vs. where they meet at a tube's terminal (that doesn't seem consistent on my radio), but it may be worth a try!
@iainportalupi
4 жыл бұрын
F1FanWoodsie28 one thing to remember is that many times the manufacturer attaches the components to what ever the handiest place is under the chassis. Lets say a schematic shows a 1 ohm resistor and the B+ voltage connected to the plate of tube number 2 on the schematic. Now the B+ also connects to the plate of tube number 4. In the radio the manufacturer could have connected the 1 ohm resistor to the plate of tube 4 because the resistor couldn’t reach tube number 2. The schematic is still correct because since the pate of tubes 2 and 4 are connected together so even though the schematic shows the resistor connected to 2 and in real life it’s connected to 4 electrically it is the same thing. They drew the schematic in a way the keeps any one section from getting too crowded looking while in real life they assembled the circuit however they could to use as few wires and tie points as possible. It is confusing but after a while you get used to things being electrically like the schematic yet the physical construction is not laid out like it shows in the schematic. Sometimes it’s just a big game of connect the dots. I hope this explanation helps.
@F1FanWoodsie28
4 жыл бұрын
@@iainportalupi As an update, I'm happy to report that after replacing nearly everything, the radio I was redoing now works! Thank you for the tips!
@iainportalupi
4 жыл бұрын
F1FanWoodsie28 that’s great news!
@defytyrantsofmississippi2198
3 жыл бұрын
Awesome video! You are a master at teaching this stuff. I really learned a lot. I was wondering if you were going to do a video in the near future explaining the basic concept of the superheterodyne receiver? I’m still trying to wrap my mind around the concept of mixing signals to get an intermediate frequency. I would really like your explanation being that you teach these things so well. Thanks
@janbill79
9 ай бұрын
very nice of you to explain all this! thks
@iainportalupi
9 ай бұрын
Thanks!
@ralphmilner3347
Жыл бұрын
Excellent job walking through the schematic Lain. Thank you.
@mikekarpaty3871
5 ай бұрын
Very interesting and consise. Now I have a much better idea of what's going on. Thank you Ian,its much appreciated 😊
@iainportalupi
5 ай бұрын
Glad I could help!
@anthonykinrade8642
3 жыл бұрын
Excellent video, thanks.
@iainportalupi
3 жыл бұрын
Thanks!
@conwaynoel3715
2 жыл бұрын
Very helpful vid , thank you.
@dennisbeauchamp6193
3 жыл бұрын
great video! thanks for taking the time to explain.
@bigdumbguy
Жыл бұрын
Great job. Thank you.
@carltrummer9103
3 жыл бұрын
Thanks a lot for your very instructive video.
@tedspillers2252
2 жыл бұрын
Very well done! I have learned a lot! Thank you!
@iainportalupi
2 жыл бұрын
Thanks!
@briankays2635
2 жыл бұрын
Dude - freaking BRILLIANT!!! THANK YOU!!!
@indioflechudo6221
3 жыл бұрын
Excellent video. thanks.
@peskycat
3 жыл бұрын
Well done. Thanks!
@iainportalupi
3 жыл бұрын
Thanks for watching!
@drgrahambeards9776
24 күн бұрын
Highly informative, thank you
@iainportalupi
24 күн бұрын
@@drgrahambeards9776 glad you liked it!
@jimmiddleton5093
3 жыл бұрын
Excellent video 👍 Very well done.
@vtradio
3 жыл бұрын
Thank you. This helped me out a lot. Paul AA1SU
@mikeerstad3705
11 ай бұрын
Much Appreciated video.... Thanks Iain...
@alexblizzard9113
11 ай бұрын
Good work, this has helped me a lot. Thanks.
@hinspect
10 ай бұрын
I went to Tennessee Institute Of Electronics in 1979. All of the schematics back then were "Sams Photofact". I haven't watched your Video to the end yet but it looks great! I was lucky to get employment while still in that school from an AM/FM Radio Station and my supervisor/chief Engineer was an electronics instructor. I assume Sams books are still available?
@gabevee3
4 жыл бұрын
Pin output for the converter, you can easily swap 2 and 7 since they're the heater and the pins will be exactly 1-8 clockwise. Yes, many times they do not put the pin outs exactly but when they use the image as in this schematic, it most likely will be exactly correct pin outs starting with the notch on top, counting 1 to the immediate right clockwise to 8. ;-)
@iainportalupi
4 жыл бұрын
gabevee3 I see you caught that. I swapped those pin numbers to make a point because this schematic really did have the pins in the correct order but I was trying to get people to not assume they always were in order.
@gabevee3
4 жыл бұрын
@@iainportalupi Understood. Terrific video BTW. Two thumbs up! :-)
@dicko-200
10 ай бұрын
S1 needs to be moved to the hot lead not ground, with a polarized plug. Very nice class, thank you.
@colonelgigi
Жыл бұрын
Good job ! 👍😎👍
@nelsonfernandes3929
Жыл бұрын
VERY HELPFUL THANK YOU
@waynejohnson8712
3 жыл бұрын
Thanks, lain. I learned a lot.
