Hey bro, what are the name and part number of the factory tool that you use? Thanks
@WildWonderfulOutdoors
3 жыл бұрын
Marine Tech Tools Mercury Flywheel Puller Part No: AMT0023 Good luck dude. Easy job.
@deplorablechump8758
3 жыл бұрын
@@WildWonderfulOutdoors I ordered it and a stator. Can’t wait to put my boat back in water. Thanks.
@WildWonderfulOutdoors
3 жыл бұрын
Awesome man! Glad to hear it! Thanks for checking out my channel! I'm on the road to 1,000 subscribers!
@deplorablechump8758
3 жыл бұрын
@@WildWonderfulOutdoors Keep sharing. It really helps us save money and spend more time fishing!
@WildWonderfulOutdoors
3 жыл бұрын
@@deplorablechump8758 That's so awesome to hear! That is my goal, help everyone with budget in mind.
@ryanjames5799
3 ай бұрын
Thank you for your showing how to install the flywheel, yours is the first video I have seen that actually show the important steps and not cut them out during editing. Thank You
@robbyrabit
3 жыл бұрын
O.L is open lead, means the two leads have no continuity.
@gutaroker90
Жыл бұрын
Those stator screws are 55 inch pounds lol and should be lock threaded! Otherwise awesome job! Also if you have the v-6 blocks there is no key, the flywheel is grooved Also never torque with your impact ... torque to specs. That's how you wreck your bearings for your connecting rods. Just sharing my mercury knowledge as a tech.
@haydenneeson1716
4 ай бұрын
What’s the torque spec for it mate if possible
@wg7644
2 жыл бұрын
Harbor Freight bolt type whell puller is all you need - did my 2002 40 hp mercury in 3 minutes.
@goodguessgarage4265
2 жыл бұрын
Nice. This took about three seconds.
@WildWonderfulOutdoors
2 жыл бұрын
Yea this tool was designed specifically for this. It just popped right off with the impact.
@wg7644
2 жыл бұрын
@@goodguessgarage4265 and sixty dollars lol but I digress I am not a tech - NO NEED TO BUY AN EXPENSIVE TOOL PEOPLE
@WildWonderfulOutdoors
2 жыл бұрын
I'm a tech in the automotive industry. Expensive tools pay off all the time. To each their own, though.
@hookedonthebay3890
2 жыл бұрын
Thanks for the video man. My boat has been acting up for a year. Been stranded too many times. I've gone through new batteries and even changed out the cables. Not getting a charge back to the battery! I have an 04 F115 yamaha. I'm not a mechanic but I love to do things myself if it's within my capability. I think I'll give it a shot since I don't have a grand to give a mechanic lol she's been a pain in my ass.
@WildWonderfulOutdoors
2 жыл бұрын
It's a super simple repair as long as you have the tool. I highly recommend that! You can always bag and tag your nuts and bolts for every piece you take off and lay them in order, so when you go back together its the same order with everything organized. I'm glad the video helped! That's the whole point! Tight lines!
@hookedonthebay3890
2 жыл бұрын
@@WildWonderfulOutdoors one more question brother. How do I know it's not my voltage regulator rectifier?
@WildWonderfulOutdoors
2 жыл бұрын
@@hookedonthebay3890 there is a series of test you can do. I have the data sheet that came with the new stator from cdi. I can send it to you via email or something
@juangallino8206
2 жыл бұрын
@@hookedonthebay3890 Hi, i am having the same problem, battery not charging..What was finally your problem? can you solved it? I have a 60 hp merc, 2016
@hookedonthebay3890
2 жыл бұрын
@@juangallino8206 Hey man I'm taking it to a mechanic in a few weeks. I will let you know when I find out!
@TERRYSMITH-vu6er
Жыл бұрын
CAN A BAD STATOR CAUSE A MOTOR TO LOCK UP WHEN IT DID NOT HAVE ANY PROBLEMS JUST ALL OF A SUDDEN
@WildWonderfulOutdoors
Жыл бұрын
I would think not. It is just mounted to the rotating assembly, not in contact with anything.
@wg7644
2 жыл бұрын
You can use a PISTON STOP to remove flywheel nut too.
@RPHPros
2 жыл бұрын
Thank you for this walk through. Super helpful!
@WildWonderfulOutdoors
2 жыл бұрын
Glad to hear it man! You're very welcome!
@baubljos103
Жыл бұрын
Actually - no. You should check the rectifier first. It's easier to test, and cheaper to replace. Also, take a photo before you start switching wires. You may wanna touch up the spots on the wires that you punctured to test with some liquid electrical tape. Excellent video thx for posting this.
