I'm in the process of removing three layers of peel 'n stick tiles. A nightmare, but I used what I had on hand which was a hairdryer. I set it on "hot" to soften the glue. It works very well and is much faster than an iron. I was able to lift all three layers at once. A heat gun would be best, however. Don't even try to get it up without heating it.
@275MsParis
Жыл бұрын
Thank you very much it’s working
@abigail1023
Жыл бұрын
@@275MsParis Glad to hear it!
@aboren8096
Жыл бұрын
The blow-dryer will probably make it a lot easier as you get under the area closest to the cabinet! I will try both ways. Thank you everyone!
@abigail1023
Жыл бұрын
@@aboren8096 Once you pry up a corner, just keep the heat aimed directly between the tile and the floor as you push the putty knife (a wide one works best) further under the tile. Unless you're lucky, there will probably be thick, sticky glue left on the floor. There are ways to remove it but it was too hard for me so I just left it until it dried. There was no problem getting porcelain tiles installed on top without glue removal. Good luck!
@aboren8096
Жыл бұрын
@@abigail1023 that sounds awesome. I will do the same. Thank you for the tips!
@mariazamora5646
2 жыл бұрын
So this peel and stick tile is in the kitchen? Wow! This kind of video is what I needed. I’m going to get myself some for my kitchen
@Sharkskinm
2 жыл бұрын
So what's the best way to clean under it if you wanna put down something else?
@kittyroe8136
Жыл бұрын
WD40 and a scraper will remove the sticky. After you’ll have an oily residue from the WD40, so you’ll sprinkle some flour and rub it in until it absorbs the oil residue.
@deborahbraswell4665
8 ай бұрын
@@kittyroe8136learn something new everyday 😊😊😊
@tortoisemech2993
3 ай бұрын
Is there any chance it contained abestos?
@jabster58
Жыл бұрын
Did you have it tested for asbestos
@courtneymacdonald2196
Жыл бұрын
need to remove old tiles that have been here for YEARS before i moved in (10years ago) so longer than 10 years, only getting up chips & corners, definitely trying the iron since i need to do my entire bedroom
@fairyfreak63
2 жыл бұрын
A blow torch, I've seen, removes tiles faster, but, I do dig, this tip, with the iron; thanks. This Is actually safer. For faster removal, the blow torch, I've seen them come right up, one by one.
@AtHomeDIY
2 жыл бұрын
Yeah, for the average home owner I'd probably recommend sticking with an iron for safety reasons haha. But I can see how a blow torch would work quicker, I would even use a heat gun before a blow torch and probably get a similar result. Cheers!
@OldSoulKare
7 ай бұрын
What about the sticky residue ?
@alphafit2057
Жыл бұрын
How to clean the floor after peeling the whole floor before putting down a new one?
@James-oy9no
3 жыл бұрын
Wow incredible! My next project in my bathroom! 👍👍👍👍👍
@Clovergirl7934
2 жыл бұрын
How did you get the adhesive up?
@miamiwax5504
2 жыл бұрын
Goo gone would probably work
@linda5420
2 жыл бұрын
Here's a video on how to remove the adhesive after picking up the tiles. Using baking soda..kzitem.info/news/bejne/u4Kwn2mYq3N3h5w
@ems8717
2 жыл бұрын
Omg thank u i looked at the other videos and they peeled of easily but mine where like ur tiles so def trying this
@ẞæmǐø
7 ай бұрын
Thank you so much. 🙏
@yyanngg9515
Жыл бұрын
You're really helpful, glad i found you hehe
@teebaby7387
3 жыл бұрын
Thank you so much!
@meme-ed8nr
Жыл бұрын
Thank you-very helpful!
@jasonharris4926
Жыл бұрын
Thank you
@thecitizenjoan
2 жыл бұрын
Sliding a butter knife underneath it is helping me too
@NerakGreen
Жыл бұрын
I have layers upon layers of peel and stick glued to bare slab in my basement. Sellers didn’t disclose foundation damage or their repairs and BB&T won’t let me borrow on a loan I paid off halfway by 7 years and 4 months when I found the undisclosed damage. I can’t afford a sump pump! Not after replacing the HVAC/AC after the first 2 years. I have a heat gun and I seriously doubt ima burn through solid concrete. If so, I’ll paint it smooth. I’m gonna try heat with my scraper, maybe water too. Every 2-3 years, I go in my basement to find my stuff floating in rain water. I sure wish them tiles would float! I didn’t ask for this and I certainly didn’t consent to it. Life, man. Merit and honest sweat be damned, it’ll stick it to ya anyway.
@tagpopper4520
2 жыл бұрын
Thank you!!!!!
@pasxalitsapasxalidou4720
Жыл бұрын
i have something similar in my kitchen and i've read it might contain asbestos. Is this the case with this one? Did you have that examined? i am so terrified of removing mine..
