Awesome. Need to repack my exhaust and your video helps a lot. Thanks, Daniel!
@wydopensports8335
7 ай бұрын
Thank you so much! That was super helpful!
@DanMX2112
7 ай бұрын
Thanks for watching and I’m glad it helped you!
@aleks5069
2 ай бұрын
Изолента синяя😂💪. Обычной ниткой достаточно👍
@bike_life6254
3 жыл бұрын
What size rivets would you reccomend? Do i need steel ones? Or will aluminium do?
@DanMX2112
3 жыл бұрын
I think either will work, but steel is what was came out. And I think they are 3/16” rivets but I can’t remember?
@thomasjameson5761
3 жыл бұрын
Quick question wouldn’t you want to use the silicone in between the two pieces, not just at the edge of the connection?
@DanMX2112
3 жыл бұрын
I really don’t think it matters, as the sealant is not there to hold pressure. From the factory they just bead the edge to help with exhaust blow by, otherwise it would turn black and look bad. Again it’s not fro pressure, but just to seal back blow by. When you do seal both opposing pieces, you make it very difficult to separate the two, and don’t really accomplish much more in the fact of closing the exhaust up. Hope this helps, and thanks for watching Thomas!!!
@Fixin2Ride-Official-
3 жыл бұрын
Technically Speaking, Yes! He should have. Looks like the packaging even stated that. Also Shows a Picture at the bottom of the instructions on the bag of sealant being applied to the end cap rim that inserts into the muffler bore while the end cap is still out of the muffler a bit. "Step 10. Reassemble the muffler by tucking in the fresh packing material as you slide the core into the canister. BEFORE the front end cap is INSERTED, apply a thin bead of High Temp Silicone around the end cap for an improved seal. Be sure the inner core of the muffler aligns with the rear end cap before fully inserting the front end cap into the canister (Fig. 5). www.fmfracing.com/content/instructions/000362.pdf
@DanMX2112
3 жыл бұрын
Nice! I do remember reading that, and took the route of doing the bead afterward. Good info and I think either way is fine. Thanks Andrew, I appreciate the comment man!!
@gohobby9934
3 жыл бұрын
That was super helpful. I will subscribe to show my appreciation!
@DanMX2112
3 жыл бұрын
Thanks man, i really appreciate it! Have a great Thanksgiving!
@mrcla55yguy20
2 жыл бұрын
Is that painters tape you put around the wrap? Did you leave it? It won’t catch fire?
@DanMX2112
2 жыл бұрын
Yes sir, just painters tape. It won’t catch fire, it’s all good, been using it for years.
@mrcla55yguy20
2 жыл бұрын
@@DanMX2112 lol that’s awesome. Thanks for the swift reply. Saw it at work earlier. I’ll use it.
@DonGH297
4 ай бұрын
Very helpful thanks mate
@DanMX2112
4 ай бұрын
Thank you!
@munkyassproductions9178
2 жыл бұрын
nice video repacking my big gun for the first time
@DanMX2112
2 жыл бұрын
Heck ya, thanks man and good luck on the big gun. Those pipes are throaty!!!
@pcmountaindog
3 жыл бұрын
So the packing needs to be replaced yet the mufflers are riveted to gather? What kind on design is that? Then there is the issue or spark arrestors. How are sparks going to get through all that junk?
@DanMX2112
3 жыл бұрын
So the packing is there to add back pressure and silence the exhaust. This exhaust has no spark arrestor, therefore is literally fire breathing lol the inner exhaust tube is open and that is how the sparks travel through. The rivets are there for replacement purposes as shown in the video. Good stuff brother! Thanks for watching man!
@benwood04
3 жыл бұрын
Thanks for making this video! I have a LONG Husaberg exhaust to repack.
@DanMX2112
3 жыл бұрын
Your welcome, glad I could help! Good luck with the repack and please share the video!
@grantdorcey8053
Жыл бұрын
I’m doing mine on my 08 yz450 and got it apart and wondering what is on the other side of cap. Is there more packing behind there? Thx
@grantdorcey8053
Жыл бұрын
I think 08 muffler is different than yours
@DanMX2112
Жыл бұрын
The 08 is shorter, and no there is nothing behind the cap. Thanks for watching and good luck Grant!
