The only mechanic with a detailed video in KZitem. Seriously!! Good job!
@PiliaeAl
3 жыл бұрын
Seriously the best transmission replacement video with clear explanations .
@ShopLifeTV
3 жыл бұрын
Thank you!
@herlegz6969
2 жыл бұрын
It's like bmw puts all of it's engineering effort into making maintenance as cumbersome and frustrating as possible.
@GeeIce
2 жыл бұрын
Because of this video I was able to do my own transmission. 330i 2006 Saved me money and time. Thank you so much. I have no experience btw 🤙🤙🤙
@reallife386
Жыл бұрын
the driveshaft does not have to come out
@ShopLifeTV
5 жыл бұрын
New Merch On www.shoplifetv.com ZF 6HP Troubleshooting: kzitem.info/news/bejne/wo5myJyromqGi3Y ZF 6HP Fluid/Filter/Sleeves: kzitem.info/news/bejne/k51jm6mPmIJoqHY
@juliankwa9491
Жыл бұрын
Those step by steps are amazing. Great job.
@VTEXVSI
4 жыл бұрын
Great videos. I was on the fence about selling my 335i E93 since I am starting to have oil leaks and some other problems but decided to keep it as a project car. Started looking for some KZitem vids and found your channel and I'm really impressed with your vids. You sound like a seasoned BMW tech but look way too young :). Anyways, keep up the great work!
@mesidon4
Жыл бұрын
Fantastic job, your automotive nomenclature is top notch 💯
@MrLs1986
5 ай бұрын
Step by step.. well presentation . Thank you so much, now I'm ready to do my 328i transmission replacement. Good job.
@kevinhooper6007
2 жыл бұрын
Amazing video. Very well done with very clear explanations
@Hff19927
7 ай бұрын
Brilliant video. Can you do an e90 clutch change video?
@razorrich
5 жыл бұрын
Good Vid Guys - always a detailed step by step. Should have convinced the owner to swap in a 6MT, lol!
@ShopLifeTV
5 жыл бұрын
Thanks! And he daily drives the car, usually during traffic so he wanted to stick with an Auto
@razorrich
5 жыл бұрын
ShopLifeTV 👍🏻 I see. I know exactly how it feels like to be driving a manual in one hour traffic - left leg cramps and exhausted after driving, lol!
@sorinverdesi1284
4 жыл бұрын
Shoplifetv where you based
@williamghau1150
5 жыл бұрын
Do you need to program the new transmission to the car for it to work? Or you just need to put it on and it’ll work like normal again?
@harisbarra9805
3 жыл бұрын
Need a answer to this
@okantarakci3674
3 жыл бұрын
@@harisbarra9805 no need programing
@N54.S6
3 жыл бұрын
@@denisovanhybrid9610 Unless it's going from manual to automatic or vice versa, then reprogramming should not be needed.
@N54.S6
3 жыл бұрын
@@denisovanhybrid9610 I swapped my transmission roughly a year ago along side a buddy who owns a shop just 10 minutes away. I didn't have to reprogram any thing and the trans work's fine. It's a 07 335I e90
@N54.S6
3 жыл бұрын
@@denisovanhybrid9610 He doesn't know how to work on BMWs, I just use the shop and have him help out with things I can't given my back surgery. He doesn't touch anything Euro. I'm telling you, I did a swap with the same trans and it worked fine. We even had AutoHex on standby but, was not even needed. I'm just as confused as you are. New mechatronics unit and transmission "new old/used". Had codes like crazy, reset everything related to the ECU and transmission via Inpa, and boom, was fine. Not stuck in neutral, started right up. Not sure what I would get out of lying lol. I even have a video on my channel of what my trans was doing before the swap. Maybe, you don't know exactly what you are on about but, i am more than aware that you need to reprogram the TCU after. Hence why Hex was on standby after.
@DjDestinyChicago
5 жыл бұрын
I can't believe I used to do this on the ground with a shady ass jack lol Good Video!
@ShopLifeTV
5 жыл бұрын
I used to do jobs like this and even more in the dirt, with Jack's and plywood so that it wouldn't sink in, when I used to be back in NC
@editorialkiddos939
Жыл бұрын
What pressure or torque should the bolts be tightened to when reinstalling the transmission, this is a great video on removing it. Do you have a video where you show how to install it again?
