I've been sanding mine every other year as well. Recently I've discovered it's much easier to use a power washer to get rid of old coat. Give that a try.
@_jennifer.rose_
4 ай бұрын
So you skip sanding completely and just power wash then oil? Do you think it's necessary to use a brightener?
@theoffgridgypsy
2 ай бұрын
Everything I have read says to not use a power washer. Why is it all so confusing!
@ks-hg5vo
2 ай бұрын
Power washing will lift the grain which will be damaging
@mc2e100
Жыл бұрын
I apply 5 or 6 coats, especially for outdoor applications. It takes time,, but lasts and looks great. The instructions direct you to reapply it annually. It's biodegradable.
@sirjohnpiraan1662
2 күн бұрын
No time, life is short.
@chrisc.4630
3 жыл бұрын
What went wrong? Went from 60 straight to 220 grit, didn't apply or remove the product correctly, and that wood still looked ultra dusty when the finish was applied.
@snowsquatch7000
Жыл бұрын
160 max for penetrating oil?
@415hispfemale
Жыл бұрын
Was a great general video for people who already know a little. But, it should have mentioned you shouldn’t go from a 60-80 grit straight to a 220 finishing grit. There should at least be 2 other stages of grit. Also, depending on the finish already on there, you may need to first chemically strip it. A true pain, I know, but necessary if you’re looking to do it right. After that, sandings with an 80g, 120, 180, then a 220. Be sure to thoroughly wipe down with shop vac if there are lots of groves, followed by a tack cloth. You have to eliminate ANY dust before applying anything. Remember with any wood finishing, the prep is the crucial part to having a good outcome. Letting coats dry overnight is preferable if you’ve got the time. And stay in the same family. If you start with water-based, stay with water based, same with oil-based. Technically you can sometimes apply oil based over water, but never vice versa. You’ll risk fish eye, and eventual flaking. Apply 2-4 coats of spar urethane, using super fine 0000 steel wool in between coats to knock back tiny bumps and get that super smooth surface!
@415hispfemale
Жыл бұрын
One last thing - brush quality totally matters. For oil based, use a high quality Chinese bristle brush. Never use a multipurpose brush if the piece matters.
@daxshell242
3 жыл бұрын
if you are just oiling it, its pretty much an annual affair. you didnt do anything wrong, this is just the life of having an outdoor wood table.
@teamraacthemin6078
2 жыл бұрын
Personally I only used either Star Brite or my very favorite Semco. Highly recommend. I won’t even look twice at those at lowes or Walmart.
@ipaascity5603
Жыл бұрын
Starbrite is the 'walmart' solution. From my research, people that know all go to Semco and Cetton (sp?). Would love to hear more about the semco. Just dropped almost $600 for three gallons. Stuff is more dear than high-end scotch!
@jeffreylittlewood6237
Жыл бұрын
Refresh every year at least with a thin coat to seal the microscopic breakdown before you can see it. I met a sailor lovingly wiping his 50 year old boat for the 100th time and it looked like new..
@tarantulasuit
2 жыл бұрын
You can't go straight from 60 to 220. You get all those little swirly marks.
@whynot8586
2 жыл бұрын
I just purchased the Watco Teak Oil & Stain, but would love to hear if it held up for you a year later. Thanks!
@biketopia
Жыл бұрын
After the first coat assuming it’s a heavy coat, back sand it, get that top flat again, then apply another coat.. then sand that with an even finer grit. When I do outdoor teak furniture. I coat and backsand until you’re essentially applying the finish over an existing finish and the top has stopped drinking the finish. Why? Because then the top is sealed. When you do the annual or no annual cleaning, you’re not starting over. You’re just gently removing a layer of finish then, reapply another coat or two.
@daviddier5755
2 жыл бұрын
what is the one year old report on the Watch product? Thanks for providing the good content!
@Aznprada
3 жыл бұрын
How many coats? I generally put 3-4 coats on and then finish sanding with 600-1000 to get a smooth finish. Sure if takes off some of the Teak, but if you got enough coats it's a nice duller finish.