@tortoisemech2993
3 ай бұрын
Did you ever get it tested? I'm in a similar position.
@ronnie_j91
8 ай бұрын
This would take all day for a whole room
@georgec9765
Жыл бұрын
why don't you use a heat gun (750F)
@zivaschen464
2 жыл бұрын
you dont have a heat gun?
@AtHomeDIY
2 жыл бұрын
I do. Heat gun would probably work just as well, great point.
@philipbottrill8450
2 жыл бұрын
What with the shirt? Lino coming off isnt it?
@AtHomeDIY
2 жыл бұрын
Lol, very true. I guess just to keep the surface of my iron clean.
@jason-sonyafontenot4039
2 ай бұрын
I hate steel and pick tiles!!!!!
@otnim
11 ай бұрын
I used the girlfriends hair dryer it's a lot quicker than the iron method. 😂
@valeriezoe1
3 жыл бұрын
Using parchment paper, something bakers use, in place of cloth to keep the iron from contacting the surface of the tile, will provide just as much protection for the iron while allowing more heat transfer. It worked well for me and I used the iron at the full heat setting.
@AtHomeDIY
2 жыл бұрын
Great tip! Thanks for adding that!
@paganpoetprophet6441
2 жыл бұрын
Very cool I tried it and it worked
@mcuz2164
2 жыл бұрын
Came here to say the same thing
@aj2964
8 ай бұрын
Thanks!
@bobsblackwell3594
5 ай бұрын
Thanks all x
@deborahbraswell4665
8 ай бұрын
Just tryed using the iron trick to remove peel and stick tiles in my bathroom and it did the job really fast. Thank you. Will be using this trick for removing old peel and stick tiles in my kitchen😊😊😊
@GZUS316
Жыл бұрын
Steal and pick.
@hectora3692
Жыл бұрын
Well that looks much better and easier to lift the linoleum floor tiles . When you heated up with the Iron 👍 that is a safe way to do it . Another guy was showing how to do it and he had propane torch to heater up the tiles and he recommended to have fire extinguisher near by and garden water hose in case you start a fire that is extremely danger specially if the subfloor is plywood not concrete you be inhaling the toxic fumes or 😩 you can have your house bursted in flames then you will wind up without restroom and the house burn to the ground 🥲 ☹️ 😖
@lupe55775
Ай бұрын
How do you remove the stickiness from the floor?
@Jimmy_Cavallo
2 жыл бұрын
💥 Great tip thank you. Any suggestions on what to do about the sticky residue left behind.??
@icecreamladydriver1606
2 жыл бұрын
That is the same reason I am here.
@johnyridermx2382
2 жыл бұрын
Use an adhesive remover, just let it soak for an hour and scrap it easily
@H1ana2digital
3 ай бұрын
White Spirit works well!
@H1ana2digital
3 ай бұрын
White Spirit works well!
@GreatMindsSeekTruth
19 күн бұрын
WD40 then sprinkle flour to absorb the oils after.
@joedevitto6113
2 жыл бұрын
So much easier , wish i saw this before removing a few tiles i needed to get up and replace. thanks for sharing ~
@xXSeak
Жыл бұрын
What do I need to do in a case where you put modern peel and stick vinyl tiles on normal tiles and you don't want to ruin the normal tiles beneath while removing? (I'm renting and want to put modern PVC tiles on real ones but maybe once I move out the owners asks me to remove them)
@DosBear
8 күн бұрын
Thanks, that's just the advice I was looking for but I would use parchment paper as suggested by the commentor below.
@randaldavid7685
2 жыл бұрын
Here's another tip. Empty the clothes drier, use a separate article of clothing for each tile. You have now completed two tasks at once, tile replacement and the laundry ironing, your wife will love you for it.
@AtHomeDIY
2 жыл бұрын
Brilliant! That's some "two birds with one stone" thinking right there.
@keoshap1388
10 ай бұрын
😂😂😂😂😂
@Queen_62
5 ай бұрын
😂😂😂😂😂
@rainbowintheclouds6811
8 ай бұрын
Can I use an iron on a layer of stick in tiles that were placed on top of an already Lino floor? Old fixer upper with lots of surprises
@carolberridge6102
18 күн бұрын
Thank you so much! Clear explanation and efficiently presented. All the best!
@JakeFranklinFB
5 ай бұрын
Watching this video after spending 3 hours getting off only a few “tiles.” I hate these!
@julieowen4015
2 жыл бұрын
Thank you for this, will use your tip to remove the rest of my tiles
@tomzy01
Жыл бұрын
How do you get the glue off cause I’m worried about removing all the tiles and it leaves the floor sticky
@lindywheeler4192
4 ай бұрын
I used a heat gun to remove the tiles, but we did the whole kitchen, it was much quicker.
@markbishop6
3 жыл бұрын
Steel and pick linoleum tiles? :40 Good video though...great idea...can't wait to try it!
