I used a 3" hole saw for my triglide with oil for cutting took about, 3 minutes each side: then installed the Thunder Torque inserts for reversion... sounds great and runs great!
@Borel-nv5bq
5 жыл бұрын
Best part of the video is listening to the camera man breathe
@dalesimmons976
4 жыл бұрын
Let's see the right side ... I love it when people show half of the job... It's probably because he didn't have the capability to do the right side...
@mikeanderson6422
3 жыл бұрын
No finesse there, what a hack, im sure the paint got whacked.
@no1but24
8 жыл бұрын
So I done this to my 2015 Road Glide Pros, sound amazing and only 20 minutes of work very easy. Cons, loss of low end torque do to no back pressure, Catalytic converter is during a bluish purple color, it pops every so often do to be ending lean, it seems O2 sensors didn't recalibrate air/fuel mixture, I don't recommend doing this save up for pipes.
@larryblakeus
5 жыл бұрын
Thanks for the video man. I know it's a few years old but still helpful. I just did this to my 2019 Road Glide. 30 minutes and both sides were done. Not sure why people are be bitches about the right side pipe. It was the exact same as the left. Thanks again bud!
@11123DRUMMER32111
5 жыл бұрын
LBCSG17 I think some people are confused about older models. I believe 2017+ M8 exhaust is the same on both sides. I believe the other guys are thinking about the Twin Cam setups.
@smilysbable
3 жыл бұрын
Did you feel any lose in power in your bike ??
@smilysbable
3 жыл бұрын
I m thinking about saving money and doing my removal of catalyst converter 2020 road glide special
@jaymood6607
2 жыл бұрын
You made that look super easy... Imma try that
@txpsfn
7 жыл бұрын
One problem. You didn't show how to remove the right baffle. You and I both know it's a completely different process so why don't you make a video on the right side to show the difference.
@armycece
6 жыл бұрын
James Collier I just did it on my 2015 road glide and I had the same baffle as the left on my right but I know what you mean about the big baffle on the right side
@gutierrezc8709
5 жыл бұрын
thanks for adding another video of what we already know how to do. show your take on the right side; that's more interesting.
@wilfredoamaya2023
5 жыл бұрын
yup you right
@ILikeWetVaginas
3 жыл бұрын
I just did it on my 2020 street glide they both slid out and I did it with a electric drill at that in about 25 mins
@robertmills4101
2 жыл бұрын
@@ILikeWetVaginas any loss in power removing the baffles or did you add a Fuel pak kit to adjust motor to pipes ??
@toradog5719
7 жыл бұрын
Hmmm, must be pretty loud. I just drilled a bunch of large holes around the baffle and like the sound. Maybe a little too subtle for some.
@krogersucks45
3 жыл бұрын
A Dremel with a metal cutting blade will work if you done have a die grinder. Funny how ppl always do the left one , there's a reason the right side ( on Twin cams) is different and more difficult
@boblafountaine9560
3 жыл бұрын
I like the videos when they show what really happens when you run into problems. You don’t get caught off guard if they’re being realistic in their videos.
@dickyfisher9249
6 жыл бұрын
Have '01 Heritage with stage 1 kit. An 2 into 1 Screamin Eagle exhaust. The baffle n guts are held in by a Single Screw underneath. I pulled it all out. But lost power cuz No back pressure. So i cut the baff. in half an reinstalled it. Sounds fkn awesome an i got Not only power back but it Runs way better in performance too.
@chopperman8042
4 жыл бұрын
Mines 07 heritage, same thing. Just one bolt.
@89bassmaster
5 жыл бұрын
Damn that guy recording needs a inhaler!! He was breathing so hard I thought the bike was on for a minute there! Just kidding I’m just being an ass, great video thanks!
@coffindancer38
3 жыл бұрын
Why dont you get an extension and a set of "christmas tree" drill bits, and drill out the baffle to the diameter that gets you the sound you want?
@trmoore57
8 жыл бұрын
add a lollipop to make up for low end like on the old dirt bikes just a washer welded to a bolt an its tuneable hahaha works great on a 09 flhx
@danoc5215
6 жыл бұрын
thanks, took me 15 min, sounds way better.
@hughkaplan5128
5 жыл бұрын
Pipes turning blue or popping. It's running lean. I would suggest remapping. If you have the credit card type fuel adjuster, enrich with more fuel.
@dre.vil4958
7 жыл бұрын
why the camera man breathing so damn hard lmao
@bskee001
6 жыл бұрын
Because he's getting so excited in anticipation for how badass that bike is gonna sound once they're done...
@Russcles
8 жыл бұрын
Now do the right hand side.... a little more difficult ain't it?
