Happy that the new kit worked out. It will be nice to have the tractor running again.
@PlanetMojo
3 жыл бұрын
I sure hope so! I still have some lights and other stuff, but that's for a rainy day. 😊
@georgesabol459
Жыл бұрын
Finished one just 2 days ago. I was selling a Wisconsin agnd. I always test everything before sale. I was an idiot and left fuel in it for God knows how long. Sprayed carb cleaner to prime it , hit on the first crank [ as always ] did before. Ran for a second or two. Took the carburetor apart, found the float completely dissolved. I pulled an old kit off the shelf, it was a Teledyne repair kit. I had 1 original float left. Completely went through it, didn't soak as long as this video, reassembled it, put it on, off to the races. Quick note, never soak carburetor in gasoline. Remember, that's the very thing that plugged it up in the first place. Always remove Welch plugs too. Take care in setting float level. This engine is an absolute monster. Sold locally for a tidy sum. An old engine that was made to run all day everyday!!!
@PlanetMojo
3 жыл бұрын
This Marvel Schebler carb is finally done! I have pruning to do in the vineyard the next few days (weather permitting), then the forecast is calling for three days of rain. Hopefully I can get this carb on the tractor and attempt to start the thing then. It will be nice to have it running - and out of the machine shed! 😊
@drue4574
3 жыл бұрын
Oh my gosh, it's going to run better than it ever did!
@PlanetMojo
3 жыл бұрын
One would hope so 😉
@zach3619
Жыл бұрын
My Steiner carb rebuild kit for my John Deere is on its way. Hoping it works out well for me 👍 thanks for the vid… never rebuilt a carb before and am excited to try it out.
@PlanetMojo
Жыл бұрын
Thanks Zach, and good luck! 🤞
@drue9901
3 жыл бұрын
Looking forward to seeing that tractor do some work around your homestead. :-)
@PlanetMojo
3 жыл бұрын
And get it out of my way in the shed - don't forget about that 😉
@mikeburke8656
2 жыл бұрын
Love the idea of using the 1/4 drill bit. I used a metal ruler and it was hard to get a good measurement. I also like your rebuild base, roll of tape.😀
@PlanetMojo
2 жыл бұрын
Thanks Mike!
@snkboarder
7 ай бұрын
Rulers can be hard. I've got a micrometer that's more precise.
@bobe8868
Ай бұрын
I got a kit from SpareX and it told me to use the old Nozzle, but did have a new one in the kit. I have found a wide tip screwdriver is not needed to remove the main seat. Use a long thin screwdriver or your butter knife and lay it in the seat groves horizontally and turn it out.
@wackowacko8931
Жыл бұрын
Right there at the end where you are putting the choke butterfly on the shaft - it's nice that you made a tool to lift up the flap on the choke butterfly, but it isn't needed. On the lower carburetor base, on top of the base you'll see a slot right behind where the choke shaft goes through. Once you start the butterfly on the shaft, stick a slender screwdriver down that slot. It will lift up that flap on the butterfly and allow you to slide it the rest of the way on the shaft. It's also why you should put the choke in before you bolt the top (aka airhorn) onto the carb base.
@adenvet2830
3 жыл бұрын
Hi Mojo, great vid and between all the parts you got there, let's hope you don't have disassemble it again and it starts right up, look forward to hearing it purr, talking of purr how's the kitten, did she make it, hope so
@PlanetMojo
3 жыл бұрын
Unfortunately, the kitten did not make it, but the tractor will purr like a kitten nonetheless! The next rain day I'm going to give it a shot!
@williamT9325
7 ай бұрын
Great video
@PlanetMojo
7 ай бұрын
Thank you William!
@SamlonHoldfield
3 жыл бұрын
Suspense builds... :)
@PlanetMojo
3 жыл бұрын
I know, and I wish it weren't. If this thing don't start... 😠!!!
@SamlonHoldfield
3 жыл бұрын
@@PlanetMojo Yeah, but what are the odds?! 😉
@PlanetMojo
3 жыл бұрын
@@SamlonHoldfield I think it's like 90/10 that it starts... but I may have jinxed myself right there 😉
@SamlonHoldfield
3 жыл бұрын
@@PlanetMojo lol 🤞
@carsonwood4663
22 күн бұрын
Did you end up having any problems with the packing on the choke shaft leaking? Just seems like the felt ring isn’t a very good seal?
@snkboarder
7 ай бұрын
That's where the dang pin goes.
@PlanetMojo
7 ай бұрын
Dang pin goes there. Gotcha.
@wilbertfilcek5901
4 ай бұрын
Just wondering why people rebuild carb for same price as new one
@TheFreddy199
Жыл бұрын
Do you know what size that screw plug is by chance?
@PlanetMojo
Жыл бұрын
No, I do not. Sorry 😐
@alaxandersupertramp6955
Жыл бұрын
what did that carb come offof.thanks
@PlanetMojo
Жыл бұрын
TO-20 Tractor
@mattsebenoler9283
11 ай бұрын
You ordered the wrong kit from Steiner. That’s why you have two jets. It may work, but maybe not.
@coleyeomans5219
3 жыл бұрын
That thing is taking forever
@alaxandersupertramp6955
Жыл бұрын
$32.08 new carb on ebay, why rebuild??
@PlanetMojo
Жыл бұрын
Chinese Ebay carbs are junk.
@snkboarder
7 ай бұрын
A real, actually rebuilt carb is $300 plus. I've used Chinese carbs for B and S lawn mowers for years. Wouldn't use one for a touchy old tractor, though!
@tracychristopher3701
3 жыл бұрын
Why would you buy a $ 63 rebuild kit? You can buy the whole carburetor for$ 36 from Amazon, seriously........
@PlanetMojo
3 жыл бұрын
The carbs on Amazon are Chinese look-alike junk, seriously...
@billbraniger2306
3 жыл бұрын
This complete carbutetor from Steiner is between $300 and $400. So the $63 kit is the economical way to go.
@PlanetMojo
3 жыл бұрын
@@billbraniger2306 Correct 😊
@mikeburke8656
2 жыл бұрын
@@PlanetMojo I got my kit from Dan and Rachel Gingell. Don't remember all the parts, but was happy with the it. I use Steiner Parts a lot.
@bradhopwood5374
Жыл бұрын
Chinese replacement are NOT equal. Send in core and have one of the better carb shops rebuild it for 1/2 price of good new- that has always been the best option for me.
Пікірлер: 43