@BigJuiceDevelopment
3 жыл бұрын
When you checked resistance from the coil to ground, isn't it supposed to have read OL. If it measured any resistance, wouldn't that have indicated a bad coil? Just curious.
@WildWonderfulOutdoors
3 жыл бұрын
In the troubleshooting section on the instruction sheet from CDI it says: 1. Check resistance between the yellow wires, you should read 0.4 ohms. 2. Check the resistance from each yellow wire to engine ground, you should not read any resistance. Resistance to ground indicates a bad stator. Remember if you are touching the test leads you will get a high resistance. I appreciate your question, and checking out my channel, I'm trying to hit 1,000 subscribers this year! I got this information right of the instruction sheet that came with part. TIGHT LINES!
@johngilbert3395
Жыл бұрын
Thanks for putting together this video....very helpful.
@WildWonderfulOutdoors
Жыл бұрын
Awesome! I'm glad to hear it!
@MrJunglegem
3 жыл бұрын
Thanks for the detailed and informative video!
@WildWonderfulOutdoors
3 жыл бұрын
You got it man! Glad it helped! Thank you or checking out the channel! More to come!
@jdutch
2 жыл бұрын
So I also need to replace the trigger that is underneath the stator. How do I remove the pin on the trigger safely?
@Tdg-uu6sn
2 жыл бұрын
Torque spec on flywheel nut is 120 ft lb
@WildWonderfulOutdoors
2 жыл бұрын
Ok. I used plenty of ugga duggas.
@InkaOutdoorsTV
3 жыл бұрын
Good video. I was wondering if you can provide the part number for the flywheel removal. Thanks!!
@WildWonderfulOutdoors
3 жыл бұрын
Sure thing man! We used the Marine Tech Tools AMT0023, it works like a charm! www.amazon.com/Marine-Tech-Tools-Mercury-Flywheel/dp/B01N5LJU3N/ref=asc_df_B01N5LJU3N/?tag=hyprod-20&linkCode=df0&hvadid=312114712708&hvpos=&hvnetw=g&hvrand=8349452374840974021&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9009438&hvtargid=pla-583136529987&psc=1
@InkaOutdoorsTV
3 жыл бұрын
@@WildWonderfulOutdoors Thank you!!
@WildWonderfulOutdoors
4 жыл бұрын
If you have any questions, please comment below. Or even just leave a comment if you liked the video!
@SSGSINCLAIR
3 жыл бұрын
Thanks for the informational video.
@WildWonderfulOutdoors
3 жыл бұрын
Glad it was helpful!
@35dhall
Жыл бұрын
Bought a caltric stator .Got a problem it has green an brown wires an 2 yellow.Stock wires are green/white strip an White with green strip an 2yellow wires.not sure how to hook up..Any help would be appreciated
@tattooslm
3 жыл бұрын
I have a 2004 90 horse 2 stroke mercury,when I checked between the two yellow wires, It toggles between.3 and.4.When I checked the ohms between the green with the white stripe and the white I get.681.Also the two bullet connectors from the stator on the two yellow wires have been warm enough that the coating stuck together.The original stator is on the motor and I changed the voltage regulator a week ago because of a high voltage problem.
@WildWonderfulOutdoors
3 жыл бұрын
I can send you the CDI troubleshooting guide.
@tattooslm
3 жыл бұрын
@@WildWonderfulOutdoors Yes sir that would be great,do you want my Gmail adress or can you send it here?
@WildWonderfulOutdoors
3 жыл бұрын
@@tattooslm I can't send photos in comments on here. If you want to leave you're email that will work. You could also message me on facebook or instagram. Once I email you I'll delete your email comment so it's not just hanging out on youtube.
@ugghuggh
2 жыл бұрын
Up to 4 cylinder 660 to 710 between greenwhites should be ok according to manual
@thomasmiller1302
Жыл бұрын
My 60-hp mercury motor is not firing on the top cylinder. What is wrong, and where can I get that fly wheel tool.
@WildWonderfulOutdoors
Жыл бұрын
The tool is on amazon, the part number is in the description. If it is just one cylinder for sure, start with spark and coil.
@angleturner
3 жыл бұрын
A bad stator won’t keep the motor from starting, correct? With no spark, what could be the problem ? Same motor.
@WildWonderfulOutdoors
3 жыл бұрын
We also recently had the volt regulator replaced. It causes similar symptoms to the stator being bad.
@MrGallaleo
3 жыл бұрын
So... 97 90hp elpto here. I have zero spark and zero power getting to the coils. The boat has been sitting for a while. I read that the stator could be my problem... checked it and it's bad from what I can tell. Obviously it needs replacement, but what else would prevent spark after this gets replaced? Oh... and very informative video... I already ordered my tool for this because of this video. Thanks!
