I was watching your video, I picked up this mower cheap and needed to replace most of the springs and belt, your video helped showed the location and how to install new-belt, and springs which I have. Great job on video I followed it completely worked like a charm. now good to go! thank you very much:)
@Srt8Jeep
Жыл бұрын
I had an extra spring when I reinstalled my deck. 😂 Thanks to your video I figured out where it went!
@DougHall65
Жыл бұрын
Thanks, Jason. Very helpful.
@VickiMcKeen
Ай бұрын
Thank you for the video. I had an issue with a pulley and you helped me with that.
@edhartman2860
Жыл бұрын
I was looking for a video showing the removal of the spring and engaging cable.... Thanks, it looks like I can do that...Good video...I have the Cub Cadet LTX 1042, same set up...
@justinsweet2028
Жыл бұрын
Glad it helped
@bryanscheeler
2 ай бұрын
Thank you this was extremely helpful
@mybrass41
3 ай бұрын
So clear! Thx!!
@rogerdodger1831
Жыл бұрын
Thanks for the video, is there any adjustments to make the belt a little tighter ? I just replaced the same belt with the correct part number ,it's flopping more than it should ,
@1randyful
Жыл бұрын
At 11:00 minutes you show the 'L' bracket' under the idler pulley, being mounted on top of the main mounting bracket. It should be underneath that mount being held by the bolt that holds everything together. the short side of the 'L' should be touching the deck.
@michaelbarcz326
Жыл бұрын
Dude ya gotta get someone - ANYONE to hold that phone
@aaronwism
Ай бұрын
Tripods are cheap!! 😂
@boogaloo62
Ай бұрын
Thank you
@sissymurphy9620
Жыл бұрын
3 screws on each deck belt cover as grass will push the cover up that gets caught under them . The new cub cadest at least have the new covers that don't allow that to happen They are metal and have openings to allow grass to be pushed out . I am having problems with the belt coming off and the screws to the belt holders keep coming down and rubbing on the pulleys . I ordered the new covers for my 2016 cub cadet hydrostatic since the screw holes match it . I am hoping that will solve the problem of the belt coming off while mowing . I also had to level the deck side to side
@beerleagueeverything8030
Жыл бұрын
Are the covers just to keep the user from stepping or knocking something into the pulleys and damaging them? Half tempted just to keep mine off. I get the grass build up as well.
@sissymurphy9620
Жыл бұрын
@@beerleagueeverything8030 if you take the covers off the belt keeps coming off . I tried it and belt kept coming off , The metal posts in the covers hold the belt . I hate the plastic covers as they just hold grass that is hard to get out . But found out not as much grass got stuck under the covers when I changed to gator blades and cleaned the underside of my deck and applied slip plate graphite to keep grass from sticking to the underside
@beerleagueeverything8030
Жыл бұрын
@@sissymurphy9620 thanks!!
@sissymurphy9620
Жыл бұрын
@@beerleagueeverything8030 your welcome and plus I ruined 1 belt by taking the covers off . So glad I could help . Try slip plate graphite under you take I have been a fan of it since my son who owns a towing company uses it on his flatbed tow trucks . It is a little expensive for a quart but 1 quart will do 2 lawnmowers and lasts for years and that is doing 3 coats and still some left over so did mny push mower and still sme left . I got my can on e bay
@kostia1975
Жыл бұрын
ltx1042 I replaced the idler pulleys with new ones, and after tightening them, they are not loosely spinning, is that normal?
@stevendiffy768
4 ай бұрын
What clip did you use in place of the bowtie clip?
@justinsweet2028
4 ай бұрын
Hair pin cotter key looks like a R
@mytruthslays1303
Жыл бұрын
Why is there no tension on the belt?
@RicardoBigTime
11 ай бұрын
Your your attention comes when you actually activate the blades while you're riding that's what pushing that lever forward does
@user-xv2qf2vs7k
8 ай бұрын
Show me how to tighten the belt
@user-nd5bx8fk6v
4 ай бұрын
We have Mulch Plug that may fit your lawn tractor. We can provide for free. Do you need?
@LolethaBoyd-ct9dz
Жыл бұрын
Belt keeps jumping off
@michelboisvert5684
Жыл бұрын
hi, before working on your machine, wouldn't you like to clean it instead of working in dirt, because it would be much better
@justinsweet2028
Жыл бұрын
You absolutely can clean it / wash it but then you getting nasty water all over ya little dirt never hurt ya
@RicardoBigTime
11 ай бұрын
What size built isn't because there's no way in hell the 42-inch that I got reaches. It looks like it should be 60 to 80.
@nathananthony2552
11 ай бұрын
Ya, I bought the belt for a 1040 ltx but it's too small or I'm not doing something right.
@ashriver7710
11 ай бұрын
@@nathananthony2552the 42" measurement is the size of the deck. Ltx1040 takes a 96" belt I believe
@barbwire4879
Жыл бұрын
Dam. I said. ,46 in not a 42. Dam you tube
@coachtyler_
Жыл бұрын
A lot of skipping
@stanbryant7360
Жыл бұрын
try cleaning the grass off
@Srt8Jeep
Жыл бұрын
Try not being a douche
@justinsweet2028
Жыл бұрын
It's not a how to clean the deck because we don't want to get dirty its to show you how to save a cuple hundred at ur local rip off shop
Пікірлер: 36