@grantdorcey8053
Жыл бұрын
@@DanMX2112 thx you
@danjim7056
3 жыл бұрын
I have an old white brothers e series for my 426 bit the baffle is busted off so it rattles. Not sure how to fix the baffle or if packing will hold it in place?
@DanMX2112
3 жыл бұрын
No, if the baffle is broken then it needs to be re-welded on. The packing will keep it somewhat centered but it’ll just end up doing the same thing in a very short period. Thanks for watching my friend!!!
@markwarman782
4 ай бұрын
Really good thanks
@fraserthompson6084
4 жыл бұрын
I done the exact same thing riveting my exhaust and scratched it on the first rivett 😭 Great video though, really useful!
@DanMX2112
4 жыл бұрын
Lol that thing almost shot me in the eye!!! Thanks for watching!
@starwarscrazy4540
Жыл бұрын
The old wire wheel works great for cleaning up internal and external parts of muffler.
@DanMX2112
Жыл бұрын
For sure, and man that is a nasty job. 2 stroke silencers are the worst.
@zhuliu
Жыл бұрын
Is the packing just fiberglass?
@DanMX2112
Жыл бұрын
Yes sir!
@GreenChronicles561
2 жыл бұрын
Great video. Wish you would have done a before and after for the sound
@DanMX2112
2 жыл бұрын
I know me too, but it wasn’t my bike!
@iulianzaharia5710
4 жыл бұрын
Good video mate ! Will gone help me a lot ! Can you tell what kind of tape did you use there ?
@DanMX2112
4 жыл бұрын
Just regular masking tape used for painting. It melts easy and comes out on the next job. Thanks for watching I appreciate you Lulian!
@seanpotter4943
3 жыл бұрын
I did mine. First run the exhaust was smoking when I stopped. That normal for new packing?
@DanMX2112
3 жыл бұрын
Usually had a slight smell and smoke to it, normal and no big deal!
@seanpotter4943
3 жыл бұрын
@@DanMX2112 yeah was thinking that. Wasn't panicking just wondering. It wasn't an engine Smell pure burning . Thanks bud
@DanMX2112
3 жыл бұрын
Heck yeah man thanks for watching!
@temujinkhan4986
2 ай бұрын
Does the tape just burn away 🤔
@DanMX2112
2 ай бұрын
Yep, just burns off and allows the packing to work its magic!
@robertcadiz4346
2 жыл бұрын
Awesome video
@DanMX2112
2 жыл бұрын
Thanks Robert, glad you enjoyed it!!!
@sivnnadav1
2 жыл бұрын
Hey, can you show how to replace only the end cap while the exhaust in attached ?
@DanMX2112
2 жыл бұрын
Everything you need regarding that is In this video, unless your talking about the spark arrestor, as this one does not have one.
@Runk3lsmcdougal
3 жыл бұрын
Very helpful thank you
@DanMX2112
3 жыл бұрын
Thanks for watching, I appreciate it!!!
@BHMoto
3 жыл бұрын
Great video thank you so much man 👍
@DanMX2112
3 жыл бұрын
Your welcome my man, thanks for watching and please share it with others!!!
@turboflash_
Жыл бұрын
What size rivets did you use?
@DanMX2112
Жыл бұрын
I’m thinking they had to have been 3/16”. I had a kit with different sizes. Whatever hole you drill use that size of rivet.
@turboflash_
Жыл бұрын
@@DanMX2112 ok thank you very much.
@pattyaylward7339
3 жыл бұрын
if u take all the packing will it blow up
@DanMX2112
3 жыл бұрын
The only reason for the tape is to hold the packing together until you slide it in the silencer. That’s it, just do as I did in the video and you’ll be fine.
@borntwice4724
4 жыл бұрын
Great video brother helped out a lot.👍
@DanMX2112
4 жыл бұрын
Glad it helps, that’s the goal! Thanks for watching man!
@buildsendrepeat2473
4 жыл бұрын
Hey mine has this extra mesh around the tube in the Packing should not be in there could possibly be making it louder because it is very loud
@DanMX2112
4 жыл бұрын
some exhausts come with the mesh, but your new packing more than likely will not unless it is oem.
@adamgordon9380
3 жыл бұрын
You never mentioned what you used the popcorn for?