@pixelrabbit261
2 жыл бұрын
Life saver!
@juanconde9828
2 ай бұрын
Heat gun is the best way then use a adhesive remover 👍👍
@natmuchthere
2 жыл бұрын
Can the sticky tiles damage the floor?
@ericmedinamedina6219
Жыл бұрын
Would a hair dryer work??
@visumexcipio
3 ай бұрын
Cool!
@deewademai
3 жыл бұрын
what about the sticky think on the subfloor? How do you remove those?
@AtHomeDIY
3 жыл бұрын
I honestly just let it dry and ware off over a few days. But you could probably use a product like Goo Gone to get it off.
@icecreamladydriver1606
2 жыл бұрын
The question nobody has answered for me is what do you do with the sticky floor? I want to put down new tiles but the floor is so sticky and there are dirt lines in the creases. Thanks for the video.
@AtHomeDIY
2 жыл бұрын
Hi! I just did a quick search on KZitem. There is a video by "Got it Made" about removing adhesive that has really great feed back in the comments. For myself, as I worked in the area doing other projects, the foot traffic and dust just eventually wore off all the stickiness.
@icecreamladydriver1606
2 жыл бұрын
@@AtHomeDIY Thanks.
@mikeperry3236
Жыл бұрын
@@AtHomeDIY remo
@marthalampropoulou
4 ай бұрын
Hello very good video you are giving me hope that I will get rid of them What about the glue underneath though any tips to get the floor clean ? Will it’s all melt with the iron ?
@beautifullybusymom9672
3 ай бұрын
Thank you so much! I've been working for hours and was SO OVER IT. This works wonders!
@cameronkey-slater6995
5 ай бұрын
My question is does it leave behind residue if so how do I do away with that without damaging the flooring underneath laminate
@annaschrock9728
2 жыл бұрын
does it also remove the glue on the subfloor? cause right now i pull a tile up and it is still stick on the the subfloor.
@tonyhdj3172
Жыл бұрын
Thanks great idea what about using my father-in-law‘s heating gun?
@sherryevans9797
3 ай бұрын
You saved my life!!!!! Thank you from my ❤
@SHAROD312
Жыл бұрын
That’s still a long process it has to be another way
@sharonstubbs8248
2 жыл бұрын
Thank you, Thank you for sharing. I will be trying this on Monday!
@brenda1braun
Жыл бұрын
I used my steam mop and it came right off .
@pozitivautluk
4 ай бұрын
Very helpful! Thanks
@yennygutierrezrodriguez6577
2 жыл бұрын
¡Exceleeeeeeeeeeente bravisimo!... 👏👏👏👏👏👏👏👏👏👏👏👏
@noiseguru3981
2 ай бұрын
Tanks Buddy!
@JaimeGarcia-pe7bj
8 ай бұрын
What about a heat gun?
@MrNathan791
16 күн бұрын
My kitchen floor linoleum is starting to break off in chunks. I thought it was gonna be a very slow messy process in taking it all up. Your suggestion of using an iron, and cloth was so helpful to me. I now feel very confident that I can take it up and put down a new slip proof layer. Thanks for sharing. Peace Out.
@mnruxpin
7 ай бұрын
awesome thx
@valeriezoe1
3 жыл бұрын
As far as the heat level goes, it sounds like it's trial and error. You're saying to start at 75% and go from there I guess.
@AtHomeDIY
3 жыл бұрын
The goal is to warm up the glue under the tile. Go as hot as you'd like, if it doesn't seem to be working, go hotter. I'm sorry, I don't have specific numbers for you.
@valeriezoe1
3 жыл бұрын
I didn't hear any mention of how hot you heated your iron. I'll assume you put it up as hot as it can go, right?
@AtHomeDIY
3 жыл бұрын
Good question, I think I heated it to like 75%. Hot enough to melt the glue.
@ponyony9621
2 жыл бұрын
Thank you
@deebadley6708
3 жыл бұрын
Thk you 😅
@schmellymely6831
2 жыл бұрын
Awesome! Thank you for the pro tip!
@lyttonpage8879
2 жыл бұрын
Great tip, thanks for sharing. I’ve read that these type of tiles may contain asbestos?
@Jimmy_Cavallo
2 жыл бұрын
Usually the size indicates if they are asbestos or not. If they are 9x9 inch square and they were made between 1950 - 1980 they are most likely asbestos.
@farrahslim6701
3 жыл бұрын
Thank you
@kimberlyguardipee4070
2 жыл бұрын
useing a steamer may be faster I would think.
@AtHomeDIY
2 жыл бұрын
Anything to heat the glue and you should be good.
@SunFlowersCutie
3 жыл бұрын
Perfect, all the current tools I have to do this. Thanks!
@AtHomeDIY
3 жыл бұрын
Actually just finished doing the rest of this floor yesterday and an oscillating multitool also worked well for this. Good luck!
Пікірлер: 125