Buy It Here! bit.ly/ChevySub...
This seems like a daunting task but can be very easy with the right guidance. Let us show you how to quickly replace your Suburban rear bumper cover. Our rear bumper fits the 2015-2016 Suburban 1500 Series and 2016 Suburban 3500 Series.
Hello folks! We're back at it again. We have a 2015-2016 Chevrolet Suburban rear bumper cover removal tutorial. This will be part of a 3 video series like all our videos. The shorter the video, the better. We like to get straight to the point. We are here to take the stress out of these DIY projects. Yes, with basic tools and some grit anyone can do this job on their Chevy Suburban.
0:00 Start
0:08 Intro to bumper removal
0:22 Tools needed
0:40 Passenger rear fender liner bolts
2:00 Driver-side rear fender liner bolts
3:33 Bottom of the bumper bolt removal
4:40 Bolt removal under liftgate
6:17 Bumper removal process
7:35 Unplugging the sensor connector
8:40 ReveMoto Outro
TOOLS NEEDED:
Socket wrench with a 10mm and 7mm socket and a hex key/Allen wrench.
REMOVAL PROCESS:
Here at ReveMoto, we love to start off on the fender liners. I'm not sure why but that is our go-to. You can skip around if you'd like and go straight for the bottom of the rear bumper, but leave the top bolts for last. You wouldn't want the bumper falling on you.
There are approximately six, 7mm bolts on the side of the rear bumper and the 6th one at the very top going into the quarter panel. Repeat the steps on the opposite side and move on to the next section of the bumper. We went for the bottom of the Chevrolet Suburban bumper after our two sides. The vehicle is pretty high, so there is no need to use a lift or jack the car up. There are four 10mm bolts on each end and two 7mm bolts in the middle. Very easy to remove these bolts, just be sure not to misplace any of the bolts. The last section we went to was the top of the bumper underneath the liftgate. There are two hex screws on each end. They are also called Allen screws because we know all Allens are hexagonal.
After these four bolts are removed you can pull the rear bumper off. Be sure to be careful not to let the bumper drop completely. Gently pull each end off the rear bumper brackets/retainer on the sides. We had a bit of trouble on the driver's side because the previous mechanic used 3m tape to hold the bumper, sheesh! Lastly, you want to unplug the rear bumper cover sensors. The good thing about Chevy, as they made one giant plug for the harness. Like most old things, it gets stuck over time. It may be a bit hard to do with just your hand. We used a small flat-head screwdriver to pry the latch-up. You'll see the latch is the white part of the plug. Gently pry it up or away from you, as you hear it click, the sensor will become looser.
Congratulations, you just removed your 2015-2016 Chevy Suburban rear bumper cover!!! We knew you could do it all this time. You just had to believe...and watch a step-by-step tutorial. But, you did it!
Source: www.revemoto.com
Follow Us on
FB: / revemoto
IG: / revemoto
Twitter: twitter.com/re...
________________________________________________________
#suburban #ChevySubruban #revemoto #paintedautoparts #ChevroletSuburban #highquality #DIY #HowTo #Chevy
DISCLAIMER: While ReveMoto tries to make the information in this video as accurate as possible, we make no claims, promises, or guarantees about the accuracy, completeness, or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself (DIY) projects entail some risk. It is the sole responsibility of the viewer to assume this risk. ReveMoto is not responsible or liable for any loss, damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Негізгі бет How To Remove a 2015-2016 Chevrolet Suburban Rear Bumper | Simple & Easy - Video 1/3 | ReveMoto
No video
Пікірлер: 18