I must have missed the hole fix part which is what I was waiting for
@parkedredesign
11 ай бұрын
Thank you for the comment. There is a second video to this, where I do the top of the roof.
@comfycozygamer3892
Жыл бұрын
Excellent video. Thank you.
@parkedredesign
Жыл бұрын
I appreciate the comment, thanks!
@thor777mx
Жыл бұрын
Great vid, ended up having to do mine 3 years ago, and this would been a helpful vid.
@parkedredesign
Жыл бұрын
Thanks, hopefully you won't have to do it again (unless you restore another one)!
@billvrbanac2018
Жыл бұрын
great job man
@parkedredesign
Жыл бұрын
Thanks, I appreciate the great comment!
@AdventuresinPopUps
Ай бұрын
Great video, thanks!! Wondering about putting a layer of reflectix in between the roof layers for light insulation? 🤔
@parkedredesign
Ай бұрын
Thanks for the comment, It may help keep some of the summer heat out??
@LetsTubetalk
8 күн бұрын
The question I see when you are liquid nails and nailing in the supports are you nailing that directly to the roof of the camper? Maybe I'm missing something but it's not going to put holes in the top of the camper?
@parkedredesign
8 күн бұрын
No, I used 1/2" nails and the wood supports are 3/4" wide, so the nails do not go through to the roof.
@octanegarage3729
3 ай бұрын
Great video im fixing are roof this is a geat help thanks
@parkedredesign
3 ай бұрын
I am glad you found it helpful, thanks for taking the time to comment friend!
@cali0559
Жыл бұрын
What about the holes in the roof? Isn’t that what caused all the damage? How did you fix that?
@parkedredesign
Жыл бұрын
Thank you for the comment. I posted a part 2 of the roof repair and in that I showed how I repaired the holes. I used bondo to fill in the holes and then I painted the roof with Heng's rubber roof coating.
@patrickbourbonnais8310
6 ай бұрын
There are only 2 types of RVs. The ones that breakdown and the ones that take on water (leaks). 😅 If you're not handy, stick to cottage Air bnb's😂
@markkile8215
Ай бұрын
So if you don’t replace the vinyl on top, all of these repairs are for naut !
@Bettymoo-dp1qv
6 ай бұрын
Hello. I just bought a 97 palomino mustang(or at least im 99% sure thats what it is) and i ave to redo the roof. Your video is suuuper useful. Did you say .197 inch plywood? Im not sure of im just not looking in the right place but i dont see a fraction that equals that😅
@parkedredesign
6 ай бұрын
Yes. I bought it at Lowes. It is called Revolution Ply. It is .197 or 5mm plywood sheathing. It used to be around $16 a sheet but I think now it is more like $26
@thesykboy
Жыл бұрын
How long did this take and what was the overall cost? I’m sure you’d do it MUCH faster than me but I’m still curious.
@parkedredesign
Жыл бұрын
The interior of the roof took me about two eight hour days to finish. The longest part seemed to be cleaning the old insulation out. The outside of the roof took a full day because I had to let the first coat of rubber roof paint dry for four hours before I put on the second coat. The cost of the roof repair was around $650 and that was for the plywood, paint, rubber roof coating, insulation, screws, crown nails. I will be posting a before and after of the pop up and the total cost with the roof and the rest of the interior was just under $1100.
@audrey3319
5 ай бұрын
Amazing and beautiful. Question, if one wanted to just cover that ac hole from outside, what could one do?
@parkedredesign
5 ай бұрын
Thank you, Is your roof metal like this one? If so you could get a thin piece of metal and rivet it over the hole then cover it with the hengs waterproof coating. You could also see if you could find an rv skylight cover depending on the size of the hole and place that over the opening, then you would have a view to the stars :)
@audrey3319
5 ай бұрын
@@parkedredesign thank you!
@avazquez221
6 ай бұрын
I am currently in the process of repairing the roof on my pop-up, and this video helped me figure out how to get it done.. Thank you. However, what is the thickness of the foam board?
@parkedredesign
6 ай бұрын
Glad it helped, I used the 3/4 inch 4x8 sheets of expanded Polystyrene board insulation. I got it at Lowes.