@LuisGonzalez-ph8zp
3 жыл бұрын
Great video man my trans finally gave out on me gonna be replacing it soon just waiting to get paid order a preowned trans with low mileage take it to a homies shop and knock it out real quick judging from how strait forward it is I think we will knock it out with in 4 hours or less
@jxx90s
2 ай бұрын
Good job. Very clear explanation. Thx!
@jf269
5 ай бұрын
Just a time saver, you don't need to crank at the front to move the torque convertor. It moved pretty easily with a prybar in that little cap at the bottom of the transmission.
@ArtinFlight2
Жыл бұрын
This video is super helpful. Thank you for doing such a great job
@alexanderalexander2797
11 ай бұрын
Greatly helpful video ! Very detailed explanation! Cheers!
@iBryaaannnn
3 жыл бұрын
So if you can, do you mind answering where they asked if you need to program the mee transmission? Seems to be your most liked comment
@n54sparrow92
3 жыл бұрын
Do u need to program the new transmission if u do a swap on a 2009 135?
@liamrossiter1427
Жыл бұрын
Do you have to re program the transmission control module? I’ve heard that if you don’t in some cases you finish the job and the car will be stuck in park
@custommetalcreationsbykevi6572
3 жыл бұрын
Amazing videos and very detailed man... my question to you is I have an 08 335i auto and apon trying to do a burnout launch it started spinning the tires and then a big "thud" happened from the transmission and I immediately stopped after that! When I started driving away after that 1st year was fine 2nd year ribbed to the moon Under full throttle And everything else was OK. Days later I tried the whole dayeah sprite the holding the throttle to the floor for one minute to reset the computer and it surprisingly worked it surprisingly worked for about 5 miles then else then all the sudden it started slipping in 2nd gear again and 3rd gear. My question is I have a new used 2008 transmission to replace it with But do I swap out the entire transmission or do I just change the mechatronic valve body? And if I replace the transmission completely does it have to be reprogrammed for a 2008 or not? Your help would be greatly appreciated I've gotten so many different answers
@The_North0
2 жыл бұрын
Your thud likely has to do with wore out stator bushing inside the transmission. The whole transmission has to be removed to replace it. Recommend replacing the clutch friction as well while are in there
@sgtmaj2
Жыл бұрын
Hey, I found your removal videos very helpful getting my transmission out, but I can't seem to find a single install video anywhere and am having an issue with my install. I can't get the flex plate and torque converter to line up all 4 bolts. I've tried every combo matching of holes but one never lines up. I've looked for one hole smaller than the rest, but it seems like I have 2 next to each other that are oblong side to side and the other 2 are oblong top to bottom. Everything spins as it should, the transmission went together with no problem, I'm kind of at a loss to explain this and can't seem to find any info on it anywhere. Do you know of any install videos or a forum post about it that you could recommend?
@AutohausGarage
5 жыл бұрын
Loved the video bro. I need to get out there to turn some wrenches with you.
@ShopLifeTV
5 жыл бұрын
Thanks man!
@dillonradcliffe7745
Жыл бұрын
Thanks for this video definitely gonna come in handy if I decide to do my 8HP swap my self
@stefanyotcev5479
5 жыл бұрын
2012 and this is atleast the secont trans change ? WOAH WTF :D
@ojsannals6877
2 жыл бұрын
Is there a video showing the installation process?
@theazndudelivefree
5 жыл бұрын
I think my e93 rear main seal is leaking. This is gonna have to be done if I wanna keep the car.
@MiguelLopez-rh9mt
25 күн бұрын
Hi God bless you. Still are you doing BMW 328i xdrive 2011 transmission?
@emreyesilyurt8505
Ай бұрын
Mechanic, my car (BMW E90 3.16i - 2011) goes into limp mode and gets stuck in 3rd gear, especially in hot weather. This issue does not occur in cooler weather. The problem arises after the car has been running for a while.
@johnvarney1844
Жыл бұрын
I have a question. If your removing the engine only how would i get to the top bolts on the bellhousing. Excellent video and very informative 👍
@xans777
5 жыл бұрын
Dang if only you uploaded this a few days earlier I could of used that drive shaft removal tutorial when doing the center bearing
@roccoelleto9900
3 жыл бұрын
Thanks for the video. Gunna have to pull mine on my 08 335i E93 for a rear main seal. Great Video!!