@canamnate1
7 жыл бұрын
Russ Ball there is no difference in the right or the left side. They are both the exact same. Whoever told you they are different is a jackass lol
@paulbicket1127
7 жыл бұрын
Nate Mitch the right side is more difficult
@nicvanorton6795
7 жыл бұрын
Russ Ball The right side has a fitting that needs to be compressed/crushed in order to be removed. Much more difficult than left side. There are videos on here that demonstrate that.
@JCMontes16
6 жыл бұрын
Yes it is . The right one has a balloon configuration that require several cutting and then crushing to let it out.
@volunteerpatriot2143
6 жыл бұрын
kzitem.info/news/bejne/1qmM046FiZ5_ZH4 Take a look Nate. Now, who's the jackass?
@christopherfisher123
2 жыл бұрын
Why didn’t you do the right one?is that right side different then the left?
@darrellcarter4143
4 жыл бұрын
You are good , try the right side now and see how much fun you will have
@wood-b7869
6 жыл бұрын
I was looking to have trouble on my right pipe and it came out just as easy as the lift one. I was looking to have trouble. 2015 street glide special.
@michaelmemphis2705
3 жыл бұрын
I wanna hear how loud it is ??
@218422100
7 жыл бұрын
that sides easy...the right sides metal baffle is shaped differently and harder to remove.
@aaronchandler8141
Жыл бұрын
That's how you remove a baffle on the left side, right side is a bit more difficult
@StricklandOffroad
9 жыл бұрын
We noticed a gain in power through the whole rpm range the smaller piping coming off the engine gives you enough back pressure you could weld them back in but you will be welding on the pipe thay is chrome on the other side so you will get color change
@coffindancer38
3 жыл бұрын
There is no way in hell you gor more power from that motor by taking out the baffles. Think for a minute. Ther is no chance harley designed an exhaust system that chokes power out of their product. You think it has more power becuase its louder. Not a chance.
@JCMontes16
6 жыл бұрын
The title should be different! like: HOW TO REMOVE THE LEFT STOCK BAFFLES ON A HARLEY DAVIDSON
@criznitty
3 жыл бұрын
That right one tho 😂
@milesonwheels8127
2 жыл бұрын
What about right exhaust?
@kevinakles8460
Жыл бұрын
Face shield lol. Nice video ty
@JayGraphix
9 жыл бұрын
I have a 13 Street Glide and am interested in removing the baffles in the stock pipes, but everywhere I read, they are all saying they are losing low end torque. But, your saying you gained a bit of power ... Any thoughts?
@Walt450
3 жыл бұрын
Doing this you loose back pressure so that means you loose hp unless you retune
@AdmiralRustyShackleford
8 жыл бұрын
Why not leave the packing in? Probably has a deeper, cleaner sound to it. Besides, over time I bet it burns out anyways so might as well enjoy the cleaner sound while you can. Or you can get more sound by taking the mufflers off and removing the packing from the back to leave the baffles in place, get more sound that way but not be stupid loud with empty pipes.
@mrlookuphigh
6 жыл бұрын
What do you have to do after removing baffles? Is there any replacement of sensors, or changes in the engine?
@softailslim7146
2 жыл бұрын
Hello there … if i remove my baffle from my 2 into 1 pro pipes n run it that way , would it mess up my exhaust or will it be ok ?
@anemasherun
3 ай бұрын
How does it sound?
@bubbaknowsstuff
3 жыл бұрын
That was the easy part now remove the right side. Totally different animal
@mrpayne1981
8 жыл бұрын
Do you think this is the same process for the stock pipes on my 2004 Road King?
@siilveronyx2324
7 жыл бұрын
will it not mess up the mapping and tuning on the fuel injection
@046642
9 жыл бұрын
Just wondering if you could remove the packing from muffler then weld the baffle back on for back pressure? And still get sound but not suffer low end power
@LaBestiaHumanaMX
9 жыл бұрын
046642 How much low end power is actually being lost? I removed the baffles on my Softail Breakout, and didn't notice the loss of power.
@ericdanaher6652
2 жыл бұрын
wtf was the hammer for
@starrider1900
8 жыл бұрын
pretty sure this will void the warranty
@LR-em8ne
5 жыл бұрын
lets see the right side done bud! lol
@Kornpop45
6 жыл бұрын
So will this void my warranty
@bhouse726
8 жыл бұрын
Does the ecm have to be remapped after you do this?
@bullsquat2695
8 жыл бұрын
No, You can just Tear the ECM Outta There! Also any time you see wires and stuff on your bike, YANK THEM OUT by the roots, cut them with wire cutters etc. Anything Just Cut And Remove All Wires From the Bike. Go for the CLEAN LOOK.
@TheRooster1122
7 жыл бұрын
Do the right side now buddy!!!
@joeljimenez8560
4 жыл бұрын
Pro-Tip: Use real eye protection and not just corrective eye glasses. Imagine losing an eye due to something that easy.