@avazquez221
6 ай бұрын
Thank you
@Szabi9246
3 ай бұрын
Excellent video. I’m planning on doing this tomorrow, but I don’t have nobody to help me remove the roof. Is it doable alone, or it’s crazy heavy?
@parkedredesign
3 ай бұрын
It is heavy, but I was able to get the roof off myself. I just slowly went from side to side and shimmied it to where I could lower it to the ground, if that makes sense.
@Szabi9246
3 ай бұрын
@@parkedredesign perfect, thank you my brother
@parkedredesign
3 ай бұрын
@@Szabi9246 No Problem!
@enzopeirano5417
Жыл бұрын
Why did you use different staplers and the first one you used where it was fixed? If the ceiling is very thin, they did not manage to pass to the other side.desde Chile 🇨🇱 😊
@parkedredesign
Жыл бұрын
I used the wide crown staples to tie the cross stringers to the stringers that ran down the length of the roof. I was a little concerned that it would go through, but I tested it first and it did not. I used 3/4 inch (1.9 cm) staples and turned the air down a little on the compressor. I used the smaller crown staples to secure the panels to the stringer. For those I used 1/2 inch (1.27 cm) crown staples. The stringers were 1 inch x 3 inch (2.5 cm x 7.6 cm) Hope that makes sense.
@decentgarage
6 ай бұрын
Did you glue the insulation right to the canvas top?
@parkedredesign
6 ай бұрын
Yes, I used the fuze-it extreme temperature construction adhesive to glue it to the top. This top was an aluminum skin. I then glued and stapled the wood panels to that.
@do8717
2 ай бұрын
Dude!.....By the look of it, you should be spending all that time....working on that house!😂
@parkedredesign
2 ай бұрын
It sure needs it! 🤣
@carterfilion8195
3 ай бұрын
Would you be able to provide a list of the materials you ended up having to use?
@parkedredesign
3 ай бұрын
I can, I am out of town working and don’t have my computer. I will list it in the comment section when I get back.
@carlamann3316
4 ай бұрын
Q? Whats holding up the cross beams STOPPING the roof from dipping in the center ? And collapsing the cross beam at not attached to the frame? It will sink like ours down the middle if there is weight ?
@parkedredesign
4 ай бұрын
The metal cross beams are attached to the roof with screws through the wood stringers. The metal cross beams have a slight curve to them which I believe it is suppose to help curve the roof so it does not sink down.
@mauriciomontero2039
11 ай бұрын
What did the wife crown staples fasten to? Is that foam or sheet metal ?
@parkedredesign
11 ай бұрын
There was the original wood stringers that ran down the sides that I did not remove. That is what I stapled the new cross stringers to. The ones that ran down the side were not rotted, that is why I didn't replace those.
@melpate626
26 күн бұрын
A Camper is the thing that goes in the bed of a truck. Palomino makes a pop-up camper. This is a pop-up tent trailer.
@parkedredesign
26 күн бұрын
Ahh, I see.
@kayliecramer8374
7 ай бұрын
Did you buy new metal supports or were those the original?
@parkedredesign
7 ай бұрын
Those were the original ones, I just painted them.
@paulofell9939
5 ай бұрын
How thick is the top of the roof? What size screws would you use so they dont just penetrate tbrough the other side
@parkedredesign
5 ай бұрын
This roof was a thin aluminum not sure of the thickness but it was pretty thin. For the crown staples that I used to attach the center wood stingers to the side stringers they were half inch (the stringers were 3/4 inch wide) To attach the ceiling panels to the stringers I used 1/2 inch narrow crown staples (as well as liquid nails during both processes) To attach the metal support brackets to the ceiling panels I used 3/4" screws.
@chandersman
Жыл бұрын
When you are nailing the stringers in, any concern that you'll puncture rhe roof? What are you nailing into?
@parkedredesign
Жыл бұрын
I was a little concerned that it would puncture the roof. The stringers I used were 1x3 and the shortest wide crown staples I could find were 3/4 inch. I turned the air down on my compressor and tested it first to make sure it did not penetrate the fiberglass because the 1x3's are not a true 1" wide. (I did not show that in the video, and it did not penetrate). If it had I would have probably use the metal straps and screws that were 1/2 or 5/8's. The original roof was tied together with glue and crown staples so that is what I used. The crown staples nail to the two stringers that ran lengthwise on both sides. Those fortunately were still solid and I did not have to replace them. I should have shown a close up of that. Hope that makes sense. If not let me know and I will look through my videos and see if I have a close up of it.