@WildWonderfulOutdoors
3 жыл бұрын
Check the battery to make sure it’s charged. Is there a separate coil wire? It could be a bad coil too.
@MrGallaleo
3 жыл бұрын
Battery is good and also new. Don't think it has a separate coil wire. I just checked it at each of the three coil packs. No power is getting to them to fire the plugs.
@WildWonderfulOutdoors
3 жыл бұрын
@@MrGallaleo it might be worth buying 1 new coil and checking if it works, then move it to the other two spots and see if it works there too. Could just be bad coils.
@jguild45
2 жыл бұрын
I've got a 1996 Merc 150 EFI 2-stroke that absolutely quits while at WOT after being well warmed up (20 min of running). I can't go past 7 mph after that happens and it'll start right up after it quits. Hoping for a DIY solution but don't know where to start, ECU, stator, voltage regulators (2). I changed the plugs...no diff.
@WildWonderfulOutdoors
2 жыл бұрын
I just filmed a video a couple weeks ago that I need to edit. This same motor was breaking up at WOT really bad. We ended up replacing a coil that had a loose connection but I think the main problem was a section of wire that we ended up replacing. Check your wiring, on my motor it looked burnt because of all corrosion causing resistance which causes heat. I will try and get that video up soon and I will let you know when it is. You could subscribe too and then you will know when it’s up.
@jguild45
2 жыл бұрын
@@WildWonderfulOutdoors Thanks, Homestand!
@haydenneeson1716
4 ай бұрын
Absolutely orsom boys save a ton of cash
@gilfredooquendo9969
2 жыл бұрын
I'm kinda new at this how can I test the coils with a multi meter how to set the meter and I'm sorry for all the questions 😕
@WildWonderfulOutdoors
2 жыл бұрын
This is the best explanation I could find that is easy to share. www.aa1car.com/library/ignition_coils.htm Check it out and see if it helps you diagnose.
@lebanonbeirut7830
2 жыл бұрын
Amazing video, I feel like a fricken genius!!!! Thank you for your video!!!:)
@leogirardin8356
Жыл бұрын
what happens if you mix up white/green wires?
@WildWonderfulOutdoors
Жыл бұрын
Don't? They are colored for a reason.
@gilfredooquendo9969
2 жыл бұрын
Hi I'm on the process of replacing my stator I have a mercury 80hp but the stator has no part number and I don't want to get the wrong one
@WildWonderfulOutdoors
2 жыл бұрын
Look it up by your model or family number that is on the motor tag.
@gilfredooquendo9969
2 жыл бұрын
@@WildWonderfulOutdoors I have no tag it got destroyed due to a small fire
@WildWonderfulOutdoors
2 жыл бұрын
If you know the year, make and hp then you should be able to find out what model number it is online. Just google it and compare what pops up to what you have.
@gilfredooquendo9969
2 жыл бұрын
By any chance will that stator work on a 80hp? There are so many that I don't know wich one will be the right one
@WildWonderfulOutdoors
2 жыл бұрын
Check your model and "family" number on the factory sticker in the motor. You can search parts by that, the stator I installed was made by CDI, it came with diagnostic instructions and instructions to install. Very high quality products from them.
@129skeeter
3 жыл бұрын
Would the stator prevent my outboard from going over 4 rpm. Max is 5600
@WildWonderfulOutdoors
3 жыл бұрын
No, it just attaches to the flywheel. It’s not it’s own moving part. I would check carbs and fuel filter first. Does it bog down or just not rev to 5600. If max is 5600 you probably wouldn’t run it that high anyway. That would be like keeping your car at redline going down the highway.
@tojadmka
3 жыл бұрын
Would you be able to show a short video how your trigger is mounted? I got the service manual for my 40HP Mercury and even there they don't show it step by step
@WildWonderfulOutdoors
3 жыл бұрын
What do you mean by trigger?
@tmpst787
2 жыл бұрын
@@WildWonderfulOutdoors the trigger assembly that goes under the stator, it actually looks like yours might be loose
@WildWonderfulOutdoors
2 жыл бұрын
@@tmpst787 What makes you say that?
@tmpst787
2 жыл бұрын
@@WildWonderfulOutdoors it’s the circular plastic piece that ends up in the center of the stator. It’s mounted by a plastic arm that sticks out to the left of the stator and I see it move around when you touch it. It shouldn’t be moving around like that.
@tmpst787
2 жыл бұрын
@@WildWonderfulOutdoors at 7:09 when you pick up the old stator there is a part sitting around the shaft that moves around a little as you pick up the stator, it kind of looks like a smaller stator, that’s the trigger and I’m pretty sure it’s not supposed to be loose like that.
@amyerwin1093
Ай бұрын
Great video tx u
@taylornash172
2 жыл бұрын
Do you have to take flywheel off to take starter off?
