to note if your having problems trying to remove the spools from these one reels i forgot to mention you have to make sure you have to loosen the drag up to its lowest setting before you can properly remove the the spool do this step before you remove the c clip from the drag washer on top of your spools because if you don't you won't be able to remove the spool from this type of reel sorry i for got to say this in my video because i lost that part of my video when i removed the spool i ran out of space on my sim card i apologies for that uses a screw driver to remove the c clip retaining the spool in place and pull the drag washers off with the plastic washer as well
@terrymarsh8742
2 жыл бұрын
wow,you make it look so easy,I need to service mine because it is just about froze up.
@LlamaMonster
3 жыл бұрын
Nicely done!
@andrewhondo
3 жыл бұрын
Thanks!
@garrettlauzon1656
3 жыл бұрын
If you ever want a good tool to apply grease, a small flathead screwdriver works well. Then, you don't have greasy fingers. Just my tip. Great video as always, Andrew
@andrewhondo
3 жыл бұрын
Great tip!
@RaabStephan
2 жыл бұрын
Just saw one of these for sale locally and was wondering about the "One Classic" as I'd never heard of it. How have you been liking it?
@BubblesandthePurrMonster
2 жыл бұрын
What does the feather touch do?
@andrewhondo
2 жыл бұрын
when you cast it when you push the button as a break to stop the line from over casting
@BubblesandthePurrMonster
2 жыл бұрын
Nice, I’ll have to get me one of those off eBay. I’m a sucker for old zebco spin casts. To easy to use, and so much nostalgia.
@billstumpff9651
3 жыл бұрын
I just bought a zebco one classic and started taking it apart to clean it. I watched your video which was a Brest help. One issue I found was that the drag was not working but all the washers were in good shape. The spool however was difficult to remove. My question is, the spool should move freely around the center shaft shouldn't it?
@andrewhondo
3 жыл бұрын
yes it should it could be stuck from oil grease spray wd 40 in and around the center of the spool and the plastic let it sit in heat out in the sun for a few hour or use a blow dryer to loosen the old grease and wiggle it out slowly keep doing the proses over and over tell comes free
@billstumpff9651
3 жыл бұрын
I cleaned it up and it still is super tight, almost like the shaft or spool expanded somehow.
@andrewhondo
3 жыл бұрын
@@billstumpff9651 is yours a one or a 773 with a direct drag system the one has a wide rang drag witch means you have to twist the drag as lose as it will go before you can take off the spool and the direct drive systems didn't have a drag at all and the spools them should pull right off have you tried to loosen up the drag all the way because if you didn't on the one the little drag metal piece will Sentech on the spool tight and won't let go you have to loosen up the drag all the way you have to remove the drag washer as well bye pulling the c retaining clip of with a flat head screw driver
@billstumpff9651
3 жыл бұрын
@@andrewhondo I've loosened the drag all the way , removed the spool (with some difficulty) , cleaned it up, sanded both the shaft and spool so it'll turn but not easily . I'll have to work on it some more. The reel is a
@billstumpff9651
3 жыл бұрын
The reel is a one with the drag by the handle like in your video. The spool just doesn't slide onto the shaft easily.
@ragnaroksangel
Жыл бұрын
Why did you skip how to get it open? What the hell? That's the entire reason I clicked on this
Пікірлер: 17