Thanks! This method worked great for me. No need for a blow torch or hacksaw. For my Delta 600 series bonnet nut, I found that I needed to use a Fernco 2" x 1-1/2" connector. The clamp on the 2" x 2" size was too large for the nut, and I couldn't tighten it down enough. The 1-1/2" connector side slipped on as I pushed it onto the nut and rotated it a bit.
@BruceLeef
3 күн бұрын
Does length of the 2 inch pipe matter.. ? How long should it be ??.. Thanks
@mikel.6209
3 күн бұрын
I'm not a plumber, but I think any length that gives you a good grip is sufficient. The key to this technique is the collar that is tightened down with a screwdriver. It establishes grip around the entire circumference of the bonnet nut. The longer the pipe, the more torque you would have. But you shouldn't need more than 6 inches, I would think.
@BruceLeef
4 күн бұрын
..just got home from the hardware store with a Saw.. 😭🤣 let's try this.. be back soon with the results.. thank you 🪚
@billrodgers2830
18 күн бұрын
It worked!!! Thanks a bunch!
@nosonfontenot3072
4 ай бұрын
Dude, that is awesome! thanks!
@AveryThePlumber
4 ай бұрын
Glad it helped!
@Dontbeeadummy
4 ай бұрын
U sir are a gangsta!!!! Amazing stuff. Thx brody.
@AveryThePlumber
4 ай бұрын
Glad it helped my friend! I like to think I’ve got some good tricks up my sleeve lol
@jdcisneros9023
4 ай бұрын
That was dope thanks bro
@AveryThePlumber
4 ай бұрын
I’m just glad it works and helps!
@patrickwilson9833
4 ай бұрын
That's awesome thanks for the knowledge
@AveryThePlumber
4 ай бұрын
No problem!
@BlueDuck211
20 күн бұрын
Dude, awesome…..did you try a strap wrench first?
@AveryThePlumber
12 күн бұрын
I have not! This was what I had and it’s always worked for me lol
@tannerwest6823
2 ай бұрын
Hit it with that Raptor 6 in 1
@jaydrains2247
4 ай бұрын
LoL.. as a plumber thats bull sh*t.. ive put wrenches on that and now a fernco with pvc attached removes it , yeah ok , get a dremel tool and cut it off
@AveryThePlumber
4 ай бұрын
Try it out then get back with me. I’m a plumber too, it’s a life saver. When you put wrenches on that brass nut it causes it to oval from force being applied on two sides. With a fernco and hose clamp even pressure can be applied 360 degrees around the bonnet nut, allowing for it to come off easily
@jaydrains2247
4 ай бұрын
@@AveryThePlumber ok i will definitely try it , i keep an extra bonnet on the truck just in case. Lol
@AveryThePlumber
4 ай бұрын
@@jaydrains2247 I always do too! Trust me, I get it lol it doesn’t work 100% of the time but a solid 90%. You’ll wish you knew it sooner
@kennethjacobs2875
2 ай бұрын
How about a strap wrench?
@christopherlogan7296
2 ай бұрын
Hell Nawl I call BS I damn near broke the valve body trying to get that ring off no way I Dnt believe it 🤣🤣🤣
Пікірлер: 24