Works a treat now. Very helpful disassembly instructions on your video. Washing machine now behaving normally after a few frustrating years on the old PCB jumping around between the various programs ....!!! Thank you.
@eSpares
6 жыл бұрын
Thanks for the comments, glad to here you have sorted the problem.
@DaFuqFM
4 жыл бұрын
A life saver. Thanks bro
@eSpares
4 жыл бұрын
Glad to hear this. Thanks for tuning in!
@soulfulshoes
3 ай бұрын
On the hoover washer dryer I'm changing the heater thermostat as shown in another video. The top has plastic trims around the side, which hold the top on not the same as you show. I've removed the back trim. How do I remove without breaking the trims. Thanks
@vlmaguire81
4 жыл бұрын
Thank you so much xx
@TheLaundryCentre
9 жыл бұрын
The best way, to change a PCB/module or timer is to change one wire or one wire connector block at a time, if there is enough wire length to do so.
@eSpares
9 жыл бұрын
Thanks for your comments, and It is certainly a good way to start but we would always recommend you take reference photos as one slip with a PCB,module or switch bank can pull off wires. Without reference photo's it can be very difficult to know for certain where the wires came from especially if the board has connectors that are not all used. :-)
@tonybaines3332
7 жыл бұрын
the main pcb at the bottom of the washer can easly be connected wrong, take a pic like espares say.
@louisea8966
7 жыл бұрын
Hi what tool do I use to took about the hex screws in this washing machine. I am having real problems working out the correct one to get in to it
@eSpares
7 жыл бұрын
Hi Louisea, see our web site: www.espares.co.uk/product/es1251179/9-piece-torx-head-screwdriver-set
@ricardpdasilva2779
6 жыл бұрын
i have a candy grand o goc 218-80 can someone show me the diagram for the wiring on the control panel please . i disconnected and didnt take photo silly me .
@eSpares
6 жыл бұрын
Hi ricardp, we do not have access to wiring diagrams but thank you for pointing out how important it is to take a photo.
@chrisbones5354
6 жыл бұрын
hoover 31005589 i put the pluginto mains sock/et d leds come on momentarily unplug it and leave it a few seconds plug back in and same again.I cant use the machine what is wrong with it anybody know whats wrong with it please
@eSpares
6 жыл бұрын
Hi Chris, have a look at this video for help kzitem.info/news/bejne/so-G16SghYhopmk just copy and paste into your browser.
@tonybaines3332
7 жыл бұрын
is it important to replace the film cover ?
@eSpares
7 жыл бұрын
Hi Tony, the plastic film between the PCB and the front panel shown at 3:45 is there to protect the PCB from contamination tat could leak through the buttons. The machine will work perfectly without this but if liquid is spilt on the front it could reach the board and cause damage. If the old film is blackened from a short cut away any carbon'd area and reuse it patching the hole with insulation tape.
@tonybaines3332
7 жыл бұрын
bloody hell ime gonna aftoo take it to bits again for the 100th time, thanks for that ... lol, no i mean thank you tony
@eSpares
7 жыл бұрын
Never mind Tony, you must be good at that now lol. Thanks for the comments. 😊
@tonybaines3332
7 жыл бұрын
thanks for the vids, over the years its helped me out no end.
Пікірлер: 21