@adamrichardson6918
4 жыл бұрын
Great work man, getting ready to do my X5d this was perfect for bell housing bolt location, earned a sub!
@donovanh5679
3 жыл бұрын
Impressive job, well-done! I have watched a Wheeler Dealers episode where Ant Anstead converted an E46 M3's DSG to a manual gearbox. Here is my question: I have an e93 M3 with DCT and would like to convert it to a 6-speed manual. I wonder if there are professional shops that can do this job for me?
@tannerragsdale2862
4 ай бұрын
You’ve got to be insane.
@Mix3dbyMark
3 жыл бұрын
Holy crap... this is an insane amount of work
@romeojacob2339
3 жыл бұрын
You prolly dont care at all but does anybody know a tool to log back into an Instagram account? I stupidly lost the login password. I appreciate any tricks you can give me
@austinedgar7462
3 жыл бұрын
@Romeo Jacob instablaster :)
@romeojacob2339
3 жыл бұрын
@Austin Edgar i really appreciate your reply. I found the site through google and I'm in the hacking process now. Takes a while so I will get back to you later with my results.
@romeojacob2339
3 жыл бұрын
@Austin Edgar it worked and I now got access to my account again. I'm so happy:D Thank you so much, you saved my ass :D
@austinedgar7462
3 жыл бұрын
@Romeo Jacob no problem xD
@metinorak8780
Күн бұрын
I have a problom with my 2003 318d bmw gm 5l40e transmission. Firs start after 5 and more hour parking, car doesnot move in D gear, firt ı shift to M1 and M2 after2 minutes driving the car, ı shift back to D and the the problem disappears. What can cause this problem
@scottcrawford4148
Ай бұрын
The parts and job is similar for my 2013 F30.
@morifusa
3 жыл бұрын
Is it possible to zf6hp19 swap to GA6L45R?
@Rpd88
6 ай бұрын
Where is the video show install back the gear box?
@antslife1089
2 жыл бұрын
Do you a video of putting a transmission back in place?
@erniewhite9595
4 жыл бұрын
Your videos are awesome and not full of useless ramblings. Im a new subscriber and also a new owner of a 2003 BMW 330xi. Im having a hesitation when I shift from reverse to drive. It acts like its not in gear for a few revs then it catches, it also has a jumpy RPM at idle. . I have a rip in my upper throttle body intake boot, I'm aware of and have gotten a Pl code on my upstream, bank 2 ,02 sensor. Could these be my problems ? Any advice before I start wrenching and dropping $$$ and time. Thank you and keep up these awesome informative videos.
@JohnSmith-dp3cx
7 ай бұрын
Question, I have a BMW 2011 740i and I would like to know what other transmission is compatible with this car? I cannot find the exact transmission but I can locate other transmission 5 series, 3 series and 6 series. Thank you in advance.
@glenglene8473
3 жыл бұрын
Hi Shoplife, my 2011 335xi makes rumbling noise in park, neutral and more pronounce in drive. But the noise goes away in reverse. What could cause it? Can bent flex plate cause it? thanks man.
@AkeLovesGAMES
3 жыл бұрын
Thanks for the video, super helpful. Hope you do an N54 removal and replacement video as well!
@AsterixSlashStar
3 жыл бұрын
It's the same transmission as the N55 I believe
@AULIGAofBLEED
3 жыл бұрын
Great video and awesome detailed explanation. subbed.
@ShopLifeTV
3 жыл бұрын
Thanks Rob!
@Xatxitor
4 ай бұрын
I need help. My E90 335i wont get into gear. there's no trouble code. Should I replace it or is there anything I could try before?
@tiago_BMW
3 жыл бұрын
Anyone know how much torque for the bolts of converter to flywheel when reinstalling ?
@gulag8735
4 жыл бұрын
Is there a clutch against a flywheel in an automatic. Forgive my ignorance. Great video.
@mq2825
5 жыл бұрын
Whose the new helper? Btw awesome detailed video! Keep it up!