@eltomas3634
2 жыл бұрын
After that last coat is fully cured, you can put on a layer of automotive carnuba wax, preferably one with some UV protection in it, that helps a lot to shed water, dirt, and protect the oil finish. I use the spray on wax, makes the job quick and easy.
@robroy5729
Жыл бұрын
I recently purchased teak as decking material for my exterior porch. after a lot of reading the general consensus is that overtime these teak oils break down the teak itself as they are not oils extracted from the teak wood itself and way more often than not require an application YEARLY. On the other hand, teak sealer also is not a natural extract or oil from teak wood itself though the general consensus is that sealing is your best option as you are preserving and protecting the natural oils that teak has, thus requiring less maintenance than if you were to oil it.
@karlx-1
2 жыл бұрын
I've read that oil isn't suitable for outdoor wood. I think because it doesn't protect against UV. I was told (yesterday) that a sealer is best for any teak outdoors. I'm eager to see how yours holds up with oil.
@eltomas3634
2 жыл бұрын
Right on. UV rays are just brutal on any finish, but especially clear coats and with substrate that expands and contracts with moisture changes, like wood does.
@MrGizmo211
2 жыл бұрын
Mine held up pretty well - but it doesn’t see sunlight. It is under a covered deck.
@simplifysoap1113
Жыл бұрын
Teakwood oil is used on marine items like boats. It does need to be reapplied every few years.
@nataliedigiovanni4863
Жыл бұрын
Correct need spar polyurethane
@calisson47
Жыл бұрын
The company that sold me my teak table (which looks identical to the one in this video) says do *not* use teak oil! They recommend water-based finishes. And yes, if you do not want a gray teak table, it is annual maintenance.
@frankvitani8545
24 күн бұрын
Did you wipe down with denatured alcohol after sanding
@thegrimmperspective
3 жыл бұрын
When I've researched this product for a door I'll be doing in the future, the oil is supposed to be put on very liberally. If it soaks in you're supposed to add more. I believe you're supposed to allow to soak 10 minutes or so and remove with a rag. Then I've heard references to 3-4 coats??
@ThePlace420
2 жыл бұрын
30m
@EdwardMyers-qp9he
3 ай бұрын
I'm having a problem with the stain changing color as I go through can. I've tried to shake it more, but it still starts to get more gray as I get closer to the bottom of the can. Any suggestions?
@tf6534
3 жыл бұрын
Great video! Tim Winnipeg Manitoba Canada 🇨🇦
@peteryoung9164
Жыл бұрын
thanks for your video. it should help me on my way. I have a teak shower bench (indoor) that needs refinishing. is the oil finish enough or should I use an additional sealant? thanks again Peter
@nateb4543
Жыл бұрын
I assume if i don't sand ALL the grey off (deep grooves on the top) it won't take the oil/stain consistently? Hope im wrong, otherwise i might need to plane this thing
@ipaascity5603
Жыл бұрын
Everyone who says not to use teak 'oils' seems to agree that the linseed oil and other oils hurt the teak - make it rot. Any comment on that?
@MrGizmo211
Жыл бұрын
Mine didn’t last as great as I would have liked it - so I think there is validity to that statement.
@JohnLedoux1
Жыл бұрын
@@MrGizmo211 curious to know what it did that has turned you off the teak oil.
@robroy5729
Жыл бұрын
@@MrGizmo211 I recently purchased teak as decking material for my exterior porch. after a lot of reading the general consensus is that overtime these teak oils break down the teak itself as they are not oils extracted from the teak wood itself and way more often than not require an application YEARLY. On the other hand, teak sealer also is not a natural extract or oil from teak wood itself though the general consensus is that sealing is your best option as you are preserving and protecting the natural oils that teak has, thus requiring less maintenance than if you were to oil it.
@DM-qe1dr
Жыл бұрын
Any suggestions for sanding off a polyurethane coating on teak dining table? (It’s some sort of finish that is flaking off, not a wood penetrating finish). Start and finish with what grit paper? Appreciate any suggestions!
