Excellent vid! So basically Read ISN from MSD81, Copy New ISN to CAS, Perform Injector coding. Then you just flash an mhd which should write vin in uif? But i've heard stuff about Reset working hours on MSD81? What actually is this and is it required? Cheers
@chesapeakemotorwerks
Жыл бұрын
Yes, that's correct. No working hours reset needed as long as the DME came from a like vehicle.
@Imurat55
3 ай бұрын
can you do video using ESYS , inpa ?
@jordonbsupoto7858
4 ай бұрын
If you buy a used msd81 ecu do you have to Virginize before installing it?
@chesapeakemotorwerks
3 ай бұрын
Not the way I did it but you do need to write the ISN into EWS.
@husainamin8377
6 ай бұрын
Why didn't you change the MSD81 DME ISN with your old ISN instead of changing CAS ISN?
@chesapeakemotorwerks
5 ай бұрын
CGDI didn't support overwriting the MSD81 ISN, it's only able to overwrite the ISN in the CAS (at least when I filmed this)
@iloveinsanegirls
Жыл бұрын
Can we get links to all tools used my 335i has been down for a month over this nonsense
@chesapeakemotorwerks
Жыл бұрын
I bought my CGDI Programmer used on Ebay. It's available new here (no endorsement) www.cgdishop.com/wholesale/cgdi-prog-bmw-msv80-car-key-programmer.html and you will need the MSD80/81 ISN authorization. You need to search for INPA (BMW Tools) and this cable works well amzn.to/3k1XlsJ
@TML34
Жыл бұрын
How do you write vin in msd81 to match cas? Smog checks will read whatever vin is on msd81
@chesapeakemotorwerks
Жыл бұрын
You can see my "BMW ECU CAN bus Man-in-the-Middle with CANBadger" video for how I did it, but WinKFP will do it for a stock tune. Following the video above and some posts online that gained attention, I believe MHD also writes the chassis VIN to the DME now so it will match the CAS VIN.
@TML34
Жыл бұрын
@@chesapeakemotorwerks fair enough. I’ve got mhd, so hopefully the flash does it. Thx
@jonbilek1546
8 ай бұрын
@@TML34 I'm having same issues and have mhd will it work I bought good ecu from junk yard
@a.b.ripper9908
Жыл бұрын
So i cloned my old one to a new one, and my car starts, but i cant reach the dme and i have every code pop up, do i need to program my new cloned dme to my vin?
@chesapeakemotorwerks
10 ай бұрын
IIRC, it will throw a code (should only be one) with a VIN mismatch. What you're describing sounds like you need to reset adaptations & clear codes.
@a.b.ripper9908
9 ай бұрын
@@chesapeakemotorwerks i figured it out, my guy that cloned it didnt clone everything, but i got it figured out
@goosesalsa1664
Жыл бұрын
If I have mhd on my msd80, do I have to take it off the msd80 before I switch to msd81? When I switch to msd81, can I just re-add the tune with no issues?
@chesapeakemotorwerks
10 ай бұрын
You don't need to take it off the msd80, the license is tied to your VIN which is read from your vehicle immobilizer so it will just work.
@austindoud273
Жыл бұрын
Neat
@samuelprusinski
2 ай бұрын
I know this is an old video but I need help pairing a separate CAS and DME to my car that did not have one. Is this something you could help with?
@chesapeakemotorwerks
2 ай бұрын
I currently don't offer this as a service. If you are completely out of luck I might be able to arrange something. Right now i don't even know if my CGDI is currently licensed :-/ hope you figure it out!
@ChadFreeman757
10 ай бұрын
You’re in Chesapeake, VA? If so, I’d like your help.
@chesapeakemotorwerks
10 ай бұрын
Further north in MD, but I've been traveling a lot lately.
@ChadFreeman757
Ай бұрын
@@chesapeakemotorwerks I’m thinking of doing this upgrade. I had MOSFETs replaced in my MSD80, my 30BB is still present & won’t clear. It’s been forever. I’m ready to drive my car. Idk if it’s easier to just buy a MSD81 & CAS together or what…
Пікірлер: 26