I always use a torque wrench when removing old glow plugs, to ensure I don’t snap them. I also start with a hot engine and use copious quantities of penetrating oil. Usually some of the plugs come out relatively easily at something like 30NM but there are always some that need 35NM or 40NM and often multiple attempts over a 30 - 60 minute period with additional applications of penetrating oil. Of course the engine is also cooling down during this time so it’s a delicate balance of force and patience. The bit I hate most is the horrible screeching noise some plugs make as they are unscrewed. It’s like nails on a chalkboard!
@ReCheck_WotTheFluck
5 ай бұрын
Think you got lucky drill didn't wander anymore. Don't know why the kit didn't use left hand drill bits. But got it done. Stress level - high.
@ahmedrazak2063
3 ай бұрын
I think one reason that makes it more likely that an old glow plug may snap is undue side load. I'll try to explain this; So as well as the rotational torque, if you are not careful you can apply a side bending force that will cause the head of the glow plug to bend side ways a little when you apply force. This is made worst if you use longer extension bar on your wrench as this acts as a lever applying more bending force if you are not careful. I suspect it is this force that cause the glow plug head to snap. If the force can be kept purely rotational then I think the old plug will come out without snapping. What do people think agree/disagree? (May be someone out there can do a controlled test to prove this or not).
@voithRetarded
Ай бұрын
Well explained physics
@chrisshave7129
Ай бұрын
Thanks for great content! When you re-tapped the glowplug threads how do you prevent bits of swarf getting into the engine?
@martinhiggins6016
5 ай бұрын
I’ve been looking forward to this one. Because of this risk I had put off doing glow plugs when I had a diesel.
@steveng5503
5 ай бұрын
Well done mate! It’s easy in such situations to become distracted and start grabbing at the incorrect tools for the job and stabbing at things, making things worse if not careful. There’s a lot to be learnt from this video. 👍🏻
@GeorgeAusters
5 ай бұрын
Thanks mate
@rednax1396
5 ай бұрын
Just did my glow plugs on my e90 318D and while getting to them was a bear, they came out eventually so for that i am grateful, i bought a removal kit before i started.... just in case but thankfully didnt need it. Without your videos i'm not sure i would have even attempted this job but thanks to you i was able to complete it and now she's on the road again. TY George.
@GeorgeAusters
5 ай бұрын
You’re welcome!
@nikokristiansbodnieks2147
21 күн бұрын
With this set come easy and fast out. Got electrode out with welding and bending and then spinning, then drilled out, tapped with thread M10x1.25, in set was only M10x1 and M8x1, vacuumed, tapped thread for glowplug, vacuumed, screwed end for extraction tools, and started with wrench till it got out, ez. Good set, but drill small end broke off, but another have small end
@tlabort
5 ай бұрын
George you have done a Really good job i messed up by drilling slightly into the head and did not remove the glow plug I ended up having to get a second hand head and replace it which was ok the only thing that was hard was the head bolts are to get off and to replace HATS OFF WELL DONE
@GeorgeAusters
5 ай бұрын
If you do drill into the head then you can just get an oversize thread insert
@robc5955
5 ай бұрын
My idea of nightmare, well done.
@NinpoUK
5 ай бұрын
Sounds loads better George! Great job getting that one bastard of a plug out. I used your I think E46 video with the M47 for the ones on our older E91. Still got it mate!
@MarkLeamy-e6o
5 ай бұрын
Well done George nice job
@KianWard-b9q
5 ай бұрын
that job was just amazing to perfect fairplay bro very tricky job to do but you did an amazing bit of content for this channel id say that would of cost a right few bob in a garage for this repair stunning work bro happy days it worked out for you pal delighted for ye👌👌👌👌👌👌👌👌👌
@peterarries7879
2 ай бұрын
Nice job
@rogerkretzschmar8280
5 ай бұрын
Well done! Were you not a bit worried about the glow plug tip dropping into the head when you drilled it's thread out?
@michaelclutton8446
5 ай бұрын
I wondered about that
@GeorgeAusters
5 ай бұрын
It couldn’t drop down as the tip is connected to the shaft and the shaft is too big to fall down
@mcplutt
5 ай бұрын
You mean into the cylinder? Probably wise to have that piston at TDC. But I guess the hole for the glowplug tip isn't large enough for the rest of the plug.
@bobfrankish8883
5 ай бұрын
You're a brave lad George, I'll say that! That tool set gets more really bad reviews than good, so I think you did well. Possibly with a bit of machining by your dad, the tool could be made to sit correctly on the BMW head, which could make all the difference. Anyhow, well done again.
@GeorgeAusters
5 ай бұрын
It’s a very simple kit really so don’t know how people can say it doesn’t work
@bapsmcginty4782
5 ай бұрын
@@GeorgeAusters It looked like it was screwing into the plug rather than screw it out. Like an easiout would. Optical illusion?
@abdulb1162
5 ай бұрын
When your doing glow plugs on these N47 engines, should you always replace the glow plug module as well or can you just leave it?
@thestorytelleruk
4 ай бұрын
Getting to these plugs is a dream compared to my Citroen C3's, which are located right at the back of the engine! Have to remove the scuttle panel, air filter, etc. And still you need to work backwards with a mirror! Absolute nightmare.