@ShopLifeTV
5 жыл бұрын
Thanks! And he's Selena's brother
@julianjohnson7627
2 жыл бұрын
I need information on my 07 530i been watching your videos they are extremely helpful I know my torque converter is bad it rattles trans is still good car only has 117k miles my only question is where do I source a torque converter none of the local part stores can order it
@garygrenier
3 жыл бұрын
Thanks Man! Just found this. Doing a rear main seal on a 2008 335xi and this is VERY helpful!! Great Job!!
@drollerbark5282
2 жыл бұрын
How long did it take you to do im getting ready to do the same to my car
@Silver_Cody_Suecroft
3 ай бұрын
Can anyone share a link for the 6L45 swap? Or is this going to be the exact same procedure ?
@jamescc2010
Жыл бұрын
For 2016 BMW X4, after replacing transmission and engine, do we need to reset or reflash ECU first before adding new keys to start car? I am not sure the guy used the same part numbers for trans and engine.
@jurgeenhandazola3006
Жыл бұрын
I have a Bentley with ZF6HP26A I set the transmission to N underneath and I can't move the drive shaft ¿why?
@briansanchez1193
4 жыл бұрын
Do you need to program the new transmission
@bigdeal87
3 жыл бұрын
I think you can just overtake the old control module and all should be fine..
@LulzSec777
Жыл бұрын
I wonder if its my trans thats making my car skip? could that be? it seems to run good no misfire codes just when you drive it will kinda stutter or jerk like a bad skip at times but dont feel it in the engine. wonder if fluid low or just bad trans?
@mohammadamin2139
Жыл бұрын
Hi can you tell me propshaft replacement tools please
@AshwinLB
4 жыл бұрын
Using this for reference for my manual swap!
@Praudas
2 жыл бұрын
It should be programmed after the change?
@khairulalif3946
5 ай бұрын
Very clear explainations🫰🏻🫰🏻thank youu bro !!
@W15Garage
5 жыл бұрын
Hi, saw you video, and I would like to get some help from you. My BMW X6 350d zf26 goes into limp mode when upshifting from 4th to 5th gear. The error code I’m getting is 4F85 gear monitoring coupling E. I have replaced the adapter seals+bridge seal, and put in new ATF fluid, reset the adaptations, but the problem is still there. No fault codes and issues while driving locally in the city, when I am using gears 1-4 only. Please help with your advice. Would replacing the stator bushing on clutch E solve the problem? Many thanks vilmos
@user-uy6qj7hc3v
4 жыл бұрын
I have the same issue did you find out what the fix was?
@W15Garage
3 жыл бұрын
Hi, the issue was with the bushing rings inside the transmission. Clutch E was worn badly, but as a precaution I’ve replaced all of them, as the bushings come in a kit. Before this I’ve tried changing the rubber sleeve adopter tube (above the mechatronic unit), which also came in a kit, but that didn’t fix the problem. If you need any more info or pictures send me your email address, and I’d be happy to help.
@georgewatson6246
2 жыл бұрын
Good video bro .my 2010 bmw 328ix the transmission broke. It worth it to replace with use one ?
@l8nit3tr0ubl3
2 жыл бұрын
Great video, is the process essentially the same for those with the GM transmission? (2011 328xi e90)
@davebarbieri1380
Жыл бұрын
Yes, please answer.
@MrNicoe36cabrio
5 жыл бұрын
Great DIY guys. But why did the replacement transmission already fail?
@ShopLifeTV
5 жыл бұрын
Thanks! And im pretty sure the clutches were already worn out since the trans was not "low mileage" like the shop that sold and installed it claimed.
@FlySindbad
4 жыл бұрын
Good video.. But where i can find the transmission control unit in the car.. X3 E83 2009??
@rudyzavala3437
2 жыл бұрын
Great video thanks
@angelmendoza7402
Жыл бұрын
Is the process the same for the xdrives?
@JuanTorres-pq8fd
8 ай бұрын
Is there 10 bolts in total or 11
@johnnykamacho808
2 жыл бұрын
Looking to swap my transmission out of my 328xi. Is this the same process for the AWD models?
@josesoto307
2 жыл бұрын
Does new trans need to be coded I have a 08 335i keep getting a 004f85 and 004f95 code and trans has been serviced still no changes
@armandobronca1781
3 жыл бұрын
Thats a big job
@antslife1089
2 жыл бұрын
Do you have a video of rebuilding a ZF 6HP19 transmission?