@MrGizmo211
Жыл бұрын
I would start with 80 grit to knock off the flaking. Then use 120 grit to get a smooth finish. I might even use a 220 grit as a finish. Generally 120 grit would be enough.
@johnnyonly163
Жыл бұрын
If it's on the surface like that, best to use a mild stripper first or that stuff can gunk up your paper/sander. General stripper is not used for teak since the oil soaks in, but it sounds like you have some sort of urethane on there, so stripper is the way to start. Clean with spirits. Let dry, then sand and finish.
@DM-qe1dr
Жыл бұрын
Thank you! Haven’t started this project yet- decided to wait for fall, so I appreciate your suggestion very much!
@raulmunilla6169
Жыл бұрын
Doesn’t an orbital sander leave a track on the wood grain?
@raywilson3166
2 ай бұрын
Not if you know how to use it
@07szim
Жыл бұрын
no pro here, but i read you shouldn't use teak oil on teak wood.... what i read said it causes mold to grow?
@07szim
Жыл бұрын
you didnt even clean off the wood dust from sanding my guy!
@barkingshark6413
2 жыл бұрын
60 G to 220 Grit.. interesting…. Or 60, 80, 120, etc?
@MrGizmo211
2 жыл бұрын
To be honest - I should have stepped it up more for a smoother finish and to sand less with the 220 :)
@FixItCleanIt
Жыл бұрын
Was there an update video?
@Robsay01
Жыл бұрын
Are you supposed to do the underneath too?
@MrGizmo211
Жыл бұрын
I always do one coat under
@ThePlace420
2 жыл бұрын
How did you get the dang cap off the can?
@MrGizmo211
2 жыл бұрын
Vise grips ;)
@ellensheppard9590
Жыл бұрын
YES!!! I had to take it back to the store to have them open it for me. That's ridiculous.
@jamaicanapple
6 ай бұрын
Same here... we put the can in a vice and applied downward pressure and torque with plyers. That eventually got the cap off, but it took some coaxing 👍🏼
@storyvillerox
3 ай бұрын
THIS is what I need help with!🤦🏻♀️🤪
@rommycougar
3 жыл бұрын
Awesomely, is teak oil enough or you seal additional lacquer ?! Thank you 🙏
@MrGizmo211
3 жыл бұрын
Teak oil should be enough to keep the table in great shape.
@johnbusher6375
2 жыл бұрын
No lacquer on teak.
@rommycougar
2 жыл бұрын
@@johnbusher6375 thanks a lot John , appreciated 🙏
@brenndanmcguire263
3 жыл бұрын
Did you sand the table with the same technique the first time around when the Minwax Oil finish failed?
@MrGizmo211
3 жыл бұрын
Yes - but I sanded a lot more this time around to be sure I had just raw wood.
@sbrycroft
2 жыл бұрын
Then maybe it was the lack of sanding that was the problem the first time, not the oil product.
@scotttownley5076
2 жыл бұрын
Use watch teak oil Finish. Lasts a long time.
@sammydavis991
2 жыл бұрын
Semco
@sudilos1172
3 жыл бұрын
Petroleum in that oil like in mine? Not good to suck that into your skin bro
@davistolpulitz
Жыл бұрын
This is NOT how to refinish teak. Use teak cleaner on a wet surface with a nylon scrub brush. Rinse well. Apply teal brightener when dry. Then when dry apply oil with foam pad
@starrstewart7083
3 жыл бұрын
Woodprix is a solid company with solid woodworking plans.
@nataliedigiovanni4863
Жыл бұрын
Need to sand between coats
@MKRM27
Жыл бұрын
From 60 to 220 grit? Oh dear. Far too big a jump. Need at least two intermediate grits, possibly four.
@Tom-oz7iy
Жыл бұрын
I am pretty sure you can start at 100 as that is what I have used on my table and it works quite well. I will finish with 220.
@thaddeusstevens1344
Жыл бұрын
HYPVENTILATING watching someone jump from 60 grit to 220 grit
Пікірлер: 73