@DanMX2112
3 жыл бұрын
Haha 😂 to remain sane! That’s awesome, I’ll be more specific in the future lol thanks Adam!
@burt1758
Жыл бұрын
Wrapping it too tight or loose hinders performance.
@DanMX2112
Жыл бұрын
Yes sir, it’s can’t be so compressed it’s solid. Good point, thanks for sharing!
@otisgarrigan5890
4 жыл бұрын
Do you have to have the rivet tool to do it
@DanMX2112
4 жыл бұрын
Otis Garrigan some people use self tapping screws, but either way works. The river tool will hold up, screws will back out eventually. Check my link in the description below and pick up the tool for cheap! Thanks for watching!
@lemonteb6087
3 жыл бұрын
Does crf150 have this ?
@DanMX2112
3 жыл бұрын
Yes, it has replaceable packing in the silencer!
@elsuarze7
4 жыл бұрын
how was the sound before and after?
@DanMX2112
4 жыл бұрын
Alvaro MASTER Beas it sounded like a pop can before. Now it sounds deep and low like it should lol I didn’t get a before sound so really had nothing to compare.
@elsuarze7
4 жыл бұрын
@@DanMX2112 great job!!!
@originalrr3800
3 жыл бұрын
before and after sound would have been nice :D
@DanMX2112
3 жыл бұрын
I would have, but never got footage of before. The after sound is on the Lake Murray Ride video. Check that out! Thanks for watching brother!
@swemx7403
11 ай бұрын
Seriously? Your camera died JUST at that moment huh? How many roll around the baffle do you need to do? One, two or more?
@DanMX2112
11 ай бұрын
Dude, if you had any idea how many times the camera has died during something important lol it never has happened on an easy step, except in this video. Roll it loosely till it’s slightly larger than the inside diameter of the pipe, not rocket science my guy. Thanks for watching!
@andrewlynch1921
3 жыл бұрын
Good video next time turn the music down thanks man!!
@DanMX2112
3 жыл бұрын
Noted!
@Jjrock148
3 жыл бұрын
Took about 6 hours longer then your video. Next time will be better. Thanks for the video
@DanMX2112
3 жыл бұрын
It’s all fun the first time lol I know how it is my man! Thanks for watching!
@joejohnson7385
2 жыл бұрын
Why not buy an upgraded muffler?
@DanMX2112
2 жыл бұрын
Lol I wish, and no need. $30 for packing or $200 for upgrade, stock works fine 😛 Nobody but the pros even use all that 450 power to justify it. Thanks Gary, I appreciate you watching!
@starwarscrazy4540
2 жыл бұрын
They make it look easy it is not at all mine took days to get off following the utube videos. Ended up using razor blade to cut silicone from underneath the can and a punch to drive the can off. Repacking not easy either always bunching up trying to put back on can and lining up holes don't forget the red silocone either
@DanMX2112
2 жыл бұрын
Dude my first one was a nightmare, and some are very stuck. Glad you got done and I hope the video helped out! Thanks for watching!
@machines4life450
2 жыл бұрын
Bit disappointed the camera died I like point to point videos but that’s alright.
@DanMX2112
2 жыл бұрын
Me too, I was bummed out bad!
@hurstshiftin9873
3 жыл бұрын
You don't even need the band's.
@DanMX2112
3 жыл бұрын
Yamaha did, so I went with it. No biggie.
@paulhetherington3854
7 ай бұрын
I proved, why HRC | KTM = "Can replace - any core(kor)!" Used - racist "Swap Moto - sound!" And he, illegally - used our prosuct: "On a public - domain?" I.e. Oriental radar! 2nd Amend - "No personal Venue!" Only - chosen mechanics - from our: "Shop can - do demonstrate!"
@DanMX2112
7 ай бұрын
Who takes the time for this ⬆️
@idecidenotyou
6 ай бұрын
I agree.. this dudes got daddy issues..@@DanMX2112
@kyleroenfeldt1092
2 жыл бұрын
Where can I buy rivets ? I need ones to fit the stock exhaust to a 2003 rm 125
@DanMX2112
2 жыл бұрын
Anywhere hardware store or online. They are very universal so don’t think that you need OEM rivets, you won’t find any. Buy the match to the ones you drill out.
Пікірлер: 100