@arthurmadaris5113
4 жыл бұрын
Dude,chicks dig a one eyed guy
@bob6168able
8 жыл бұрын
Would it be possible to remove the baffles from only one pipe and leave the other as is to get moderate sound level. .? or this will make pressure on one side of the engine.
@StricklandOffroad
8 жыл бұрын
you could as long as your bike had a y pipe
@bob6168able
8 жыл бұрын
+jerry strickland Thanks man.
@21damand
9 жыл бұрын
Do you have video of pipes after removal ?
@StricklandOffroad
9 жыл бұрын
just what is in video just that baffle is gone nothing on the outside
@jinxgtr
6 жыл бұрын
now right side.!
@rodrigolaureano
7 жыл бұрын
right side ?
@Nonameatoll
4 жыл бұрын
So what if you want to put the baffles back in?
@StricklandOffroad
4 жыл бұрын
You would have to replace them i would not suggest trying to go back
@MarioSanchez-yd9wy
4 жыл бұрын
Why is the man on the camera breathing so loud??
@TexasDave1836
8 жыл бұрын
lol why didnt you do the right side? not the same as the left
@StricklandOffroad
8 жыл бұрын
we did do it the same I just didn't feel like recording the whole thing I would presume people to be smart enough that we did
@TexasDave1836
8 жыл бұрын
Oh im 100% sure you did cause why wouldn't you. Im just saying taking the baffle out on the right side its not the same as the left. "Not as easy"
@blkstdpoodle
8 жыл бұрын
It's just the same as the left side...I just did it last week. I used a Dremmel with little cutting wheels and it worked fine.
@r6erbuyafool
6 жыл бұрын
I haven’t seen any videos of the right side being done on a 14 or newer. I wonder if they are the same now. The pre 14s have that extra piece on the right from what I’ve seen.
@lmdetect
7 жыл бұрын
Well fucking duh, now help these folks out with the right side.
@paullion3763
3 жыл бұрын
Everyone videos the left side seems easy 'Til the right side which is a bitch to do.
@raesimpson2177
4 жыл бұрын
what about the right hand side one ??????
@StricklandOffroad
4 жыл бұрын
We only did one side so it was half cool lol. It was the same process as the left.
@raesimpson2177
4 жыл бұрын
from what I understand the right hand side is a lot more difficult to get the baffle out due to it being larger in size so can you make a video for extracting the right hand side baffle???
@Westernchauvinist
Ай бұрын
Did this now my bike back fires
@CajunHarleyRider
5 ай бұрын
Not for a 2023 street bob... cut loose wont come out
@JC-ze6hj
3 жыл бұрын
What about the right side. That's the pain in the ass side
@roadkingglider4683
7 жыл бұрын
Does removing the baffles decrease performance, HP, and are they responsible for the needed backpressure?
@StricklandOffroad
7 жыл бұрын
Road King Glider the baffles do hold some backpressure we did gain in low end power
@roadkingglider4683
7 жыл бұрын
jerry strickland so... the setup in the video is purely just baffle and insulation removal? That slanted end piece, what is it and does it need to be welded back in place?
@StricklandOffroad
7 жыл бұрын
Road King Glider we didn't weld nothing back in left the metal and fiberglass out
@roadkingglider4683
7 жыл бұрын
jerry strickland - thinking of doing this to my 2015 Indian chief.... Your thoughts..?
@StricklandOffroad
7 жыл бұрын
Road King Glider that's a nice bike the pipes should be very simular just be careful to only cut the inside metal it's very thin
@rickygutierrez6023
7 жыл бұрын
Now show us all how to do the right side . Hahaha
@benjohnson3700
8 жыл бұрын
you want your bike to run hot, do it
@canamnate1
7 жыл бұрын
jackson j No it doesn't run hot hahahaha some of you guys and your thought are so classic.
@rhbobbyfast2
8 жыл бұрын
Did yhe bike need to be remapped?
@StricklandOffroad
8 жыл бұрын
no we didn't
@cliffodell7417
4 жыл бұрын
i would probably buy some slip-ons or new pipes instead of taking a grinder to a 20 thousand dollar bike...
@jhask64
Ай бұрын
Right side, right side…. bunch of cry babies. Oh, did I forget to mention the “right side?” Good video, thanks.
@ErnieSesameStreet
7 жыл бұрын
No safety concern
@cdsouthern
5 жыл бұрын
"How to remove a baffle... and get lung cancer". Dudes, wear a mask instead of breathing in that fiberglass dust.
@arthurmadaris5113
4 жыл бұрын
Pussy 😆
@stevepp9457
6 жыл бұрын
Always taking the easy way out....
@mikejohnson7202
7 жыл бұрын
You shouldn't have done that. Messing with a Harley. If I see you on the street your're going to get your ass kicked.
Пікірлер: 113