@WildWonderfulOutdoors
2 жыл бұрын
No you shouldn't have to. Maybe just the flywheel cover.
@fowvee
3 жыл бұрын
Were there stainless steel flat washers under the plastic wingnuts that hold the flywheel cover on?
@WildWonderfulOutdoors
3 жыл бұрын
Not that I remember.
@WildWonderfulOutdoors
3 жыл бұрын
Come to think of it, possibly.
@andrewaucoin276
2 жыл бұрын
What was the stator part number for the new one you installed?
Can I ask what the issue was you were having to what led you to change the stator? Also you mentioned voltage regulator
@WildWonderfulOutdoors
Жыл бұрын
Misfires, poor idle and really couldn't run at low rpms for no wake zones, moving around the ramp. There was more to be found, this was years ago I have a new video I am working on where we find a culprit that definitely helped exaggerate those issues.
@joshbirtchetfishing5196
Жыл бұрын
@@WildWonderfulOutdoors I'm having por idle and starting along with getting up to speed.
@WildWonderfulOutdoors
Жыл бұрын
@@joshbirtchetfishing5196 Starting as far as? You're using the choke on the key I'm assuming. The cheapest part to throw at it to start is a fuel filter and some stabil to make sure the gas is good.
@joshbirtchetfishing5196
Жыл бұрын
@@WildWonderfulOutdoors no I don't use the choke. 98% of the time starts right up. But lately not so much or I'll be idling and then it just dies runs rough and can't go above 30 mph. I check the plugs they did not seem burnt but did have a lot of oil and gas on but yes I will do the fuel filter
@Honda1k
3 жыл бұрын
Should have used loctite on your bolts to hold on your stator
@WildWonderfulOutdoors
3 жыл бұрын
I guess, it didn't have any on there from the factory.
@brandonwood7973
2 жыл бұрын
Does this affect engine timing at all?
@WildWonderfulOutdoors
2 жыл бұрын
No, the flywheel has a guide pin on the crankshaft. So there is only one way to put it on.
@fje137
3 жыл бұрын
Greetings, does it matter how many amps the stator brings? I'm in the market for a new stator but I keep seeing different amps 9 amp and 16 amp. Its for a merc 75 hp 2003 2 stroke.
@WildWonderfulOutdoors
3 жыл бұрын
We called a local marina and gave them our model number and they ordered the part. We went with a CDI electronics stator. It is "aftermarket" but it is like ac delco to GM. They make the part for the OEM. I would at least call a local dealer and have them tell you which one to get. Also order your flywheel puller!
@bouldernelsonbigfoot
2 жыл бұрын
thx
@WildWonderfulOutdoors
2 жыл бұрын
No problem man! Hope it helped!
@gilfredooquendo9969
2 жыл бұрын
I just subscribed to your channel maybe you can help me pinpoint my problem I have an 80hp mercury outboard motor oil injected that starts but I'm only getting spark from one of the 3 coils and I don't know where to start
@WildWonderfulOutdoors
2 жыл бұрын
Have you moved coils and plugs around yet to see if they work in different locations?
@gilfredooquendo9969
2 жыл бұрын
@@WildWonderfulOutdoors no I guess that will be my start
@WildWonderfulOutdoors
2 жыл бұрын
@@gilfredooquendo9969 yea man do that just to eliminate if the parts are bad themselves or if it is something beyond that. I appreciate the support man! I am getting ready to film a new troubleshoot/repair video on my outboard.
@gilfredooquendo9969
2 жыл бұрын
Will that puller fit my mercury 80hp?
@WildWonderfulOutdoors
2 жыл бұрын
Does it have threads in the top? When I bought it, it said it was for multiple models.
@gilfredooquendo9969
2 жыл бұрын
@@WildWonderfulOutdoors yes it does do you have the link to order it
@WildWonderfulOutdoors
2 жыл бұрын
The link is in the description of the video.
@christophercharles8273
4 жыл бұрын
Hi, i would like to have a copy of the CDI troubleshooter please
@WildWonderfulOutdoors
4 жыл бұрын
If you have instagram send me a message and I will send it to you. I don't want to ask for your email on youtube haha. @wildnwonderfuloutdoors_
@donturner3155
Ай бұрын
You don't know how to read a Volt/ohm meter apparently.. O.L. is NOT ohm overload...it means no resistance or open wire...what a waste of time here
@jonathanmartin7003
3 жыл бұрын
Do you have to reset the timing after doing this?
@WildWonderfulOutdoors
3 жыл бұрын
No sir, the flywheel is notched and the crankshaft has a pin that only allows it to go in one spot. So the balance or timing never changes. If you get the tool it's super easy.
Пікірлер: 114