@NinpoUK
5 ай бұрын
Also George do you have a slide hammer you could adapt to that removal kit? Screw an end of a slide hammer into the tapped piece and use the hammer to knock it out
@GeorgeAusters
5 ай бұрын
Yes I do, that would only work once you have drilled through the threads completely
@matthewhaddon599
5 ай бұрын
I had glow plugs changed at a small garage, but sadly they used the wrong plugs. There are 5v versions and 11v versions. They used 5v by mistake so a week or two later they failed. As I was on holiday when they were fitted, I had to change them again a few weeks later at home. They did come out easily! I didn't complain to the garage as they were probably given the wrong plugs by their supplier and didn't realise. That was on a Freelander 2.
@GeorgeAusters
5 ай бұрын
I only use the genuine Bosch plugs that BMW uses
@banzaiman1
5 ай бұрын
I think some of the kits come with a drill guide. My drilling definitely wouldn't be straight
@GeorgeAusters
5 ай бұрын
This kit does come with guides and smaller bits to get you started
@jackdanielsamarreto
5 ай бұрын
How do you stop the iron fillings going inside the engine ?
@metalworker007
5 ай бұрын
The taps usually have slots running down them, you fill the slots with tapping grease ..and the swarf should end up in the grease and not on top of the piston
@GeorgeAusters
5 ай бұрын
While the glow plug is in place, the swarf can’t fall down into the cylinder so just vacuum it out. But yes you use grease to catch the majority of the swarf👍🏻
@peterpaliwoda1527
5 ай бұрын
Nice work George…Will it be ready for the road trip to Wembley?
@GeorgeAusters
5 ай бұрын
Of course!
@peterpaliwoda1527
5 ай бұрын
@@GeorgeAusters thought that might motivate you !
@B3MMi
5 ай бұрын
0:50 No, I don't think that's true. I changed glow plugs on N57, completely cold. Sitting for 2 weeks and during winter. Every single one of them came out very easily. Even after 300k mileage. Used torque wrench on reverse setting. Remember to change them in time, use a torque wrench and put a bit of ceramic grease to make the job easier gor the next person. 😊
@Bercilakdehautdesert-yt1gd
4 ай бұрын
I had a snapped tip stuck in the bore of a Saab 9-3 Tid. I soaked it in 50/50 Acetone and ATF mixture and strapped a chunk of wood above the bore, then drove. After 200 miles there was an almighty bang and the snapped tip was ejected, hitting the block of wood, saving a bonnet ding. I was sort of concerned that the tip might go the other way and through the engine but really, the detonation forces are way more powerful than those generated by the the intake stroke. It is worth noting that the tip was unscrewed from the bore by 12mm or so, no part of the plug tip was actually inside the combustion chamber. Had that been the case I would have removed an injector and pushed the tip out.
@anthonyballard6906
5 ай бұрын
I had an exhaust leak from my downpipe with fumes coming into the cabin. It turns out someone had removed it before and didn't put the gasket in. 🤦♂️
@sammason411
5 ай бұрын
They don't all have a gasket listed
@anthonyballard6906
5 ай бұрын
I put one on and it's stopped the exhaust fumes coming into cabin so must have needed it
@bapsmcginty4782
5 ай бұрын
Lets hope Ipswich dont go as well as your improvised heater plug removal🤣 MOT
@tonyjones7372
4 ай бұрын
There was a F-type on e-bay that had been written off because of snapped glow-plug. I was too scared to buy,
@GeorgeAusters
4 ай бұрын
Diesel F type?
@tonyjones7372
4 ай бұрын
@@GeorgeAusters yes, your right, sorry, will have been injector. doh! apparently common problem.
@mumbtie
5 ай бұрын
Let's hope so 😂
@maxcrompton4073
5 ай бұрын
is that a f series 20d in a e91?
@GeorgeAusters
5 ай бұрын
They used this engine in E and F chassis
@piyush1419
5 ай бұрын
Please help bmw e90 mileage is fluctuate heavily
@waynehaines4889
5 ай бұрын
8.u hi
@waynehaines4889
5 ай бұрын
Û
@-sargntclashroyaleandmore-491
5 ай бұрын
Whats next on project KFC eh 😅
@GeorgeAusters
5 ай бұрын
Hopefully not a lot lol
@bigpouse
5 ай бұрын
Hi George. I was after some advice if possible. I was removing my glow plugs tonight. (Same engine - 320d). I followed all your previous tips. Releasing fluid a few days ago. Hot engine. More releasing fluid etc. I cracked the first plug off slowly. It felt good. Wound it in and out as I went. More releasing fluid. About 2 turns out and I realised that now it is just spinning. I've clearly stripped the threads out of the head. Any idea if I can get this out from the outside or is this a head off job? Thanks.
@GeorgeAusters
5 ай бұрын
Is the plug snapped? Try pulling it out
@bigpouse
5 ай бұрын
@GeorgeAusters No it isn't snapped. I've tried pulling it out. No joy! I'll try again tomorrow when I've had a good night's sleep!
@Coops95
5 ай бұрын
Another vid of yours into the archive, quality having a tutorial for pretty much everything and anything on the car/engine you own without all the shitty loud music or pointless info that most usually have 😂 up the colonal 🫡
Пікірлер: 60