@chandersman
Жыл бұрын
@@parkedredesign Thank you! Super clear and helpful. My father in law just gave us the exact same model of camper... And I'm trying to figure out if it's a blessing or a burden, because it has a lot of needs. Your video helps a ton, because now I feel like we can tackle this.
@parkedredesign
Жыл бұрын
@@chandersman I say it is worth it to fix it up. Check back in a few days, I am going to have the second part of the roof video posted (exterior side) and then the before and after video of the palomino pop up restoration. It came out great! (at least I think it did, lol) If along the way you have questions, please feel free to ask. I will let you know that we did put about $1500 into it with all the restoration, paint and interior touch ups, but if you got it for free I know you could sell it for much more and recoup the money if you ever needed too.
@andrewradom3772
2 ай бұрын
How did you lift the entire roof off and get it on the ground
@parkedredesign
2 ай бұрын
After I unbolted it and it was in the lowered position I went back and forth from each end and shimmied it a little at a time until I could get in the center and lower it to the ground, if that makes sense.
@andrewradom3772
2 ай бұрын
@@parkedredesign gotcha , thank you
@parkedredesign
2 ай бұрын
@@andrewradom3772 My pleasure
@bobmcnelis3648
Жыл бұрын
Not being a wise guy, but how about the wiring? There are no ceiling lights, or a 110 line for the AC? Great work otherwise! I’m going to follow your lead on my Coleman.
@parkedredesign
Жыл бұрын
Sorry about not showing that. I used the original wiring which was not put inside the ceiling. The wire for the AC was a wire with a plug that I ran along the ceiling then down the side and plugs into a wall outlet. I hid with a cable cover raceway, I used the same cable cover raceway to hide the wires for lights as well. So the wire were not put in the roof if that makes sense.
@enzopeirano5417
Жыл бұрын
Por que usaste diferentes grapadoras y estás donde se fijaron no pasaron por el techo al ser tan delgado
@parkedredesign
Жыл бұрын
La grapadora de corona ancha se usaba para atar los largueros de madera. Las estrechas grapas de la corona se utilizaron para asegurar los paneles a los largueros.
@enzopeirano5417
Жыл бұрын
@@parkedredesign ok thank you very much this week I will dedicate myself to fixing the roof of my pop up so I don't pay for a technical service in this and I save that the materials for occupying so thank you for sharing your videos I hope everything goes well and it doesn't get worse hahahahahahahaha
@parkedredesign
Жыл бұрын
@@enzopeirano5417 Ok, good luck. I check the comments regularly so if you have more questions feel free to ask. I will be posting the before and after of ithe pop in the next few days.
@enzopeirano5417
Жыл бұрын
@@parkedredesign excelente bendiciones
@janetblair2259
4 ай бұрын
wOULD YOU BE WILLING TO DO ANOTHER?
@parkedredesign
4 ай бұрын
Eventually I would love too! My work has had me traveling so much I haven't had much time to work on even the new camper I got for myself. I haven't posted a new video in a while because of this, but hopefully I will soon.
@gaviningram8348
Жыл бұрын
👍
@parkedredesign
Жыл бұрын
Thanks for the thumbs up!
@MarkW-j2k
Ай бұрын
No adhesive from the styrofoam to the panelling? Oops.
@parkedredesign
Ай бұрын
Nope, but it's holding up good so far!
@jamesshackelford4173
4 ай бұрын
Could you not cut that layer out
@parkedredesign
4 ай бұрын
Not exactly sure which layer you are talking about, but if it was the foam layer, I couldn't cut that because I didn't want to risk cutting the thin metal roof.
@melpate626
27 күн бұрын
First of all that’s NOT a camper…..its a trailer!
@parkedredesign
26 күн бұрын
Thank you for the comment. I am a little confused by it tho. Why would you say it's not a camper?
@oakley1471
Жыл бұрын
"promosm"
@parkedredesign
Жыл бұрын
Not sure what that means but thanks I think, lol
@takotlensky
Жыл бұрын
Literally clicked on this to dislike it because of that camera holding
Пікірлер: 81