@Timothycan
Жыл бұрын
A very good introduction into reading vintage schematics. Just one thing to note: Some very early schematics used M for 1,000 when referring to resistors. We are more used to seeing the letter K used for this, so a 3k resistor is 3,000 Ohms. But some old schematics might show resistors as being, say, 220M. That is NOT 220 Meg Ohms! That would be a ridiculously high value, in fact it would almost certainly mean 220k, or 220,000 Ohms in modern parlance. Just another one to look out for.
@rgraham9792
3 жыл бұрын
Thank you for this! Very helpful !
@iainportalupi
3 жыл бұрын
R Graham glad you liked it! Thanks for watching.
@diydan6045
3 жыл бұрын
Thank you for posting excellent explanation.I just bought my first radio a Zenith 5d320 1937, I'm going through replacing capacitors and verifying resistors. But I noticed the schematic shows two R1 resistors and 2 C4 capacitors. Have you seen this,?
@iainportalupi
3 жыл бұрын
That’s a new one to me, I’ve never seen duplicate part numbers on a schematic before. Where did you find the schematic?
@diydan6045
3 жыл бұрын
@@iainportalupi can I send you a picture? I got one from radio museum.org and another one from nostalgia air both the same schematic.
@justinmason435
2 жыл бұрын
Bro best vids ever
@cameronburns4187
3 жыл бұрын
Very good video. I learned a lot from this. One question...what is the difference between chassis ground and regular ground, and how does that present when you are looking at the radio?
@m.alig.5126
23 күн бұрын
agradecido con tu explicasión, un saludo y agradecimiento
@dean-543
Жыл бұрын
This is awesome.
@iainportalupi
Жыл бұрын
Thanks!
@dean-543
Жыл бұрын
@@iainportalupi please keep making these, I recently became interested in this stuff and it’s really cool.
@kenl2861
4 жыл бұрын
That was VERY helpful! Thank you!
@greggsvintageworkshop8974
4 жыл бұрын
What a very good explanation Ian. Very well done, if you are not already, you would make an excellent teacher. So in my experience most of the schematics I've read vary dramatically as far as information provided. Unfortunately most have no voltages shown and occassionally no ohms for coils. Also, on really old ones the resistance for resistors can be represented by the letter M vs. the letter K for thousand, and meg for megaohm. The rake being chassis ground and the inverted lines being circuit ground, if a schematic has no brakes and all inverted lines, are those now chassis grounds or are they all still circuit grounds and no grounds to chassis? Excellent video!
@lengle73
4 жыл бұрын
Thanks for the video, very helpful!
@iainportalupi
4 жыл бұрын
lengle73 I’m glad it was helpful, thanks for watching!
@indioflechudo6221
3 жыл бұрын
Good video, I'M working on a Hallicrafter S20R,and I find so many things that don't match the diagram; But this radio looks 100% original every component is from that era. but I chase components on the diagram but too many are not on the radio...is Crazy.
@iainportalupi
3 жыл бұрын
I’ve found that sometimes the manufacturers make changes to the circuit throughout the production run and the updated schematics got lost over the years. I’ve got a couple Yaesu FT 101 radios and they are famous for having parts appear and disappear throughout their run. I have three different schematics for the FT 101e and they are all slightly different. The thing to remember is the manufacturer only truly cares about manufacturing the radio. They make a design change and may or may not update their records to reflect it.
@indioflechudo6221
3 жыл бұрын
@@iainportalupi yea that must be what it is.
@Chondrule
Жыл бұрын
Well done!
@kristhompson8112
Жыл бұрын
I learned something today
@jimburns348
2 жыл бұрын
You got the C1 C2 backwards. The curved arrow is the tuning cap. The other is the trimmer.
@TubeRadioRepairRestoration
4 ай бұрын
On 12sa7 are you sure the heaters are numbered correctly? If you switch 2 and 7 they do go around in order
@arielinoa9161
6 ай бұрын
can you make a video going over the cobra 25gtl schematic?
@user-nh7uz8xo1t
7 ай бұрын
Thank you
@natasaparasiri5985
3 ай бұрын
Any chance for chematics for a Tesla radio T 505-u?
@janbill79
2 жыл бұрын
ditto, to the praise everyone else gives. very nice job. So I see, the two in each can, and on other vidios where the take a can apart & put two capacitors in there. now i know the reason. and some people put 2 seperate, & then leave them under neath is that right? thks again
@endo2th
Жыл бұрын
Thos was really good!
@madjack8893
3 жыл бұрын
New sub ☘️
@joseayllon7599
3 жыл бұрын
Hello, I'm trying to get an schematic in English for a Telefunken Jubilate 1161 radio. Can you help me ?
@tubeDude48
10 ай бұрын
Also see: *Jim Burns* He does full restorations
@kutectar
3 жыл бұрын
Hi there can you teach me how to read schematics and radio repair
@jeeplvr2000
3 жыл бұрын
This is fine if you have a decent schematic. My schematic is straight from the riders manual and Is quite terrible, and has Typo's. I can read most schematics relatively well but this one is bizarre. Riders volume 12 sears and roebuck chassis 110.400.
Пікірлер: 133