@emielb2002
7 ай бұрын
I need a video form a automatic transmission of a bmw 318 d 2008 does anyone has a link?
@huanweili7699
3 жыл бұрын
I have one question. How do you get to the torque converter bolt if the engine is seized and can not turn the crank anymore? Any information will be appreciated 👍.
@nealongreene15
Жыл бұрын
Remove the oil pan, remove crank rod caps, then turn engine by force.
@stanislavgochev8485
4 жыл бұрын
Good job 🙂 where is your service ?
@fadeenanaa4495
3 жыл бұрын
please answer my comment i have 135i n55 DCT trans is it the same procedures or completely different because im planing to DIY to replace the mechatonic pan gascket thank you
@bboy1198
5 жыл бұрын
great video! do more N55 videos!!
@ShopLifeTV
5 жыл бұрын
We are!
@Cryformeshaftlicker
Жыл бұрын
Where can I get replacement bolts for the bell housing not just the starter ones??
@PartiBuoy
Жыл бұрын
13mm is stock size but only side of 4 screws
@PartiBuoy
Жыл бұрын
use 3/8's drive torque wrench set the foot pounds i know it dosent matter but I used 30lbs only
@anowzanaw4189
3 жыл бұрын
Really clear that thank you good job
@bmva8263
3 жыл бұрын
How much would you charge for this job?
@freddytorres8470
3 жыл бұрын
Hi , I watch your video all the time. So I have a question for you if you can help. I have a 2005 bmw 745 li and have a multiple missfire. Can you please help me what can be wrong. I changed the spark plugs and coil, but still the same. Also have a noking sounds. Please help.
@hungkhong5480
4 жыл бұрын
Excellent, good instruction thank you
@aylajpg
Жыл бұрын
is there anywhere i can get a tool list?
@MKRN98
5 жыл бұрын
I want to be sure I don't have to replace my auto-trans in my 335xi. When the car is cold, transmission shifts hard, whole car just jiggle at the moment of gear change. When it warms up it shifts fine, just little harder shift from time to time. But then I shift to DS, when I floor it, it will stay in gear for a moment, then shift really hard to each lower gear. It is upper seal that's leaking and I lost fluid or is the transmission already shot? I don't want to spend money on oil pan and all seals if transmission is not worth it.
@helixworld
5 жыл бұрын
Previous shop only did the job 50% complete. I'd be surprised if they can fix anything at all.
@ShopLifeTV
5 жыл бұрын
I see too many jobs like that, even from reputable shops
@dallen7049
Жыл бұрын
Great work I like your video great jiob.
@basithph8958
5 жыл бұрын
Should have done a manual swap Jk good video bro!
@fzall1457
Жыл бұрын
How long is the first extension attached to the wrench @22:22? Thanks!
@fernandopontaza142
5 жыл бұрын
Hello congratulations for your videos which are very well explained, I want to ask you a question Is it the same procedure for an e90 328xi 2008 model?
@xans777
5 жыл бұрын
It should be mostly the same but you will have extra steps to disassemble the powertrain in the front
@felipemendez7214
2 жыл бұрын
Can I swap a zp to GM I have a 2005 325 I automatic zp and brought a 2002 GM
@michaelmosley5345
4 жыл бұрын
Can I just change my valve body on my 535i then taking out the whole transmission it say Shift soleind
@nickwandtke7679
5 жыл бұрын
Not topic of video but wondering, I have a vacuum leak and idk where it is, my disa valve went bad and I replaced it, but I still have a whistling sound, and it's coming from either the side of the disa valve or under the intake manifold, so I'm not sure if it's maybe the intake manifold gasket or a hose is leaking and I'm not sure which one, also car is 2001 Bmw 325i, if anyone can maybe help would be much appreciated
@Kingcustomz
5 жыл бұрын
Great video guys
@ShopLifeTV
5 жыл бұрын
Thanks man!
@Kingcustomz
5 жыл бұрын
@@ShopLifeTV your welcome buddy
@exaltedgordo
3 жыл бұрын
how much would it cost me if i were to manual swap mine, and sell the automatic trans (manual trans-auto trans=?) and how difficult would this be? (are the transmissions hard to find, what else will i need to install?)
Пікірлер: 208