Just fixed dripping tub faucet earlier thanks to this! Needed new spring and seat. Thank you!
@Teach2Build
10 ай бұрын
Wear it with pride, my friend. You just saved yourself a pricey plumbing service call.
@xyy8774
Жыл бұрын
Thanks for your video. Can you share names of two tools used here to remove the handle and the other to adjust the seed and coil. Do they have specific size required for this job.
@Alex-zs7rv
Жыл бұрын
That's a great video but I've got the Delta Flynn bathroom faucet and the there are no hex screws or slotted screws holding the handle on. HELP!
@matts53gmc
Ай бұрын
Nice video for handles. How about explaining when the spout gaskets leak no instructions to remove milain spout for gasket replacement just took Chanel locks to mine about ripped water lines off still no budge
@j109joell
Жыл бұрын
Thanks!
@kkeenan536
8 ай бұрын
You make it look so easy getting the seat back in. I cannot get it (if it is supposed to be depressed down into where the spring is)
@Teach2Build
8 ай бұрын
The spring goes in first, then set the rubber seal on top of that, so that the seal rides against the handle/ball. Best of luck with your repair!
@kkeenan536
8 ай бұрын
Thanks for the reply but does the seat recess down into where the spring is (so it looks the same as when I took the old one out)@@Teach2Build
@cherokeesprings
2 ай бұрын
Great information. But like others, my problem is a little different. I have a Delta KITCHEN faucet with two handles. No idea if it has cartridges (I can hear y'all laughing), but it definitely doesn't have a set screw. It's leaking around the base and the hot water handle for sure. I'm a novice, so I need to have a decent idea of what to do before I jump into this. HELP! We need a video ASAP!
@SusanA-kb7gc
Ай бұрын
Would be nice if you show how the cartridge is positioned so the handle turns the correct way and on/off work as they should. I tried and when handle is in on position there is no water. Handle in off position then water flows. The cartridge is a 90 degree type.
@Linlinie
6 ай бұрын
how do I know what teespring size I need as I do not know the model of the Delta kitchen Gooseneck faucet, but It does have two handles
@Teach2Build
6 ай бұрын
Oooo. That's a good question. I might start by calling Delta customer service. They're great.
@paulknoblock8797
8 ай бұрын
Which way does spring go back in? I know but do millions others?
@MrPDGee
7 ай бұрын
Big end down (they're slightly tapered)
@432b86ed
11 ай бұрын
No Allen set screws on mine. ?
@MrPDGee
7 ай бұрын
If there's not allen (or slotted) screw on the side of the handle, then there's a screw on the top of the handle, usually under a cap that just pops off for access. The cartridges have a flat (for the set screw) and a threaded top so can be used in faucets with either type of handle.
@432b86ed
7 ай бұрын
@@MrPDGee I appreciate your response, but there is no top/center fastener. The way in which the handle is removed is by turning the whole bottom portion (bezel) of the handle assembly, which is threaded on to the cartridge. This lifts the handle off the cartridge shaft. I couldn't get mine to budge due to hard water deposits. Regards
@negocios0rsk
2 ай бұрын
I have a Delta 2 Handle faucet with no little set screw. I have checked thoroughly. It looks a lot like the faucet in your video except the 'tower" base of the faucet is stationary and there's a seam at the top where the handles move. I am perplexed! Any ideas? I'm leery of applying force until I understand. 😀
@Teach2Build
2 ай бұрын
Sometimes, there's a cap that'll expose a screw. There are also models that you hold the handle stationary while unscrewing the escutcheon (trim ring) underneath it. Don't give up, you've got this!
@negocios0rsk
Ай бұрын
@@Teach2Build. It turns out the whole valve handle is like a bonnet that simply unscrews ! I bought a “rubber wrench” to avoid scratching the finish. After that, the whole job is the same. Of course, both shutoff valves had to be replaced first!😂. So, I didn’t have to leave the whole house water off while I matched the new Delta parts at the hw store. Thanks for your guidance!!
@Teach2Build
Ай бұрын
Congrats on a job well done!
@arthuruscg
19 күн бұрын
There's no hex/Allen keys holding on the handles. They've eliminated them
@Teach2Build
19 күн бұрын
As mentioned in the video, there's a variety of styles. Some just unscrew near the base, some have a cover of sorts hiding a screw. I've even seen some that are a simple press fit! Best of luck with your project!
Пікірлер: 25