Such a clear video, brilliant lighting, brilliant job thank you, liked and subscribed 👍👍👍
@rpsspain1966
Ай бұрын
Thank you for the great feedback, I hope the video was useful for you.
@cabdicazizmaxamedshekh7562
19 күн бұрын
Hallo Sir Really Ur Video Clip was clear and high quality thank you so much 👍
@rpsspain1966
19 күн бұрын
I truly appreciate your feedback! It's great to know that the quality resonated with you. Thank you for taking the time to comment!
@luciasmoore2705
3 ай бұрын
Tidy Job mate, thank you
@rpsspain1966
3 ай бұрын
Thank you for your support!
@dengodeherdenskyrkaovresop4183
Ай бұрын
brilliant video! thanks alot.
@rpsspain1966
Ай бұрын
I'm glad you enjoyed the video! Your support means a lot to me.
@simonpooley3829
Жыл бұрын
Fantastic video, thank you for your efforts
@rpsspain1966
Жыл бұрын
Thank you Simon, not published anything for a week or so as have been away, more to come this week.
@paulyoung-gb2sy
Жыл бұрын
Just changed a front bearing hub on one yesterday...surprisingly easy
@rpsspain1966
Жыл бұрын
it was for this one kzitem.infolZEb9T1ygO Engine out at the minute, hopefully get away with bottom end shells, however there was a lot of shiny bits in the oil.
@simonbone
Жыл бұрын
I did the left one last year, which was straightforward apart from some very sticky bolts. This year I did the other side and everything was seized together - the knuckle, backing plate, and bearing. Fortunately, replacement parts not too expensive. Also a good time to replace control arms, drop shafts, and possibly tie rod ends. Fairly simple compared to the rear suspension, at least if you're doing it on the driveway.
@jimbowen501
Жыл бұрын
I have a 2013 petrol qashqai and When a mechanic says the drive shaft is totally fudged does he mean the whole front drive shaft or is it something totally different and is the prop shaft...I had cruching coming from front suspension the last month and got really bad this morning and all i could here was banging and the car was going really slow.
@rpsspain1966
Жыл бұрын
I can not answer for your mechanic, totally fudged is not a diagnosis, he needs to be more specific.
@daveski87
Жыл бұрын
Hi there, how much transmission oil does the gearbox take? Thanks
@rpsspain1966
Жыл бұрын
Manual transmission litres2,0 Transmission type RS6F52A
@ashleyseeley8409
8 ай бұрын
Do you have to drain the gearbox oil when you changing it?
@rpsspain1966
8 ай бұрын
You will lose oil if you pull the shafts.
@bkfilms5843
3 ай бұрын
@@rpsspain1966Yh but how much oil ….
@rpsspain1966
3 ай бұрын
@@bkfilms5843 If you drain the oil apprx 2ltrs. you need to check the spec for your vehicle gearbox......Manual transmission, RS6F52A, 6-speed Gear oil (Preferred lubricant specification) Homologation OEM Temperature Viscosity Nissan MT-XZ Manual transmission RS6F52A Gearbox refill 2.0
@rasmadrak
10 ай бұрын
Would you say this way is easier than removing the bottom ball joint? This seems easier, although removes more components. I'm "looking forward" to doing both drive shafts on my drive way in a near future, so I'm looking for the quickest and easiest way... 😅
@rpsspain1966
10 ай бұрын
Thank you for watching and taking time to comment. Yes, for me as you do not need to separate the ball joint.
@MadZprod23
Жыл бұрын
Hiya mate, my qashqai's drive shaft bearing carrier snapped, do you know if you can buy the complete bearing and carrier seprate from the drive shaft or is this going to be a new drive shaft job. Tah
@rpsspain1966
Жыл бұрын
Bearing carrier is a separate part, not sure about the bearing though.
@EvertHarley1
Жыл бұрын
what whas the reason for the removal? i have a (Dutch) J11 too with a ramblin driveshaft on the right side when accelerating and when i drive up (about 1%) my lane it makes a "clongkin" sound could it be that bearing ?
Пікірлер: 27